|
| |
|
|
Rankin cycle for waste heat recovery of internal combustion engines
Kučinský, Josef ; Fiedler, Jan (referee) ; Brázdil, Marian (advisor)
This bachelor thesis deals with Rankine cycle as a method of waste heat recovery for internal combustion engine. Firstly, internal combustion engine and some technologies on waste heat recovery are described simply. Secondly, Rankine cycle and its utilization in automobiles are overviewed. At the end, there are summarized results from simulations and experiments regarding the issue. It was stated in a conclusion that in case of waste heat recovery in automobile, Rankine cycle is a promising technology but it is not ready for wide application yet.
|
|
|
Modern trends in engine forced induction
Podhora, David ; Zubík, Martin (referee) ; Knotek, Jiří (advisor)
The goal of this bachelor thesis is to summarize the fundamental knowledge about supercharging the combustion engines, whereas the emphasis is on the modern trends of this branch. The first two chapters are aiming at the basic principles and reasons for using the supercharging method. Further on, this thesis explains the individual elements of supercharging systems and their possible arrangement. The last part is disserting on the most actual modern trends at supercharging of the combustion engines.
|
|
|
Reduction of Contact Pairs Friction Losses
Novotný, Marek ; Raffai, Peter (referee) ; Maršálek, Ondřej (advisor)
This bachelor thesis deals with the topic of mechanical efficiency of contact pairs in the crankshaft of the combustion engine. The introductory section focuses on the efficiency of the combustion engine as a whole. In addition, it describes the areas where mechanical losses primarily occur. The following chapters describe mechanism of friction losses, the main factors affecting their amount and the most modern ways to increase mechanical efficiency. In the closing chapter, some basic computing relations, describing the size of mechanical losses are listed. The aim of this thesis is to acquaint the reader with the importance of mechanical efficiency in the area of combustion engines.
|
|
|
Design of Modern V8 Combustion Engine
Šebesta, Radek ; Drápal, Lubomír (referee) ; Svída, David (advisor)
Master´s thesis is considered with design and construction of V8 combustion engine with small size and low mass of its body. In the construction were used mass-produced components from the other engines. From every component was generated a 3D model in computer program Pro/Engineer, new necessary parts were made in the same program and put together to assembly. Main part of the construction was to design a new crankshaft, a crankcase and an engine lubricating system. The crankshaft was subjected computing analysis in program Pro/Mechanica, using FEM.
|
|
|
Combustion Engines for Sport Purpose
Smékal, Tomáš ; Ramík, Pavel (referee) ; Dundálek, Radim (advisor)
This article contains description of basic principles of combustion engine, its parts, which suplies motor run and description of possible adjustments for motorsport too. I wrote down some of interesting racing engines and I try to characterize some of most famous world championship. I tried to understand combustion motor runnig, it is the base for building or modifying engines for real racing or modifies productions engines at low level.
|
|
|
Transition State Simulation of Combustion Engine
Forbelský, Antonín ; Beran, Martin (referee) ; Svída, David (advisor)
Master's thesis focuses on the simulation engine transients. The model of single-cylinder engine was constructed in simulation software Lotus Engine Simulation. Then was made simulation of transients. The thesis try to describe the influence of moment of inertia of the engine, the engine starting speed and process of throttle opening during the transients. For all modes also compare two methods of fuel control.
|
|
| |
|
|
The Cylinders of Four-stroke Engines
Vanda, Marek ; Řehák, Kamil (referee) ; Dlugoš, Jozef (advisor)
The topic of this bachelor thesis is Cylinders of Four-stroke Engines. First part is about four-stroke cycle, engine construction. Next parts are about cylinders, their function and requirements. Also included is the importance of the cylinders on the engine operation and engine life. Last part is focused on the construction, materials of the cylinders and their usage in the past and today.
|
|
|
Surface treatments of parts internal combustion engines
Toman, Josef ; Novotný, Pavel (referee) ; Maršálek, Ondřej (advisor)
This bachelor thesis is a professional research dedicated to the most frequently used surface treatments, applied to the stressed parts of internal combustion engines. The thesis also refers to surface treatments classification, benefits for the automotive industry and reasons for their development. Further it focuses on definitions of the technologies used, characteristics of processes and coatings, finishing operations after surface treatments and application of these treatments on the parts of internal combustion engines.
|
guest ::
