|
|
Cable-supported bridge
Adler, Filip ; Glovina, Filip (referee) ; Nečas, Radim (advisor)
The subject of this master thesis is to design a pedestrian bridge supported by cables. There are three variants of studies created for this case and for most suitable one, all documentations were produced. The primary focus of this work is on static design solution with an output of several drawings. Static model for results from load cases included construction stages and was created in Midas Civil. Design and checks were performed by hand calculations, complemented by checks of several sections by IDEA StatiCa software. Analysis and calculations are compliant to up-to-date codes and respect the fundamentals of analysis due to limit states.
|
|
|
Control and monitoring unit for optical link station
Ovčáček, Martin ; Kolka, Zdeněk (referee) ; Prokeš, Aleš (advisor)
The aim of Master's thesis "Control and monitoring unit for optical link station" is design of hardware and software of unit, which provides remote control and data transfer through Internet. It is required monitoring and setting analog parameters of optical link station by web service. It includes description of Ethernet and net protocols. The core of unit are microcontroller C8051F120 and ethernet controller CP2200 made by Silicon Laboratories.
|
|
|
Design of linear motor with permanent magnets
Čech, Jan ; Bulín, Tomáš (referee) ; Knebl, Ladislav (advisor)
The first part of this thesis deals with the study of linear motors. The introduction of the thesis deals with the brief description of the linear motor, including its accessories. This part explains principle of linear motors, their general advantages and disadvantages. The next section contains an overview and division of the currently used linear motors. Each type of currently used linear motors is briefly introduced and also its principle and characteristics are described, including its specific application. The second part of the thesis deals with the design of an equivalent magnetic circuit model of a linear iron-core linear motor. Hereafter, the proposed design will be used to simulate the distribution of magnetic flux in the linear motor. The evaluated flux-density distribution in the air gap is later compared with the results obtained with finite element method. The thrust is then calculated from the flux-density and the estimated value is compared with the value listed in datasheet.
|
|
|
Model of a prefabricated footbridge for teaching
Gaidos, Daniel ; Koláček, Jan (referee) ; Strnad, Jiří (advisor)
The subject of this thesis was to design a test model of a foot bridge built out of sets of blocks, coupled by prestressing monostrands into one beam. Created model will serve as a test model during the training of machinists on tensioning equipment. Static model for results from load cases was created in Scia Engineering 20.0. Assessment and dimensioning were solved in the MS Excel program. The structure was assessed for the limit state of load-bearing capacity and serviceability. Analysis and calculations are compliant to up-to-date codes and respect the fundamentals of analysis due to limit states.
|
|
|
Model of computer network in MATLAB/SIMULINK environment
Zedníček, Petr ; Zeman, Václav (referee) ; Kolka, Zdeněk (advisor)
The bachelor thesis deals with simulation of TCP protocol behaviour in Wireless optical environment. The thesis examines the various parameters of the protocol and evaluates their response to the transmission speed. The key objectives of the thesis are the introduction to the problems of communication, specially the description of the transport layer architecture, TCP / IP and congestion management mechanism NewReno. A large part of the thesis is devoted to modelling communication points and a model of optical wireless connections. The results will be applicable to create a new communication protocol for Wireless optical environment.
|
|
|
Reconstruction of the Building for Storage
Heger, Petr ; Buchta, Stanislav (referee) ; Hron, Lukáš (advisor)
The subject of this bachelor’s thesis is to design the extension of the steel structure of the storage hall. The task is to double the platform area from 18 x 18 m up to 36x18 m with the height of 7,5 m. It is required to use as much of existing profiles as possible. The structure is located in Znojmo. The original roof structure is made of truss girders with the segmently curved lower girdle. The span of main frame is 18 m and the axial distance of main frames is 6 m. All girders are pinned. In extended structure is used the plate girder. Spatial rigidity of the structure is made by wall and roof bracing. The static calculation of main load-bearing elements including joints and specific details was made for the structure. The technical report and drawings were specified by the supervisor. For design of the structure were used valid standards ČSN EN.
|
|
|
Suspension footbridge over the river Bečva
Sobková, Sára ; Šopík, Leonard (referee) ; Nečas, Radim (advisor)
The subject of this thesis is the design and assessment of a suspended footbridge for pedestrians over the Bečva River. Three variants of the crossing were created. The va-riant with a suspension structure was selected for detailed design. The chosen pede-strian footbridge is composed of two suspension cables supported by an inclined py-lon, anchored by a set of six anchoring cables. The design of the structure relied on finding the ideal geometry of the suspension cables. The computational model was created in the ANSYS Mechanical APDL 2023 R2 software. For the analysis of the deck in the transverse direction, model was created in the SCIA Engineer 21.1 software. The construction was assessed for ultimate limit state of serviceability and load-bearing capacity according to applicable standards, and a dynamic analysis was performed. The work includes clear and detailed drawings and visualizations.
|
|
|
Industrial state indicator
Růžička, Zdenek ; Štohl, Radek (referee) ; Bradáč, Zdeněk (advisor)
Diploma work deals with industrial display systems, indicators and their proposal. These systems are used everywhere that is necessary to mediate transmission of information. Own proposal of indicator is very specific and depends on given application and used display. In practice there is possible to use a few types of displays but in this diploma work there are used only sedmisegmental and matrix. Common component of proposal is microcontroller. No less significat and important part of the proposal is a choice of interface and communication protocol. The correct choice of hardware that is completed with software we will obtain complete status indicator.
|
|
| |
|
|
Cable-supported pedestrian bridge
Knotek, Jan ; Brtáň, Stanislav (referee) ; Nečas, Radim (advisor)
The subject of this diploma thesis is design a cable-supported pedestrian bridge. Three different variants of the solution were created for the design. For detailed processing, variant no.2 was chosen - a suspended bridge with a pylon in the middle of the span. The main task is the static design of the supporting structure. The model for the lengthways is created in ANSYS. The SCIA engineer was used to solve crosswise. The assessment and dimensioning was done according to the limit state principles and valid standards.
|
guest ::
