|
|
Controlled heating of Composite Material
Fajkus, Martin ; Macháň, Ladislav (referee) ; Šteffan, Pavel (advisor)
The supposed thesis considers problem of heating of composite material for outdoor application. Basement of thesis is analysis of submitted sample of composite material. Measured values of composite material were compared and evaluated and than acceptable samples were choosen for next application. Part of thesis is creation of measuring software for analysis of sample. Other part of thesis is realization of equipment of control unit for heating of composite material. Control unit makes it possible to regulate heating and to set up parameters from computer.
|
|
|
Influence of thermal processing to microstructure of various steels
Kocman, Lukáš ; Havlík, Petr (referee) ; Štěpánek, Roman (advisor)
This bachelor thesis deals with the heat treatment of steel, especially measuring the influence of individual heat treatment technologies on changes in the microstructure of steels. The theoretical part of the work presents alloys of iron and carbon, furthermore describes their phase transformations in the solid state, particularly the transformation diagrams of steels. In another part of theoretical part, the basic heat treatment technologies and their influence on the mechanical properties and microstructure of steels are described. The experimental part deals with the preparation of metallographic samples and presents results of examining the microstructure and measuring the hardness of individual samples. At the end of the work the synthesis of the theoretical part and results of the experimental part is used for the partial and overall evaluation of the influence of heat treatment on the microstructure of steels.
|
|
|
Influence of tempering to dimension of two-component polycarbonate molding
Svobodová, Hana ; Dočekalová, Julie (referee) ; Sedlák, Josef (advisor)
This bachelor thesis is focused on changing the dimensions of two-component polycarbonate holding during the tempering process. In the thesis there is a complete description of the production of the external lens for the automobile headlight. The experimental part is focused only on the part of the process, the tempering. The subject of the experiment is to determine the effect of the temperature in the tempering furnace and the effect of the used slats on the dimensions of the polycarbonate molding. 3D measurements are used to evaluace dimensionality. The influence of the slats is examined with free types of slats.
|
|
|
Tempering of 3D FDM printed parts
Macháček, Jan ; Koppová, Aneta (referee) ; Zemčík, Oskar (advisor)
The bachelor thesis covers 3D printing methods, parts of a 3D printer, materials used to 3D print and the theoretical part od tempering 3D printed parts. The practical part consists of designing the experiment, results of tests and an econimical a functional evaluation.
|
|
|
Heat treatment of tool steels
Tobolík, Stanislav ; Pacal, Bohumil (referee) ; Molliková, Eva (advisor)
This thesis deals with the properties of ledeburitic chrome-vanadium tool steel after heat treatment. Theoretical part contains charakterization of ledeburitic steels, the posibility of manufacturing and heat treatment. There are also briefly describes the principles of the test methods, which were used. The practical part is focused on describing the results of 12 sample groups, with different heat treatment. The results are compared in the final discussion.
|
|
|
Methods of secondary influencing steel and steel ingot structures
Šprta, Pavel ; Pernica, Vítězslav (referee) ; Blažík, Petr (advisor)
This bachelor’s thesis deals with heat treatment of steels. Iron-carbon diagram and basics of heat treatment are described in the beginning of the literature search. Further the thesis focuses on austenitization and changes during decomposition of austenite. Introduction to transformation diagrams and their use is also included in this thesis. At the end the thesis focuses on description of individual heat treating methods. The experimental section contains metallographic analysis of 4 samples made of low carbon steel.
|
|
|
Low Temperature and Cryogenic Treatment of Casehardened Parts
Bílková, Lenka ; Juliš, Martin (referee) ; Kouřil, Miloslav (advisor)
This work deals with the assessment of the influence of low-temperature treatment on the structure and properties of casehardened surface layer of parts. The objective was to assess whether low-temperature treatment is sufficient, insufficient, or unnecessary for the given purpose. Gears which form a part of Zetor tractors gear boxes were used as samples. Thirteen pairs of frozen and non-frozen samples were used; they were taken from production batches throughout 2007, their hardness was assessed and furthermore, the experiment itself, freezing casehardened and hardened samples to different temperatures reaching as low as -196°C, was carried out. A moderate increase in hardness was registered with the majority of the frozen samples, which proved the effectiveness of the low-temperature treatment.
|
|
|
The controlled heating of composites materials
Fajkus, Martin ; Havlíček, Tomáš (referee) ; Šteffan, Pavel (advisor)
Expected work solves problem of controlled heating of composite material for outdoor application. Basement of work is analysis of submitted concrete specimen of composite. Then I find out influence of direct and alternating voltage on submitted specimen and I choose method of measurement. Whereas I chose correct method of measurement, I could measure all specimens. From comparing I chose specimen of composite material, which are suitable for a next application. For chosen specimen of composite material I designed control unit for heating and tempering. The control unit was designed according to their parameter.
|
|
|
The Influence of Heat Treatment on the Structure and Mechanical Properties of Tool Steels
Tobolík, Stanislav ; Němec, Karel (referee) ; Molliková, Eva (advisor)
This bachelor thesis deals with the properties of tool steels after heat treatment. The theoretical part describes the properties of iron and its alloys with carbon, and an overview of the use of steel. It is also discussed in detail the heat treatment of tool steels and manufacturing process analysis and metallographic sample. In the last part of the bachelor thesis there are described the mechanical testing of metals. In the practical part it is tested structure and mechanical properties of the selected tool steels for two types of heat treatment and the results are compared with the requirements imposed on it.
|
|
|
Heat treatment of formed parts
Leška, Radim ; Jopek, Miroslav (referee) ; Lidmila, Zdeněk (advisor)
In the research part, the bachelor thesis deals with forming, the mechanism of plastic deformation and steels used for forming. It also describes the principles of heat treatment, specifically the methods used in the preparation of semi-finished products, pressings, and forgings, i.e., annealing, hardening, and tempering. In the practical part, several experiments were performed on C45 steel. The first of them verified the effect of strain hardening after compaction, the others were focused on recrystallization, full annealing, hardening, and tempering. The effect of deformation and heat treatment was assessed in terms of hardness, which was measured by the Vickers hardness test.
|
guest ::
