|
|
Evaluation of an inspection program and overhauls for ZLIN 26 aircraft
Jančář, Milan ; Finda, Jindřich (referee) ; Augustin, Petr (advisor)
This bachelor´s thesis deals with ZLIN Z 26 Series Aircraft maintenance and repairs procedures. Even the name shows, that this theme is very demanding and extensive. My interest was to explain some maintenance procedures of these aircraft and offer changes of it. In the beginning of this thesis we can briefly learn history of the ZLIN Aircraft and particular Z 226 Series models. There are mentioned difference maintenance procedures, applicable on the planes thru the service life time. Inspection and overhaul procedures are described in details and for better understanding were attached drawings or photos. Following chapter deals with evaluation existing inspections and overhauls - maintenance – procedures. Optimization of the maintenance is part of the chapter fourth, where is described possible innovation of the maintenance check list. In the last, fifth chapter, of this thesis are mentioned possibilities of the ZLIN Aircraft life time prolongation, which is actually discussed because of some aircraft of this type series reached basic life time limit, without any serious fatigue airframe damages appears.
|
|
|
Machine tool Life Cycle
Mikulka, Tomáš ; Marek, Jiří (referee) ; Knoflíček, Radek (advisor)
The diploma thesis is focused on the determination of the life cycle state of the production machine. The thesis is divided into several chapters. First, the life cycle of the machine is defined, and the phrase used here is given. Subsequently, the work is devoted to maintenance, repairs and modernization of the production machine. Then there is a demonstration of Schaeffler Skalica's corporate structure and individual methods that determine the state of the machine's life cycle. In the next chapter, the machine is described and then the analysis is made for the current state of the machine. Then the analyses created are evaluated.
|
|
|
Revision of steam turbines and repair design
Grepl, Martin ; Trněný, Bohumil (referee) ; Fiedler, Jan (advisor)
The theme of this master thesis is the revision and repair design of the condensing steam turbine SST 600 in Bielsko-Biala. The thesis deals with the revision of the steam turbine and the repair design of the damaged parts, the overall analysis of the separation of the steam of the split plane and the calculation of the parameters for tightening the new screws. The master thesis is given for a specific case. The introductory part of the master thesis deals with a basic description of the repaired steam turbine. Subsequently, a review of individual disassembled parts is given and the scope of the repairs is stated. In the next part of this thesis are summarized the causes of the steam leakage of the dividing plane at the points of the cross section and in the area of the control stage. The last part deals with the sealing problem of the split plane and the related main part of the master thesis is the calculation of the tightening parameters of bolts in the turbine housing. Another aim of the master thesis is to create drawings of the lightening of the split plane on turbine house.
|
|
|
Control system overhaul of a granulate transport equippment
Minčík, Vojtech ; Benešl, Tomáš (referee) ; Fiedler, Petr (advisor)
This thesis deals with the design and overhaul of the suction system which was part of the extruder dosing device from Reifenheuser. The first part describes the pneumatic transport and its main parts and control possibilities. Moreover, the thesis deals with the evaluation of the original solution of the control system, its advantages and disadvantages, the requirements for modernization from the client and proposals for its implementation. The last part focuses on the selection of suitable components and subsequently on the final implementation of the entire project, which consists of the design of the switchboard, the creation of electrical documentation and PLC programming.
|
|
|
Generální oprava hydraulických nůžek na kovový šrot
RÝVORA, Daniel
The introduction of the literary part of the diploma thesis describes the issue of treatment and processing of metal waste, including the existing legislation that regulates the management of this type of waste. Furthermore, the non-destructive and destructive treatment of metal waste and its individual methods are explained. At the end of the literary part, the treatment of metal waste using hydraulic scissors for scrap metal and their description and division are described in more detail. In the practical part, the company GERA, export import, spol. s r.o., which uses hydraulic shears BONFIGLIOLI Squalo 1000 t. will be presented. At the end of the practical part, their overhaul will be described in detail.
|
|
|
Generální oprava motoru traktoru John Deere
PROKOPCOVÁ, Natálie
This thesis focuses on the engine overhaul of a John Deere 8320 tractor. It describes the falut that occurred on this tractor and also details the procedure of the entire repair and installation of the engine. Finally, there is an economic comparison of the cost of the repair by the procedure chosen in this thesis with the procedure if a new semiengine had been put in.
|
|
|
Control system overhaul of a granulate transport equippment
Minčík, Vojtech ; Benešl, Tomáš (referee) ; Fiedler, Petr (advisor)
This thesis deals with the design and overhaul of the suction system which was part of the extruder dosing device from Reifenheuser. The first part describes the pneumatic transport and its main parts and control possibilities. Moreover, the thesis deals with the evaluation of the original solution of the control system, its advantages and disadvantages, the requirements for modernization from the client and proposals for its implementation. The last part focuses on the selection of suitable components and subsequently on the final implementation of the entire project, which consists of the design of the switchboard, the creation of electrical documentation and PLC programming.
|
|
|
Machine tool Life Cycle
Mikulka, Tomáš ; Marek, Jiří (referee) ; Knoflíček, Radek (advisor)
The diploma thesis is focused on the determination of the life cycle state of the production machine. The thesis is divided into several chapters. First, the life cycle of the machine is defined, and the phrase used here is given. Subsequently, the work is devoted to maintenance, repairs and modernization of the production machine. Then there is a demonstration of Schaeffler Skalica's corporate structure and individual methods that determine the state of the machine's life cycle. In the next chapter, the machine is described and then the analysis is made for the current state of the machine. Then the analyses created are evaluated.
|
|
|
Revision of steam turbines and repair design
Grepl, Martin ; Trněný, Bohumil (referee) ; Fiedler, Jan (advisor)
The theme of this master thesis is the revision and repair design of the condensing steam turbine SST 600 in Bielsko-Biala. The thesis deals with the revision of the steam turbine and the repair design of the damaged parts, the overall analysis of the separation of the steam of the split plane and the calculation of the parameters for tightening the new screws. The master thesis is given for a specific case. The introductory part of the master thesis deals with a basic description of the repaired steam turbine. Subsequently, a review of individual disassembled parts is given and the scope of the repairs is stated. In the next part of this thesis are summarized the causes of the steam leakage of the dividing plane at the points of the cross section and in the area of the control stage. The last part deals with the sealing problem of the split plane and the related main part of the master thesis is the calculation of the tightening parameters of bolts in the turbine housing. Another aim of the master thesis is to create drawings of the lightening of the split plane on turbine house.
|
|
|
Evaluation of an inspection program and overhauls for ZLIN 26 aircraft
Jančář, Milan ; Finda, Jindřich (referee) ; Augustin, Petr (advisor)
This bachelor´s thesis deals with ZLIN Z 26 Series Aircraft maintenance and repairs procedures. Even the name shows, that this theme is very demanding and extensive. My interest was to explain some maintenance procedures of these aircraft and offer changes of it. In the beginning of this thesis we can briefly learn history of the ZLIN Aircraft and particular Z 226 Series models. There are mentioned difference maintenance procedures, applicable on the planes thru the service life time. Inspection and overhaul procedures are described in details and for better understanding were attached drawings or photos. Following chapter deals with evaluation existing inspections and overhauls - maintenance – procedures. Optimization of the maintenance is part of the chapter fourth, where is described possible innovation of the maintenance check list. In the last, fifth chapter, of this thesis are mentioned possibilities of the ZLIN Aircraft life time prolongation, which is actually discussed because of some aircraft of this type series reached basic life time limit, without any serious fatigue airframe damages appears.
|
guest ::
