|
|
Class AB audio amplifier for two satellites and subwoofer
Cupák, Jan ; Brančík, Lubomír (referee) ; Kratochvíl, Tomáš (advisor)
This bachelor’s thesis deals with design of AB class audio amplifiers. Further more it deals also with other functional blocks, e.g. preamplifier, tone equalizer and active crossover. Outcome of this work is a complete solution of the amplifier with it's simulation. In final solution is also included scheme of a high quality power supply unit, speaker protection and heat sinks for high performance transistors. In this project is also included a solution of task about optimal mechanical arrangement of the single parts in the case of this amplifier. This thesis contains results of measurement and photo document of functional prototype.
|
|
|
Design of class-D audio power amplifier
Fiala, Roman ; Götthans, Tomáš (referee) ; Brančík, Lubomír (advisor)
This semestral thesis describes class D low frequency power amplifiers and design of specific 2x100W class D power amplifier. The designed amplifier contains a second order sigma-delta modulator in which the quantization is controlled only by the delay of modulator components. This design does not include the clock generator which usually controls the quantization in sigma-delta modulators. This semestral thesis also includes design of a switched-mode power supply for the power amplifier and for the preamplifier. The PSpice program has been used for the design and verification of some sections of circuits. All designs have been built. Also basic parameters of completed circuits were measured.
|
|
|
Precision audio preamplifier for headset measurement
Šimek, Michal ; Balík, Miroslav (referee) ; Hanák, Pavel (advisor)
This thesis deals with microphone and headphone preamplifier for microtelephone and headset. The design shall meet the electrical interface requirements set out in ITU-T Rec. P.381(08/2012). The design includes a voltage converter, microtelephone bias and both a battery and an external power supply. In this work is also described the design of printed circuit board and the solution of a low noise in the whole circuit. The aim of this thesis is to design, built and embed the laboratory fixture into a metal box. Finally, measure the product on an APx525 audio precision analyzer.
|
|
|
Computer design of the small CATV
Sedláček, Jan ; Slanina, Martin (referee) ; Říčný, Václav (advisor)
Main task of this bachelor’s thesis is to create an interactive automatic programme for designing circuits of individual or small common television aerial. The first part of this document describes main conceptions distribution of television signals, parameters of coaxial cable and also some kinds of signals distortion. There are described some important mathematics formulas used for calculation of coaxial cable attenuation and carrier to noise distance important for computing function of programme. The second part describes a procedure of designing of television cable circuit of individual or small common television aerial and includes prototypal calculation of two real circuits and its comparison with results of computer calculation by which correct function of programme is verified. A part of this document is also made by detailed description of programme and its functions. Source code of created programme is included in the end of this document.
|
|
|
Mixing audio console with microphone preamplifier
Mecerod, Václav ; Šotner, Roman (referee) ; Kratochvíl, Tomáš (advisor)
Bachelor’s thesis on the theme "Mixing audio console with microphone preamplifier" deals with the design of an audio device for mixing signals from different sources. After a short theoretical introduction to issues mixing audio consoles, block diagram and circuit diagrams of each part are designed. These are redrawn into OrCAD Capture and using software PSpice simulations are performed. Configuration of the proposed mixing audio console is as follows: Two microphone preamplifiers with true differential inputs with switchable sensitivity, with the quad-band equalizer with tunable mid bands and adjustable delay. One line level input and one instrument input with three bands corrector. The output section consists of headphone and line level out.
|
|
|
Precise Audio Amplifier for Quality Listening
Janošík, Lukáš ; Šotner, Roman (referee) ; Kratochvíl, Tomáš (advisor)
This bachelor thesis deals with a design of quality audio preamplifier designed for high quality production. The typology of whole design emphasizes very important transmission properties, i.e. high signal-to-noise ratio, high separation of channel, low distortion, The content of the semestral thesis is an symetrical input, relay input switch, 5 band equalizer with bypass and symetrical output with active line driver.
|
|
|
SPM Methods Based On The Quartz Resonator Probes
Wertheimer, Pavel ; Sobotík, Pavel (referee) ; Číp, Ondřej (referee) ; Šikola, Tomáš (advisor)
The thesis is focused on development of scanning probe microscope systems, especially development and implementation of quartz resonator probes. The quartz resonator probes, compared to the standard silicon cantilevers, have several advantages. It is in particular their mechanical properties and possibility of direct electrical readout of the deflection signal. Due to the fact, the probes are easy to implement even into more complex SPM systems. The thesis deals with development of universal and open SPM control system electronics. The electronics consist of the commercial SPM control and oscillation units, the development of the other electronic parts (such as the high voltage amplifier and the preamplifier units) is described in the thesis. Further, the thesis reports on development of the qPlus UHV LT SPM microscope system that was carried out at Universität Hamburg. Part of it was development of the qPlus preamplifier able to operate at liquid helium temperature. The third topic of the thesis is the implementation of qPlus technology into the UHV VT SPM microscope suitable to operate in situ with a scanning electron microscope. The qPlus sensors and the universal UHV preamplifier were designed and manufactured. Test measurements were conducted on all of the developed systems.
|
|
|
Measurement system with preamplifier for calibration of vibration sensors
Kaštovský, Jan ; Doseděl, Martin (referee) ; Havránek, Zdeněk (advisor)
This thesis deals with the design and implementation of a preamplifier for vibration sensors with IEPE interface and also for vibration sensors with charge output. The thesis also deals with a modification of a computer application for a measuring system in LabVIEW. The thesis builds on the already implemented measuring system for secondary calibration of vibration sensors. The results of the secondary calibration of this system with the added preamplifier are compared with the results of a primary calibration.
|
|
|
Design of preamplifier for guitar effects generation.
Müller, Radek ; Kratochvíl, Tomáš (referee) ; Brančík, Lubomír (advisor)
The topic of my bachelor's project is preamplifier blueprint for creation of certain guitar effects. Output signal from an electric guitar is often modified for musician's needs. My objectives are to discover options of signal modifications, electronical solution of preamplifiers and final effect on sound character. My targets are to design and construct two chosen guitar effects, which will distort the output sigal from an electic guitar. Both wirings will be tested by computer simulation and then will be compared with real circuit wiring. Its necessary to box up the printed circuit board and place control and signal elements to accesible place.
|
|
|
Six-channel audio preamplifier with common volume control
Spilka, Benedikt ; Balík, Miroslav (referee) ; Hanák, Pavel (advisor)
The main aim of this bachelor thesis is to design and to construct a low-frequency six-channel preamplifier with remote and local control and with symetric and line input for up DPA223 low-frequency amplifier. The preamplifiers must have galvanic separation together. Its gain/amplification must be remote controllable from mute to 0dB and locally from 0dB to -20dB. Low distortion, noise and other parameters monitored in audio technics are important for the design.
|
guest ::
