|
|
Testing and measurement EMC
Bartoň, Jiří ; Hoder, Karel (referee) ; Havlíková, Marie (advisor)
This bachelor thesis is focused on a problem field of electronic compability as a whole - both the technical and biological side. Each legislative requirements and regulations of EMC are analyzed in this thesis Part of thesis is to design a test procedure for verification of EMC information technology equipment (ITE). Practical work is devoted to an overview and implementation of EMS according to the applicable test standards in the laboratory measurement of the Institute of Electrical Control and Instrumentation FEEC and services in the Research Institute in Brno.
|
|
|
Modelling of data transfer over LV and HV power lines
Feit, Kamil ; Koutný, Martin (referee) ; Mišurec, Jiří (advisor)
In this thesis work I am attending to matter of interference in transmissions by Power Line Communication. The goal of this thesis is to determine the impact of interference on the signal, which transmits data. This is achieved by implementing an interfering signal to the power line with the generator. There will also be an analysis of a way how to implement interference to the power line. After the implementation of interference I will monitor the impact of interference on the ongoing data transfer between the modems. At the end of this thesis is dissected the impact of interference in the transmission of data, with depicted transferred signal. Next is shown how the transferred signal affects communication between the modems and what happens when the interference
|
|
|
Measurements of electromagnetic interference in anechoic and semi-anechoic chambers
Deneš, Roman ; Růžek, Václav (referee) ; Dřínovský, Jiří (advisor)
This thesis is focused on a detailed analysis of the mechanisms of electromagnetic wave propagation in anechoic chambers. The analysis takes into account the influence of the measurement distance, setup of anechoic chamber and other parameters. Furthermore, the work deals with a validation of both types of anechoic chambers and examines the impact of selected parameters on the measurement results. Based on the theoretical analysis and practical measurement, the comparation between semi and fully anechoic chamber, or a three and ten meter measuring distance was made. This thesis also contains a detailed analysis of sources of the uncertainty.
|
|
|
EMC Test laboratory for low voltage circuit breaker
Vejtasa, Leoš ; Dřínovský, Jiří (referee) ; Dohnal, Petr (advisor)
Nowadays there are electronic systems almost in every new device. They are emitting and receiving electromagnetic interferences. The safety levels for circuit breakers are also increasing. Because of these issues the circuit breakers must work properly also in areas filled by electromagnetic interference. This thesis describes the issues of electromagnetic susceptibility of the circuit breakers.
|
|
|
Monitoring interference in the mains supply
Jirčík, Zdeněk ; Kubánek, David (referee) ; Zeman, Václav (advisor)
This semester thesis describes design of electronic device adapted to monitoring of mains supply. Theoretical parts describes mains supply analysis, communication and management of files to memory. Next part is design electronics blocks and their cooperation. There are description of mains analyzer prototype and it’s parts and functions. Prototype was submitted to test measurement.
|
|
|
Remote control of low voltage motor circuit - breaker
Brtnický, Jiří ; Musil, Vladislav (referee) ; ABB, Stanislav Korčián, (advisor)
The master´s thesis describes the design of the remote control, which is used as accessories for motor circuit-breaker. The work is based on the concept of control realized in the bachelor´s thesis. Master’s thesis contains a literature review of management method stepper motors with integrated circuits. standards relating to the control and switching low voltage devices were rehearsed. It was compiled schema of an entire unit after designing optimal control section of a stepper motor with integrated circuits, which consists of four parts (power supply, power section for driving an coils of stepper motor, control section and section for driving external devices). Design and realization of PCB are based on compiled schema, PCB was mounted with components and final PCB was recovered. The last part of thesis is about verification a functionality with using measurement of a prototype parameters.
|
|
|
Virtual Measurement System for the Anechoic Chambers
Váško, Ondřej ; Soldán, Josef (referee) ; Dřínovský, Jiří (advisor)
Master thesis examines a selected part of electromagnetic compatibility. In this work, there is theoretically discussed how electromagnetic interference appears and how is spread through free space environment. To eliminate ambient interference signals, the measurements have been performed in anechoic chamber where the undesirable interference signals were suppressed. In the thesis, there are also described parameters of EMI receivers and limits of electromagnetic interference. The description of calculations of the antenna height for finding maximum intensity of electric field strength for standard measurement distance has been made. For proposed transformed measurement distance, calculations of intensity electric field with addition of parameters measuring antenna and object under test were performed. Correction curves for conversion intensity electric field have been obtained as the result.
|
|
|
Modulations in PLC systems
Procházka, Vít ; Kouřil, Jiří (referee) ; Krajsa, Ondřej (advisor)
The bachelor thesis describes principles and methods of Powerline Communications, practical usage possibilities both in industrial applications but mainly in broadband systems that may represent promising competition to conventional broadband access, e. g. xDSL connections without the need of new wiring, WIFI etc. The thesis also focuses on problems that can occur in the communication channel from the view of electromagnetic compatibility and assorted interferences. The 50 Hz frequency electric network (60 Hz in the USA) was not designed for data signal transmission, problems may arise mainly at higher frequencies and broadband communication. It is necessary to implement methods which enable transfer of information signal through a communication channel with minimalization of problems such as interference, cable attenuation, electromagnetic compatibility, bit error rate (BER), etc. Furthermore, currently used modulation principles and their characteristics are described, such as spread spectrum modulation DSSS, FHSS, traditional OFDM, alternative modulations FMT and DWMT with filter banks. The last chapter of the bachelor thesis features models of particular modulations created in the Matlab-Simulink program and the conclusion presents advantages and disadvantages of their implementation in PLC systems.
|
|
|
Methods of printed circuit board design
Cirkovský, Jaroslav ; Vrba, Kamil (referee) ; Herencsár, Norbert (advisor)
The main purpose of my bachelor thesis was to acquaint with issues of printed circuit boards and to create multimedia videos. The first part deals with questions of the accuracy, miniaturization and applied cases with different outlets. Following chapters dissert on electromagnetic compatibility from the view of basic rules, which have to be observed in order to reach the best functionality of the printed circuit board. There are also other issues - components increasing the reliability of printed circuit board and the comparing of methods of printed circuit board design. The final part of my bachelor thesis discusses outputs which are necessary in practice. This includes technical and design documentation and the technology of production the printed circuit. The last chapter describes created multimedia utilities which help us with printed circuit boards design via the program Eagle.
|
|
|
EMD instruments and electromagnetic mmunity
Mikula, Dalibor ; Buchta,, zdeněk (referee) ; Havlíková, Marie (advisor)
The work deals with implantable devices and possibilities of interference of elektromagnetic field. At first, the electromagnetic compatibility is discussed. Basic terms are explained, followed by insisting on resources of possible distrurbing of implantable devices and standards dealing with this issue. Furthermore, short chapter about devices affecting function of implantable devices is introduced. It means devices which patients with implantable devices may meet in common life, as well as devices used in common life, also devices used jn medical environment. In the next part, measuring process of electromamagnetic effect in working compartment of FN Brno magnetotheraphy and elektrotheraphy is devised. There is a concept of measuring card thanks to which impulses of implantable devices are measured. Finally, a description of measuring on implantable devices in FN Brno. MIKULA, D. EMD instruments and electromagnetic immunity. Brno, 2009. 74 s. Master’s thesis in Brno University of technology on faculty of elektrical engeenerig and communication. Supervisor Ing. Marie Havlíková , Ph.D.
|
guest ::
