|
|
Development of Production Management Support of an Information System
Hladký, Miroslav ; Tengler, Jiří (referee) ; Videcká, Zdeňka (advisor)
This thesis deals with the proposal to support production management information system in the particular company. Based on theoretical knowledge and analysis of the current state of the company and its surroundings, the proposal supports production management information system. The thesis includes the level of strategy, tactics and operations and areas of the planning, organizing, management and control. Proposals should lead to greater effectiveness and efficiency in the processes related to production and thereby to achieve higher profits.
|
|
|
Logistics of Material Flow in Manufacturing Company
Šromová, Lenka ; Bičanová, Lenka (referee) ; Juřica, Pavel (advisor)
The bachelor thesis focuses on the description and analysis of the production and logistics system in a company PEVEKO, spol. s r.o. At first it explains the general concepts of the issue of logistics and improvement of processes, the next part it analyzes the actual situation in the company´s production. The final part contains the suggestions that could advance material flow and reduce the waste caused by redundant material or employee transfer.
|
|
| |
|
|
Management of Logistic Flow in Manufacturing Company
Fialová, Oksana ; Něnička, Jakub (referee) ; Juřica, Pavel (advisor)
The bachelor thesis focuses on the description and analysis of the logistics flow in manufacturing company PP Tuning Racing Parts s.r.o. At first it explains the general concepts of this issue. In the next part it analyzes the actual situation in the company. In conclusion it summarizes all the data and suggests measures that could improve the situation of logistics in the company.
|
|
| |
|
|
The Proposal to Improve the Selected Process in the Company
Kunc, Aleš ; Videcká, Zdeňka (referee) ; Varjan, Matúš (advisor)
Bachelor thesis is oriented on analysis of production processes in the company ČeMeBo s. r. o. Through detailed analysis of defined production area the recommendations are offered for potential improvements of current processes. Chosen area is directly supported with simulation model created using computer software Witness. Conceptual model serves author as source of practical experiences with simulation modeling and its verification with real process. This work also concerns modern concepts of production management, information systems and production processes modeling problems.
|
|
| |
|
|
Shop Floor Scheduling in Discrete Parts Manufacturing
Vágner, Ladislav ; Boček, Aleš (referee) ; Simeonov, Simeon (advisor)
Master´s thesis analyses the current state of the production scheduling in a manufacturing company in the automotive industry. It describes the setup system management of the module Advanced Production Planning by Helios Orange program, which company uses. This thesis introduces a new process of order and describes procedures for control of this module. Two essential steps of this new process were tested – creation of production orders and scheduling of production batches. In the end of the master´s thesis there are estimated financial savings after the implementation of the new process production scheduling.
|
|
|
Operations proposal for the packaging of auto lights used in private vehicles
Palacký, Vladislav ; Neužil, Karel (referee) ; Kubík, Roman (advisor)
The aim of this master thesis is to propose a new operation arrangements for the packaging of auto lights used in private vehicles. For this solution had been used a theoretical knowledge from large areas of logistics, production management, lean manufacturing methodologies, and even the practical experience and knowledge of the particular conditions of the company. Conducted research has detected a critical areas in the company and there was designed a system to remove them. The results of this study allow implementing certain measures, which will improve the company efficiency and increase its competitiveness.
|
|
|
Study of Process Control in Selected Products
Růžička, Pavel ; Bednář, Josef (referee) ; Jurová, Marie (advisor)
The thesis focuses on the process of production of castings in the company ŽĎAS, a.s. and its methods for implementing customer's requirements. The goal was to create a Work Flow diagram of technical preparation of production based on the company's internal directives. The next step was to compare it with the actual situation represented by a case job and to make a conclusion. The customer's requirements for the case production order included increased level of control and purchasing weld-on parts. The incorporation process for these requirements was not described by the original Work Flow and was the subject of its new revision. For its better practical application the Study contains business and organizational structures of ŽĎAS, a.s.
|
guest ::
