|
|
Mikroprocesor control for laboratory power source
Hauer, Petr ; Kubásek, Radek (referee) ; Szabó, Zoltán (advisor)
This bachelor thesis aims to design and implementation a laboratory power supply controlled by microprocessor and PC via USB. The theoretical part describes the USB bus and the manner of its implementation to the microprocessor. There are the basic types of switching and linear sources and methods of control by a microprocessor. The practical part deals with the design and implementation of the resource. The results of this work are the themes of control and power part of power supply, printed circuit boards, software for the PC and microprocessor and measurements on the completed source.
|
|
|
Design of class D audio power amplifier for home use
Raba, Jaroslav ; Kratochvíl, Tomáš (referee) ; Brančík, Lubomír (advisor)
This thesis describes the design and construction of a complete audio power amplifier 2x100W of Class D. The proposal contains an active correction preamplifier unit, a power supply unit and indicator unit of the amplifier excitation. The power amplifier is composed of an integrated circuit TAS5611A from Texas Instruments. The correction preamplifier is controlled by four potentiometers. Excitation of the amplifier is displayed using LEDs. Basic parameters are measured and evaluated for all blocks of the amplifier.
|
|
|
Adjustable source feeded and controlled by USB bus
Staněk, Miroslav ; Frýza, Tomáš (referee) ; Kolouch, Jaromír (advisor)
The aim of this bachelor’s thesis is concept and realization of voltage source which is controlled and feeded by Universal Serial Bus. There will be presented whole design, execution, development progress and finalization of this project in the following text. This source must boost and buck standard voltage from USB. So it will be necessary using two source lines. Microcontroller of AVR family will be used in the direct part of this adjustable source. Into this microcontroller will be embedded USB interface by the software solution. The microcontroller isn‘t used only for communication with PC by the computer programme, but it is also used for switching the source lines by the PWM modulation. According to the minimum output voltage scale (0 – 15 V) this source is useful for a wide spectrum of low- power devices. This equipment could be helpful together with laptop to charging devices (cell phone, camera, pocket osciloscope etc.), which are carried with notebook for doing outdoor activities and measurements.
|
|
|
Controlled light source
Pazderský, Tomáš ; Macků, Robert (referee) ; Škarvada, Pavel (advisor)
The aim of the Master´s thesis is proposing and implementation of computer controlled optical radiation source. The theoretical part describes the photometric, the radiometric quantities, applied components such as LED, the microcontroller and possible methods for the LED brightness control. The development of the device is described from the selection of the individual LEDs to the end of the device assembling and programing. On the several LEDs were made properties measurement. A circuit with microcontroller was designed and then was fabricated. The device was programmed for communication and control from the PC. The entire electronic is fitted in the metal frame of the construction box and finally the device functionality is tested.
|
|
|
Controllable source supplied and controlled via USB
Sedláček, Michal ; Číž, Radim (referee) ; Pavelka, Ondřej (advisor)
Master thesis deals with design controllable switching power source. Device is supplied and controlled via USB bus of PC. The required output parameters are specified by user in a computer application. The teoretical part includes method of USB communication and introduction to switching power sources with focus on a Sepic topologii. The practical part describe individual circuit solution which contains of a complete device. Is analyzed in detail the proposal Sepic converter circuit and controling by microcontroller. The work also includes the design of microcontroller and computer applications. The result of this thesis is a functional device on which is the performed measurement.
|
|
|
Digital audio amplifier with universal inputs
Svadbík, Pavel ; Stifter,, Jiří (referee) ; Kratochvíl, Tomáš (advisor)
This diploma thesis deals with digital audio amplifier with universal inputs and its design. The first part describes modulation and audio formats for audio electronics. The thesis contain design of a block diagram of the digital audio amplifier and describes the requirements for functional blocks. As a basic device for audio signal processing was choosen integrated circuit STA326. The thesis continue with circuits design for each blocks with a description of their principles. The next section describes the construction and firmware for microcontroller. The last part of this diploma thesis is targeted on the presentation of the measured parameters of the amplifier. The conclusion summarizes the results that have been achieved and advantages and disadvantages of the digital audio amplifier prototype.
|
|
|
Design of switching-mode audio power amplifier
Svadbík, Vít ; Sutorý, Tomáš (referee) ; Brančík, Lubomír (advisor)
This work describes the design of audio amplifiers operating in switching mode. The first part describes basic principles of the power stage switching concept. There is described differences between classes of amplifiers according to technology. The second larger part includes design and construction of the switching amplifiers. Design is implemented, including the preamplifier and power supply. Power supply works in switching mode. The measured parameters of the proposed facility are given in the last part.
|
|
|
Adjustable source supplied and controlled via USB
Pavlíček, Petr ; Daněček, Vít (referee) ; Zeman, Václav (advisor)
Master’s thesis deals with design and realization of power supply, which is supplied and controlled via USB bus. In theoretical part there are described principles of USB communication drivers which ensures this communication, there are described principles of linear voltage regulators and basic types of DC/DC converters. Mentioned is also PID regulator theory. Practical part aims for design of suitable DC/DC converter topology and creating algorithms for driving this converter. Next there is created PC program which drives power supply and there are also accomplished basic power supply measurements. The result of this thesis is functional power supply supplemented with PCB.
|
|
|
Design and construction of automatic galvanic line
Vondruš, Jiří ; Janda, Marcel (referee) ; Melichar, Petr (advisor)
This thesis deals with the design of automated system of electroplating. The first part is centered on designing the technological process for this electroplating and the setout of operating vats. It also deals with the project of mechanical construction, electrical system, with the computing procedure and the optimum choice of gear for galvanic line model. The work includes the design of a DC motor controller, the computing procedure and the construction of heating element for vats heater simulation. The last part of this thesis offers an insight to the control system and the assembled program. In the addendum, the photo of the realized model, the wiring scheme, and the programme transcript for control galvanic line model can be found.
|
guest ::
