|
|
Design VUT 022 Aircraft with Jet Engine according to CS-22 Regulation
Matěják, Vladimír ; Popela, Robert (referee) ; Juračka, Jaroslav (advisor)
The diploma thesis deals with the design, load calculation and stress analysis of a composite wing construction of an airplane based on the construction of the airplane VUT 001 Marabu in order to fulfil conditions of CS-22 specifications. As a part of the thesis are basic mass, moment and aerodynamic characteristic of the airplane analyzed. Also the modification of the center part of the fuselage is designed in order to enable a jet engine instalation inside the construction.
|
|
| |
|
| |
|
|
Numerical analysis of bio-mimetic concept for active flow control on wing surface
Čermák, Jakub ; Navrátil, Jan (referee) ; Popela, Robert (advisor)
V této diplomové práci je provedena optimalizace profilu křídla vybaveného elastickou klapkou umístěnou na horní straně profilu. Optimalizační proces je proveden s vyžitím CFD prostředků, konkrétně URANS metody. V prvních kapitolách je popsána historie vývoje křídla vybaveného pohyblivými klapkami. Práce pokračuje popisem a zdůvodněním volby numerické metody. Vytvoření geometrie a výpočetní sítě je krátce popsáno. V práci je také prezentována validace a verifikace dané výpočetní metody. Případová studie je zaměřena na profil LS(1)-0417mod vybavený 20%, 30% a 40% dlouhou, pevnou kalpkou na různých úhlech náběhu. Aerodynamická účinnost společně s proudovým polem je analyzována. Je provedena nelineární pevnostní analýza s využitím MKP programu za účelem vyhodnocení ohybové tuhosti a deformovaného tvaru elastické klapky tak, aby byly splněný podmínky nutné pro automatické vychýlení.
|
|
|
Aerodynamic analysis of low orbit launcher
Fojtl, Michal ; Navrátil, Jan (referee) ; Popela, Robert (advisor)
Master’s thesis deals with aerodynamic heating of launch vehicle during ascent phase by using CFD simulation. Ascent trajectory and payload fairing geometry is design using data of existing small launch vehicles. Critical flight regimes are identified using 2D calculations, and in these regimes analysis is performed by axially symmetric simulations. Simulation results are compared to values obtained from theoretical and semi-empirical calculations.
|
|
|
Aerodynamic analysis and design modifications of L 410 NG aircraft wing-fuselage junction
Derevjanik, Šimon ; Pejchar, Jan (referee) ; Popela, Robert (advisor)
This thesis deals with CFD analysis of a wing-fuselage junction on L410NG airplane. Possible modifications are proposed as well. Calibration problem solved in the introduction serves as a pathway for validation of the results and gives insight into the CFD methodology. The main part analyses the airplane's flow field and shows the details of the modelling process. Description of the computing network followed by final evaluation is presented. Next part is devoted to the creation and aerodynamic analysis of the modified geometry. Final part of the work compares both basic and modified geometry.
|
|
|
Modern flow visualization techniques
Pištěcká, Kateřina ; Koutník, Tomáš (referee) ; Popela, Robert (advisor)
The subject of this bachelor thesis is an overview of the flow visualization methods applied in the wind tunnels and fly tests. An overview of flow visualization methods is presented in the first part of the work. The particular methods are presented and evaluated with respect of its complexity, requirements on the instrumentation and expanses. The pros and cons are mentioned for each method finally. The second part of the work deals with selection of the flow visualization method suitable for application in the wind tunnel of the Aeronautical department of the VUT Brno.
|
|
|
High performance paraglider aerodynamic optimization
Grim, Robert ; Navrátil, Jan (referee) ; Popela, Robert (advisor)
This thesis is focused on the aerodynamic analysis of the competition paraglider wing. Drags of the particular wing parts are divided into chapters. The aim was to get a grasp of sizes of the individual components drags in relation to the entire assembly. In the first instance, a 2D profile and then the entire configuration of the 3D wing was analyzed. After the evaluation, some power reserves were detected in an airfoil and so the airfoil shape was optimized. After the optimization of the individual components, the CFD calculation was used again. At the end, geometry changes were evaluated.
|
|
| |
|
|
Small UAV parachute recovery system design
Pejchar, Jan ; Jebáček, Ivo (referee) ; Popela, Robert (advisor)
The thesis is focused on the small UAV’s rescue system design. The thesis is divided into related sections reflecting the design process. The first part deals with general problems of parachute equipment. Another part is evaluating critical situations in manual and autonomous control of the airplane. The deceleration device is based on this critical situations as well as the calculated structure loading. Next is the description and evaluation of experiments to verify the performance of modern parachutes. The thesis also includes a simplified proposal ejection mechanism designed in 3D software and documentation of the of model aircraft construction for testing and predicting behaviour in autonomous flight mode.
|
guest ::
