|
| |
|
|
Dynamic analysis of structure loaded seismic loads
Šulerová, Zdeňka ; Nevařil, Aleš (referee) ; Vlk, Zbyněk (advisor)
This thesis deals with the calculation of response of reinforced concrete construction on the effect of seismic tension. Time and spectral analysis were made. They are mentioned as possible ways of calculation in EN 1998 - 1:2004 norm. Final figures of global deformations and stress on selected beam from the time and spectral analysis were firstly compared for the horizontal components of seismic stress affecting only in one direction. Subsequently comparison of time progress to combination of these effects mentioned in relevant norm was made. In the conclusion the results of used analysis are appraised.
|
|
|
Stress-strain analysis of artery with atheroma
Janík, Rostislav ; Fuis, Vladimír (referee) ; Burša, Jiří (advisor)
This master thesis analyses stress and strain of iliac artery with atheroma. Model of artery is created as 3D and symmetric in the longitudinal cut. The first part of the thesis deals with a research, which includes obtaining information from medicine, which is necessary fort the right solution of the task. Next part dedicates to nonlinear mechanics, constitutive modeling from the view of biomechanice and computational modeling of arteries. In the next part is made analysis for load on artery by increased blood pressure. In the end were specified uncertainties of the used model and evaluated chance of atherosclerotic plaque rupture.
|
|
|
Monolithic reinforced concrete tank
Kollárik, Adrián ; Šiška, Radek (referee) ; Strnad, Jiří (advisor)
The thesis deals with design and assessment of all supporting parts of cast-in-place reinforced concrete tank. The thesis includes a technical report, static analysis, drawing documentations, construction proces and visualization. The drawing documentation consists of shape and reinforcement drawings of supporting parts.
|
|
|
Two-speed gearbox
Kratěna, Jan ; Pokorný, Přemysl (referee) ; Ždímal, Pavel (advisor)
The objective of this work was to create the „Technical Documentation of Two-Speed Transmission“. The submission included a brief content of the demanded work. At first, calculations of gear ratio, tooth system dimensions and module were performed. Subsequently calculations of single tooth wheel loads and their safety were performed. After the tooth system calculation the shaft, bearings and key calculations followed. The Technical Documentation was completed with pictures and charts that illustrate the individual load points. A 3D model of the two-speed transmission inclusive detailed drawings of the individual shafts and tooth wheels were created as a part of the documentation as well.
|
|
|
Strip rolling
Kornherr, Milan ; Suchánek, Miroslav (referee) ; Petruška, Jindřich (advisor)
This bachelor thesis focuses on theoretical analysis of the role of plastic deformation in the process of rolling strips. The work explains progress of stress waveform during straining and lightening. This work also focuses on computing of spring loading and bending moment due to specific curvature of strips. Report at the end of this work includes an illustrative example with executional program.
|
|
|
Frame bridge
Kapsa, Štěpán ; Velešík, Marek (referee) ; Koláček, Jan (advisor)
The work deals with the design of a single-pole frame structure of a road bridge, which is based deeply on piles. Due to the size of the span of 26 m, additionally prestressed cables are designed in the supporting structure. The structure is analyzed by a three-dimensional bar model and assessed for serviceability and load-bearing limit states in the longitudinal and transverse directions. Part of the design is a study of the influence of supporting the computational model and a comparison of the effect of active and resting earth pressure on the structure.
|
|
|
Student Formula Arrangement Design
Niesner, Martin ; Svída, David (referee) ; Ramík, Pavel (advisor)
The rules and specifications of competition Formula Student are the main guidelines at frame design of students' formula. This diploma work discusses frame safety and structural requirements and also requirements on mounting of engine, single axles, rear-axle differential, engine intake and exhaust system, fuel tank, control elements, and so on. In the final parts of this diploma work analysis of maximum state of stress in material of on-load frame is made and total frame torsional rigidity is calculated. Total frame torsional rigidity is compared with those of Formula Ford and with other variants of Formula Student.
|
|
|
Stress, strength and strain analysis of the crane truss construction.
Nedělka, Pavel ; Borák, Libor (referee) ; Vrbka, Jan (advisor)
This bachelor thesis deals with stress, strength and strain analysis of the plane crane truss construction. The aim of this work is the calculation of forces for the simple frame with the help of joint equilibrium equations. These forces will be modified by further construction treatment. This treatment turns the simply frame into the hyperstatic system. The obtained values data are the input data for the design of geometry of particular bars. The unknown dimensions will be determined by two strenght limit states. These limits are: limit state of elasticity and limit state of stability. Then we will make the strain analysis. It will determine the displacement in the action of the force, the effect of actual clearance as well as the brace failury effect to the construction safety. Further will be determined the influence of the weight of the construction to the strenght.
|
|
|
Proposal of a program for solving of problems of simple tension/compression of bars and strut frames
Martínek, Tomáš ; Kubík, Petr (referee) ; Polzer, Stanislav (advisor)
The aim of this work is a program that will solve problems from the simple tension /compression bars and strut frames in the range of bachelor. The work consists of two programs developed in the Borland Delphi development environment. The programs allow the user to define a bar (strut frames) on the basis of the geometrical parameters and constraints, determine the rate of statical indetermination, make the necessary calculations and, if necessary, indicate the condition of deformation (a program for solving bars). The written part of the work serves as a manual.
|
guest ::
