|
|
Flow measurement
Dvořák, Roman ; Uher, Miroslav (referee) ; Beneš, Petr (advisor)
Bachelor´s thesis is elaboration an analysis accessible small gas station. The base was meet possibilities in measurement of small flows and of them choose optima suitable solution, eventually occupy fit pump and process device. After the introduced theoretical analysis in the first part is continuing the second part, where finds enumeration me choice elements station with presented cause selection. After realization all part of system was at last parts effected calibration and setting process device part gas station. Resulting solving was collated with commercially accessible systems small gas station.
|
|
|
Measurement and linearization unit for flow meters
Maštera, Martin ; Macho, Tomáš (referee) ; Petyovský, Petr (advisor)
Linearization display unit will receive pulses from a gear flow meter KRACHT whose frequency corresponds to a flow. The measured value is flow that nonlinearly depends on the temperature and viscosity of the medium. The dependency is described by calibration curves for each flow meter. The task of the diploma thesis is to design, implement, and verify the operation of the display unit, which calculates the actual flow rate from the input data (pulse rate, temperature, viscosity, and flow meter calibration curves). The device will contain a suitable user interface to display all measured values, inputs for connecting measuring sensors, and outputs for transmission of measured data. A part of the device will be a USB interface for configuration and uploading calibration curves from a PC application, which is designed by diploma student.
|
|
|
Data acquisition - LabVIEW
Jeřábek, Martin ; Zůbek, Tomáš (referee) ; Šedivá, Soňa (advisor)
The main objective of this work is to create a program for automatic operation of measuring test track. The track is used for multi-hole velocity probes calibration. Normalized orifice plate is used as measurement standard. The program requires the user to enter certain information, which are not measured directly e.g. the values of measuring resistors, static air pressure. After entering this information, measurement can be started. The measurements are carried out simultaneously on the both flowmeters and on the thermomether Pt 100. The actual density of flowing medium is calculated from the measured temperature. Because the measurement is parallel, the calibrated flowmeter can be calibrated during the measurement.
|
|
|
The system for measurement of little flow
Karásek, Eduard ; Prášek, Jan (referee) ; Adámek, Martin (advisor)
Diploma thesis solves how to create system for measurement of little liquid flows. The basic types of liquid flowmeter, which are possible used for measurement of little liquid flows, are described in the introduction part of thesis. The limit for little flow is often determined as flow 100 mg.min-1 and low. Second part of this thesis describes the ways of capillary production and practical experiments with them. Thesis is focused to thick film technology and LTCC technology. Next part of this work is solution of simple measuring unit for measurement of little flows less than 100 mg.min 1, which is controlled by microprocessor ATmega16. The measuring unit can be worked separately or can be connected to PC. The next possibility of flowmeter optimisation is summarized in end of thesis.
|
|
|
Proposal nozzle for measuring the air quantity of an internal combustion engine
Esterka, Ondřej ; Charvát, Pavel (referee) ; Štětina, Josef (advisor)
In this bachelor‘s thesis are mentioned emission standards, which apply to passenger cars, and the mixture-control system. There is also a research of volumetric and sectional flowmeters, suitable for measuring the flow volume of the air, including the principle of measuring the volumetric or mass flow. After that follows engineering design of Venturi tube for measuring the flow of the air through the chosen combustion engine. The design is based on the appropriate standard. There is also involved a welded assembly drawing of the Venturi tube, and a description, how to use the tube in a test room.
|
|
|
Development of mobile flowmeter
DITRICH, Vít
This thesis contains the description of well-known methods and principles dealing with the measurement of the flow-velocity of fluids. Furthermore, it contains the description of the development of the mobile flow-meter, including the realization and the technical description of the device. The thesis describes the advantages and disadvantages of the above mentioned flow-meter. The last part of the thesis is dedicated to the calibration of the device and to the possible practical use of the flow-meter.
|
|
| |
|
| |
|
| |
|
| |
guest ::
