|
|
Virtual commissioning of the robotic completion of the shaft
Krůpa, Jiří ; Szabari, Mikuláš (referee) ; Bražina, Jakub (advisor)
This diploma thesis deals with the design and virtual commissioning of a robotic workplace for the assembly of an electric motor shaft. The theoretical part of the thesis summarizes the knowledge about virtual commissioning and briefly introduces the simulation program Process Simulate from the Tecnomatix software family. The practical part describes the design of a new robotic workplace for pre-assembly of rotors, which is to replace the three workplaces of manual assembly. The design was made on the basis of an analysis of the current state of the manual assembly process and using multicriteria analysis. The next section describes the process of creating a simulation model in the Process Simulate program and creating a PLC control program for a robotic cell in the TIA Portal program. The work also contains a proposal for the visualization of the HMI control panel using the HMI Template Suite. At the end of the work is a description of the virtual commissioning itself.
|
|
|
Application of industrial robots in 3D print
Krůpa, Jiří ; Vetiška, Jan (referee) ; Bražina, Jakub (advisor)
This bachelor thesis deals with the application of industrial robots in 3D printing, especially FDM technology. The introductory part of the thesis describes the basic types of additive technologies usable for robotic 3D printing. The next chapter describes some unconventional methods of 3D printing, using more than three degrees of freedom. The work also presents a comparison of conventional 3D printers with robotic manipulators and an assessment of the suitability of robots for 3D printing. At the end of the work are the necessary hardware and software peripherals for the modification of the robotic workstation for printing FDM technology. The ABB Robotstudio program was chosen as the software peripheral for the work example, and the procedure for creating the control code is described in the relevant chapter. This work also contains the design of printinghead for FDM technology.
|
|
|
Virtual commissioning of the robotic completion of the shaft
Krůpa, Jiří ; Szabari, Mikuláš (referee) ; Bražina, Jakub (advisor)
This diploma thesis deals with the design and virtual commissioning of a robotic workplace for the assembly of an electric motor shaft. The theoretical part of the thesis summarizes the knowledge about virtual commissioning and briefly introduces the simulation program Process Simulate from the Tecnomatix software family. The practical part describes the design of a new robotic workplace for pre-assembly of rotors, which is to replace the three workplaces of manual assembly. The design was made on the basis of an analysis of the current state of the manual assembly process and using multicriteria analysis. The next section describes the process of creating a simulation model in the Process Simulate program and creating a PLC control program for a robotic cell in the TIA Portal program. The work also contains a proposal for the visualization of the HMI control panel using the HMI Template Suite. At the end of the work is a description of the virtual commissioning itself.
|
|
|
Application of industrial robots in 3D print
Krůpa, Jiří ; Vetiška, Jan (referee) ; Bražina, Jakub (advisor)
This bachelor thesis deals with the application of industrial robots in 3D printing, especially FDM technology. The introductory part of the thesis describes the basic types of additive technologies usable for robotic 3D printing. The next chapter describes some unconventional methods of 3D printing, using more than three degrees of freedom. The work also presents a comparison of conventional 3D printers with robotic manipulators and an assessment of the suitability of robots for 3D printing. At the end of the work are the necessary hardware and software peripherals for the modification of the robotic workstation for printing FDM technology. The ABB Robotstudio program was chosen as the software peripheral for the work example, and the procedure for creating the control code is described in the relevant chapter. This work also contains the design of printinghead for FDM technology.
|
|
|
Communication strategy of Greenpeace CZ
Krupa, Jiří ; Říhová, Vladimíra (advisor) ; Šmíd, Jan (referee)
The main aim of this paper is to create image of selected campaigns of Greenpeace CZ. With this image is author trying to achieve certain platform to decide which of the selected campaigns are the most effective in context of its communication strategies. The way this is decided is first to find supporting facts in theoretical part to be able to find support for this question. In the second part the analysis of selected campaigns is made and used communication tools are found. This is put together in the third part, where the most effectively communicated campaign is found. Authors own contribution is provided by finding those results. Thanks to the information's discovered in the first and second part the author could made this model to answer defined goal -- how effectively Greenpeace CZ campaigns are communicated.
|
guest ::
RSS feed.