|
| |
|
|
Static solution of wood hall structures
Koch, Filip ; Zídek,, Rostislav (referee) ; Brdečko, Luděk (advisor)
The subject of the thesis is the design and assessment of the roof storage shed. The work addresses four different types of roof structures for hall´s ground plan in size of 12 x 24 m. For each structure is defined geometry, loads, internal forces and drawing up of the opinion of selected elements. The thesis also concerns some important structural details and their solutions. Location of the hall: Brno.
|
|
|
Analysis of possibilities of solution of buckling of a screw-shaped beam
Pokorný, Jan ; Fuis, Vladimír (referee) ; Burša, Jiří (advisor)
Bachelor’s thesis deals with the effect of the pretwist of a column on the increase in buckling load and also focuses on a column with rectangular cross section. This problem is divided into two main parts. The first one is represented by the column with a large thread pitch, the second one by a small thread pitch. The results are obtained by a numerical approach using MATLAB software. The verification is carried out via finite element software. The outcome of this thesis is plotting the ratio of the critical loads of the twisted and prismatic columns against the ratio of the side lengths of the rectangular cross section. The results are shown for both types of considered columns.
|
|
| |
|
|
Computational analysis of cross roll straightening of rods
Štourač, Vít ; Šebek, František (referee) ; Petruška, Jindřich (advisor)
Today is on products from the perspective of quality placed an increasing emphasis. This work is focused to the analyze of cross roll straghtening of long semifinished products with a circular cross-section. This process increased quality of semifinished products from the perspective of their curvature, because they do not reach the required limit values. Curvature of the semifinished product is due to residual stress, which is during straghtening using plastic deformation of the material redistributed and the semifinished product is leveled. This work analyzes the effect of rotation of straightening rolls on the distributiom of contact pressure between the straightening semifinished product and the roll of straightener. Author then analyzes effect of input parameters of program to straightening at the final curvature of the semifinished product. With the experience gained, then try to adjust some input parameters.
|
|
|
Computational analysis of leveling of square cross section rods
Šebek, František ; Návrat, Tomáš (referee) ; Petruška, Jindřich (advisor)
Current requirements in mechanical engineering require more accurate operations and more efficient technologies. The aim of this thesis is the analysis of the leveling of square rods. The main problem is the setting of the leveling machine for the specified material and geometric data so that the initially curved material, which passes through alternatively positioned offset rollers, is leveled as much as possible. The main factor in the leveling process is the plastification of the material used for the redistribution of the residual stress. Based on existing theo-retical knowledge in this field, programs are set up to simulate the passing of the rod through the leveling machine. Further, modifications leading to the improvement of the whole process are presented. Finally, there is a verification of the results which is made independently of the submitted solution and processed by the finite element method.
|
|
|
Three-Aisled Steel Building
Lečbych, Antonín ; Bajer, Miroslav (referee) ; Buchta, Stanislav (advisor)
The thesis contains the design and assessment of three-aisled steel building for small metal production. Supporting span of construction hall is 9, 18 and 9 m. In the middle wing is situated bridge crane with capacity of 2 tons. The estimated location of the object is Luhačovice. The initial design concept was specified by supervisor (as the idea of the investor/architect), for which was did static and structural solution and assembly details. For selected option was made a calculation of supporting structures and selected assembly details. The hall has a rectangular floor plan of 36x36m and ridge height is 9 m. The central wing is made of steel and side extensions are made of glued laminated timber.
|
|
|
Steel structure of a military museum
Šašinka, Jakub ; Barnat, Jan (referee) ; Štrba, Michal (advisor)
The diploma thesis describes the design and assessment of steel structure of the roofing of the military museum in Králíky. The supporting structure of hall is 40.00 meters span. The total layout are 55.93 x 72.04 m, building height 11.43 m, 16.11 m pylon height. Main construction material is steel, grade S355, secondary constructions are made from steel grade S235, rods are made from steel grade S460. I did optimization of steel structure and chose the best option. For this option I made detailed structural analysis. It is prepared by static analysis of the main load-bearing parts of the structure, including joints and details. The supporting structure of hall consists in the transverse direction from the curved spatial lattice structure made of steel circular tubes which hang on rods on a sloped pylon. Part of the report is open-air roofing.
|
|
|
Multi - Purpose Sports Hall
Baudišová, Monika ; Bajer, Miroslav (referee) ; Sýkora, Karel (advisor)
This thesis deals with design of a multi-purpose sports hall. The aim of this work is to design a support structure with a diameter of 80.0 m at ± 0.000. Construction of a circular layout in the level of ± 0.000 of an external diameter 80.0 m. Height of the hall at the top is 20.0 m Indoors girders is solved in 36 beams which meet at the middle of the rings. Ensure the stability of bracing. Anchoring is done by pin connections located at the bottom of the strip, anchored in concrete bases through the base plate and pre-concreted anchor bolts.
|
|
|
The footbridge for pedestrians and cyclists
Pupík, Antonín ; Sýkora, Karel (referee) ; Puchner, Josef (advisor)
This thesis deals with the design and assessment of footbridge for pedestrians and cyclists in the city of Hranice, Rybare district. The footbridge will serve as a crossing point over the river Bečva and will conect cycling trail with the street Rybarska. The content of this paper is to propose two different variants of structures. One of these options is selected based on their economic evaluation and further processed. Length of the bridge is 50m.
|
guest ::
