|
|
Design of the system for the carbon composite conductive layers of the L-39NG aircraft testing and the optimization of the conductive material
Pham, Ngoc Nam ; Hönig,, Martin (referee) ; Háze, Jiří (advisor)
V posledních desetiletích je v leteckém průmyslu výrazně preferováno použití kompozitů. Nejnovější projekty českého leteckého průmyslu se zaměřují také na zvýšení využití kompozitů v nových letadlech. Tato práce se zaměřuje na výzkum elektrických vlastností kompozitu za účelem optimalizace výběru materiálu. Diplomová práce představuje návrh automatické měřicí stanice sloužící k měření a testování elektrických vlastností kompozitních vzorků vyráběných společností AERO Vodochody AEROSPACE as. K tomuto účelu je použito zařízení LCR bridge R&S HM8118 a řídicí program je navržen v prostředí MATLAB s použitím jazyka SCPI. Navržený systém je následně použit pro experimentální ověření elektrické vodivosti kompozitních vzorků. Výsledky měření budou základem pro vývoj kompozitů pro leteckou vodivost v nových letadlech. Tato práce také prezentuje výsledky testu úderu blesku na vybraných kompozitních vzorcích. Výsledky testu na úder blesku poskytují hlubší znalosti o schopnosti vzorků chránit před úderem blesku. V této práci je také představen vývoj nedestruktivního testovacího systému založeného na metodě elektrické impedance/odporové tomografie. Vývoj je v prvních fázích, ale očekává se, že systém bude využíván jako systém monitorování zdraví struktur.
|
|
| |
|
| |
|
|
Evaluation of quality welds on chains for harvester
Teuer, Tomáš ; Kubíček, Jaroslav (referee) ; Sigmund, Marian (advisor)
The diploma thesis examines the influence of setting welding parameters and welding process on the resulting structure and strength of the welded joint of harvester chains. The theoretical part discusses the problem of weldability of pine steels by using method “135” with the possibility of destructive or non-destructive testing of welded joints. In the practical part, this matter is examined on a specific weldment, the harvester chain. Cross member with a cube welded in two ways by method 135, followed by an assessment of the performance of welds. The results of the evaluation are written down in the manual.
|
|
|
Use of thermographic methods for diagnostics of concrete bridges
Janků, Michal ; Hobst, Leonard (referee) ; Matula, Radek (referee) ; Cikrle, Petr (advisor)
This dissertation is focused on the research of the applicability of the thermographic method in the diagnosis of concrete bridges in the Czech Republic. The theoretical part characterizes selected defects of concrete structures and the principle of their detection. The practical part describes the measurements made in the laboratory on the test specimen and the field on the concrete bridge. Most attention is paid to infrared thermography, ground-penetrating radar and ultrasonic pulse-echo method. Based on the results of the dissertation, recommendations for the use of the thermographic test method in practice were developed.
|
|
|
Determination of the formwork strength of concrete using a Silver Schmidt hardness tester
Janka, Marek ; Kocáb, Dalibor (referee) ; Cikrle, Petr (advisor)
This bachelor thesis deal with the issues of nondestructive testing of the formwork removal strength of concrete. It works with two different compositions of concrete and for both of them, it determines the relation between compressive strength and surface hardness obtained by the SilverSchimdt hammer with mushroom plunger. It shows inappropriateness of ultrasonic impulse method to determine formwork removal strength. It compares obtained relations with each other and with the literature. The goal of this thesis is to utilize determined relations for verification of minimal requested formwork removal strength during construction.
|
|
| |
|
|
Non-destructive properties detection of concrete of prestressed beams
Mikulec, Jan ; Bílek, Vlastimil (referee) ; Cikrle, Petr (advisor)
The masers’s thesis is about the methods of non-destructive testing and about determining the properties of prestressed concrete. The first part pursues an introduction on the prestressed concrete, its essence and material properties. The next section describes the non-destructive diagnostic methods used in the practical part – the ultrasound impulse method, the resonance method and the rebound hardness test method. There are described destructive tests on the specimens for the calculation of the calibration. This is followed by a practical part, which describes the item tested - truss, its manufacturing, storage, and perform the test. Then search value are calculated from the test results and results are compared according to various procedures specified in the standards. The last section is devoted to the calculation of camber truss and loss of preload.
|
|
|
Design of instrument for the analysis of crack initiation and propagation
Šubrt, Stanislav ; Andrš, Ondřej (referee) ; Houška, Pavel (advisor)
The main goal of this thesis is to get an insight into a field of non-destructive testing using potential drop techniques that have nowadays become the standard not only in the fatigue and loading tests but also in the industry. These methods can serve to non-destructively and continuously measure material specimens, thickness, corrosion losses, deformations, spectroscopy and detection and analysis of crack geometry. They can help to identify materials and measure material changes over time. The second part of this thesis deals with designing the aperture for detection of cracks in steam and product piping using potential drop technique modified by Ing. Ladislav Korec, CSc. Last part deals with extensive testing, experimenting and evaluation of the aperture.
|
|
|
Non-destructive testing of welds
Šaloun, Jan ; Sigmund, Marian (referee) ; Kubíček, Jaroslav (advisor)
This thesis describes non-destructive testing (NDT) of fusion welds of metals. There are five fundament methods of NDT discussed in the theoretical part – visual and magnetic particle inspection, ultrasonic, radiography and penetrant testing. Principles of methods, examining procedures and their evaluations are described. The methods are compared with each other. In the experimental part of the thesis two samples of welding joints were welded and tested by selected methods. To verify correctness of the indicated defects, metallographic samples were made. At the conclusion practical results are compared with theoretical statements.
|
guest ::
