|
|
Data collection from sensor units
Frkal, Pavel ; Verner, Lukáš (referee) ; Komosný, Dan (advisor)
This thesis deals with data collection from sensor units connected via 6LoWPAN standard (IEEE 802.15.4 standard), which uses simplified IPv6 protocol on the network layer. Featuring optimization makes this solution suitable for use in systems powered with chemical power supplies with a very low current consumption of both the sensor units and the control units. The thesis focuses on collecting data from sensor units that communicate on a star topology basis but it's also discussed possible usage of general topology, the end-station in such case works as active repeater and thus extend sensor network coverage without need of additional devices for wireless frames repeating or forwarding. It evaluates the realization of sensor networks created by both the actual data collection as well as specific technical parameters of used sensor boards. The practical part contains a specific application for gathering data from sensors present on the units and storing them in a relational database MySQL.
|
|
|
Smart socket for electrical parameters analysis with possibility of controlling connected appliances
Musil, Libor ; Krajsa, Ondřej (referee) ; Musil, Petr (advisor)
Thesis deals with the design of intelligent electrical socket. At the beginning of the thesis, there are described the characteristics of the distribution network in the Czech Republic and the ways of measuring these properties. The selected integrated circuit that realizes the measurement is described in detail. The third chapter deals with the current possibilities of power management, especially from the perspective of the distribution company and the concept of smart networks. The fourth chapter deals with the selection of communication interface suitable for smart socket as an element of smart home. The selected IEEE 802.15.4 standard and the microcontroller implementing the communication itself are described in more detail. The following part of the work is about design of the intelligent socket development board, on which the concept is tested and the design of the final hardware is described in this chapter. The last chapter describes the measurement results realized by the created device.
|
|
|
Wireless Mesh Protocol for FreeRTOS
Horák, Martin ; Krkoš, Radko (referee) ; Červenka, Vladimír (advisor)
Bachelor thesis aims to introduce in thereretical part operating principe of mesh network, their practical use, brief introduction of mesh protokol and standard 802.15.4. Also present a real-time operating systems, that can be used for programming applications based on real-time operating systems architecture. In practical part is to create several progres and made measurements of energy consumption and the number of cycles. Based on the results is found most appropriate implementation into the FreeRTOS. The final chapter is devoted to the overview of the achieved results, which are summarized in the tables.
|
|
|
Communication in ZigBee Networks
Majer, Tomáš ; Očenášek, Pavel (referee) ; Trchalík, Roman (advisor)
Now days, we are more often meet sensors and sensor networks, which are used mainly in industrial fields. In this master thesis my target is sensor network Zigbee and usage of it. Internal structure of communication frames of APS application layer is presented here in details as well, which is used for control of sensors inside of sensor network. Main purpose of this master thesis is to design and implement application gateway between Internet and sensor network ZigBee. I present possible solution of communication protocol for transport over the Internet and processing of it by ZigBee coordinator. Thesis is written in style suitable for practical solution and results of solution are presented on model situations, which include discussion about possible improvements.
|
|
|
Wirelles netowrok monitor
Slováček, Miroslav ; Fiedler, Petr (referee) ; Bradáč, Zdeněk (advisor)
This master´s thesis deal with designing of the system for ZigBee wireless network monitoring. In the first, treoretical part, is reader introduced to this wireless standard. Acquired informations are possible to compare with the simillar wireless standards. Next part of this document describes procedure of designing harward part of modular system - motherboard and scanning module. In this place is so discussion about component parameters, which are very needed to keep. One part of this discussion is about the problems with wrong component parameters. The last part of this master´s thesis is about software part of this project and so shows designed system in work.
|
|
|
Smart socket for electrical parameters analysis with possibility of controlling connected appliances
Musil, Libor ; Krajsa, Ondřej (referee) ; Musil, Petr (advisor)
Thesis deals with the design of intelligent electrical socket. At the beginning of the thesis, there are described the characteristics of the distribution network in the Czech Republic and the ways of measuring these properties. The selected integrated circuit that realizes the measurement is described in detail. The third chapter deals with the current possibilities of power management, especially from the perspective of the distribution company and the concept of smart networks. The fourth chapter deals with the selection of communication interface suitable for smart socket as an element of smart home. The selected IEEE 802.15.4 standard and the microcontroller implementing the communication itself are described in more detail. The following part of the work is about design of the intelligent socket development board, on which the concept is tested and the design of the final hardware is described in this chapter. The last chapter describes the measurement results realized by the created device.
|
|
|
Wireless Mesh Protocol for FreeRTOS
Horák, Martin ; Krkoš, Radko (referee) ; Červenka, Vladimír (advisor)
Bachelor thesis aims to introduce in thereretical part operating principe of mesh network, their practical use, brief introduction of mesh protokol and standard 802.15.4. Also present a real-time operating systems, that can be used for programming applications based on real-time operating systems architecture. In practical part is to create several progres and made measurements of energy consumption and the number of cycles. Based on the results is found most appropriate implementation into the FreeRTOS. The final chapter is devoted to the overview of the achieved results, which are summarized in the tables.
|
|
|
Data collection from sensor units
Frkal, Pavel ; Verner, Lukáš (referee) ; Komosný, Dan (advisor)
This thesis deals with data collection from sensor units connected via 6LoWPAN standard (IEEE 802.15.4 standard), which uses simplified IPv6 protocol on the network layer. Featuring optimization makes this solution suitable for use in systems powered with chemical power supplies with a very low current consumption of both the sensor units and the control units. The thesis focuses on collecting data from sensor units that communicate on a star topology basis but it's also discussed possible usage of general topology, the end-station in such case works as active repeater and thus extend sensor network coverage without need of additional devices for wireless frames repeating or forwarding. It evaluates the realization of sensor networks created by both the actual data collection as well as specific technical parameters of used sensor boards. The practical part contains a specific application for gathering data from sensors present on the units and storing them in a relational database MySQL.
|
|
|
Communication in ZigBee Networks
Majer, Tomáš ; Očenášek, Pavel (referee) ; Trchalík, Roman (advisor)
Now days, we are more often meet sensors and sensor networks, which are used mainly in industrial fields. In this master thesis my target is sensor network Zigbee and usage of it. Internal structure of communication frames of APS application layer is presented here in details as well, which is used for control of sensors inside of sensor network. Main purpose of this master thesis is to design and implement application gateway between Internet and sensor network ZigBee. I present possible solution of communication protocol for transport over the Internet and processing of it by ZigBee coordinator. Thesis is written in style suitable for practical solution and results of solution are presented on model situations, which include discussion about possible improvements.
|
|
|
Wirelles netowrok monitor
Slováček, Miroslav ; Fiedler, Petr (referee) ; Bradáč, Zdeněk (advisor)
This master´s thesis deal with designing of the system for ZigBee wireless network monitoring. In the first, treoretical part, is reader introduced to this wireless standard. Acquired informations are possible to compare with the simillar wireless standards. Next part of this document describes procedure of designing harward part of modular system - motherboard and scanning module. In this place is so discussion about component parameters, which are very needed to keep. One part of this discussion is about the problems with wrong component parameters. The last part of this master´s thesis is about software part of this project and so shows designed system in work.
|
guest ::
