|
|
Improving of hydraulic properties of swirl turbines
Kůrečka, Jan ; Veselý, Jindřich (referee) ; Haluza, Miloslav (advisor)
This diploma thesis describes design of blade geometry of swirl turbines with different blade row density for given parameters Q11 = 1,9 [m3s-1], n11 = 170 [min-1], H=2,5 m, and =0,8. Goal is to found out differences between designs with high count of runner blades and design with fewer blades. Comparison of computed characteristics of three, seven and nine bladed runners is given.
|
|
| |
|
|
FLow in cracs
Ocásek, Adam ; Veselý, Jindřich (referee) ; Haluza, Miloslav (advisor)
This Master’s thesis investigates the flow in sealing gaps of impeller within pumps and turbines. Sealing gaps are installed to improve the volumetric efficiency in this type of fluid machinery. Despite present extensive research this subject has not been entirely documented and the thesis’ aim is to improve our knowledge in this matter. At the beginning, the practical experiment is used in order to establish appropriate numerical description of flow in seals and to calibrate software FLUENT. In chapter five, the thesis analyses the influence of seal design on volumetric efficiency of pumps and turbines and defines its optimal construction to improve the efficiency. The thesis then examines the effect of rotor eccentricity on flow properties, flow rate and pressure distribution within the sealing gap. In the last section, through chapters six to eight, the flow results provided by numerical solution in FLUENT and selected analytical equations, or their modified forms, are being discussed. The degree of correspondence between the results is also studied.
|
|
|
The proposal of the diagram of a pump series
Šály, Peter ; Veselý, Jindřich (referee) ; Haluza, Miloslav (advisor)
My diploma thesis describes a procedure of creating interactive computer software for company ISH&MSA Čerpadla a.s. in its theoretical part as well as in its practical part. It is a proposal diagram of centrifugal pumps which consists of made and nonmade pumps. After the selection of a certain pump, according to the required parameters of capacity of pump and transit height, the output of the programme is drawing of a flows characteristic, characteristics of coiled paddlewheel and curves of dissipation without any differences in whether the pump is made or not. There is an operating procedure from the initial work with data, short demonstrations from source code, computation of nonmeasured pump to the ascending flows characteristics in practical part of my diploma thesis. In theoretical part, there are explained principles that are needed for comprehension of a pump reform which are used in practical part.
|
|
|
The draft tube design for small water power station Doudlevce
Vintr, Martin ; Veselý, Jindřich (referee) ; Haluza, Miloslav (advisor)
My thesis is engaged in description of ineligibility original version of the elbow draft tube new constructed small hydro power plant Doudlevce. Other main purpose was construction of better hydraulic thus more efficient this draft tube. First chapter meets project small hydro power plant Doudlevce and it specifies this interesting contstruction of the power plant (for example position of the turbine in vacuum fontain) and many others information about it. Second chapter and its particular parts there deal with functions of this draft tube, for example out-flow of water from turbine and a principle of water-energy utilization placing behind turbine runner. There is also described energy profit and how to get it throught draft tube. There is an analysis of important quantities, which are used during the scoring of flow in the draft tube in third chapter. This part of my thesis is aimed to meeting their principles. There is one of the main purposes of this thesis, where is a description of ineligibility original version of the elbow draft tube in fourth chapter. It results sizable from Kaplan´s attemps and analysis of flowing based on computations in computer programme CFD Fluent. Fifth chapter is about general principles, which should be looked out during the construction of the draft tube. There is also project of new hydraulic better draft tube and its another parts. Last chapter compares original version with new better project based on computations in computer programme CFD Fluent. Comparison is made of specific criterion flowing of water, where are described quantites in third chapter, and efficiency of this draft tube.
|
|
|
Spiral case design for fountain turbine Katovice.
Čípa, Jiří ; Veselý, Jindřich (referee) ; Haluza, Miloslav (advisor)
The diploma thesis should identify inconsistencies of the small hydraulic power plant Katovice. The fountain water turbine is now running in slower delivery because the original Francis high speed turbine achieved much smaller flow than a Kaplan type turbine. The aim of the thesis is a project of a spiral case and a distributor for the Kaplan turbine, which should work in higher flow and should be run in its optimum. This project will serve as a base for construction of distributor and spiral case for the small hydraulic power plant Katovice.
|
|
|
Francis turbine runner design
Žák, Radim ; Veselý, Jindřich (referee) ; Haluza, Miloslav (advisor)
The graduation theses are focused on reconstruction of the small hydro-electric power station Harta. Design of detailed runner blading based on the parameters of the given location is part of the reconstruction. Model of the duplex Francis turbine for cast manufacturing is result of the graduation theses. Numerical description of the model was carried out using SolidWorks software.
|
|
|
Drive of control ring PVE Merkersbach
Skoupý, Jiří ; Veselý, Jindřich (referee) ; Kašpárek, Jaroslav (advisor)
This thesis is focused on determination of forces acting to regulation ring of water power plant Markersbach (Germany). Solution of the problem is realized for two variants of servomotors – with and without servomotors acting surfaces balancing. Next topics of this thesis are strenght calculation of piston rod and bottom of the servomotors. Minimalization of the size of servomotors plungers by change of regulation kinematics has been done and minimal pressure in the pressure tank is determined. At the conclusion of this thesis received results are mentioned and its interpretation has been done. This thesis is provided for company Litostroj Power, ČKD Blansko Engineering, a.s.
|
|
|
The Influence of Cultural Differences on Webdesign
Veselý, Jindřich ; Kincl, Tomáš (advisor) ; Novák, Michal (referee)
The work deals with the current burning issue of cultural differences. These issues relate to the expression of culture and one's home country within the mediums of the Internet and online communication. Based on the research of previous studies, this work aims to demonstrate the influence of cultural dimensions in web design and content. In a sample of the largest beer producers in the Czech Republic, Japan and Great Britain supplemented with the largest international brewing companies are analyzed components which characterize cultural differences. The main scope of this study is based on assumptions and theories according to G. Hofstede and E. T. Hall. It thus demonstrates the influence of culture and dimensions -- Collectivism/Individualism, Power Distance, Uncertainty Avoidance, High/Low Context, Masculinity/Femininity, Time Orientation and Colour symbolism. It is recommended that companies pay more attention to the cultural adaption of web communication, which can bring more clarity and attractiveness, and also a higher added value to the customer himself.
|
|
|
Formatting documents with LaTeX
Veselý, Jindřich ; Komárková, Lenka (advisor) ; Bína, Vladislav (referee)
The aim of this work is to acquaint students with the possibility of formatting their graduation theses in other way than usual. LaTeX is in this way certainly more appropriate than a tool such as MS Word. The work is focused on students and accordingly are also designed its parts. Students get acquainted with the most important elements and aspects of language TeX on specific examples or in the form of source code of this work.
|
guest ::
RSS feed.