|
|
Application of Electron Backscatter Diffraction in Materials Engineering
Man, Ondřej ; Vodárek, Vlastimil (referee) ; Svoboda, Milan (referee) ; Švejcar, Jiří (advisor)
The thesis deals with principles and common applications of the electron backscatter diffraction (EBSD) method. Some practical experience in application of the method to a study of highly deformed structure of copper and its thermal stability is described on one hand, and, on the other hand, to a study of phase composition of TRIP steel on various levels of imposed strain. The limitations of EBSD method are discussed along with its resolution in comparison with other complimentary techniques.
|
|
|
Parameter Identification for Elastic-plastic Material Models from Experimental Data
Jeník, Ivan ; Šebek, František (referee) ; Kubík, Petr (advisor)
This master's thesis deals with the identification of the material flow curve from record of tensile test of smooth cylindrical specimen. First, necessary theory background is presented. Basic terms of incremental theory of plasticity, tensile test procedure and processing its outputs are described. Furthermore, possibilities of mathematical expression of the elastic-plastic material constitutive law, thus mathematical expression of the material flow curve itself. Mechanism of ductile damage of material is explained briefly as well. Overview of recent methods of the flow curve identification is given, focused on cases, when the stress distribution in a specimen is not uniaxial. That is either kind of analytic correction of basic formulas derived for uniaxial stress state, or application of mathematical optimization techniques combined with numerical simulation of the tensile test. Also unusual method of neural network is mentioned. For 8 given materials, the flow curve identification was performed using different methods. Namely by analytic correction, optimization, sequential identification and neural network. Algorithms of the last two methods were modified. Based on assessment of obtained results, application field and adjusting the parameters of single algorithms was recommended. It showed up, that an effective way to the accurate and credible results is the combination of different methods during flow curve identification procedure.
|
|
|
Optimalization of Exhaust Manifold for Škoda 1,2 MPI
Kubiš, Milan ; Ramík, Pavel (referee) ; Beran, Martin (advisor)
The subject of this diploma thesis is optimalization of exhaust manifold of ŠKODA 1,2 MPI engine with respect for the plastic deformation at heat stress. The first part is focused on general description of converter module, whose component the exhaust manifold is. In the next part of the thesis is computation of a heat load of the exhaust manifold. The last part is devoted to the seal analysis of the whole converter module of a ŠKODA three-cylinder engine.
|
|
|
Optimalization of Exhaust Manifold for Škoda 1,2 MPI
Kubiš, Milan ; Ramík, Pavel (referee) ; Beran, Martin (advisor)
The subject of this diploma thesis is optimalization of exhaust manifold of ŠKODA 1,2 MPI engine with respect for the plastic deformation at heat stress. The first part is focused on general description of converter module, whose component the exhaust manifold is. In the next part of the thesis is computation of a heat load of the exhaust manifold. The last part is devoted to the seal analysis of the whole converter module of a ŠKODA three-cylinder engine.
|
|
| |
|
|
Optimization of Manufacturing and Assembling Technology of the Valve Bolt
Hrouzková, Andrea ; Zapletal, Josef (referee) ; Doležal, Pavel (advisor)
The thesis aimed to study the impact of manufacturing and assembly technology, the valve bolt fitted to diesel high pressure pump CP3 in the Bosch, which has been found to leak. As experimental material was chosen heat treated bolts M16x1,5 made of material 12 050th. Groups of samples were produced in two ranges hardness. Experimental determination of the optimum range of hardness was assessed on the basis of the results of the process of the screw and set the value of plastic deformation of the sealing surfaces of the parts. Experimental section also deals with the analysis of bearing surfaces on the pump and the components, after the screw process. To some extent, is observed as surface treatment
|
|
|
Removal of residual stress in thin sheets by tension leveling
Dymáček, Martin ; Návrat, Tomáš (referee) ; Petruška, Jindřich (advisor)
Tension leveling is a process used in the steel industry in order to eliminate any shape imperfections of cold-rolled thin strips. The master thesis deals with developing a computer program that generates basic parameters of tension leveling line. The theoretical part of the thesis summarizes the types of the shape imperfections in strips, their causes and the principles of their elimination. This part also presents the mechanism of tension leveling and describes the present-day design of tension levelers. The practical part of the thesis starts with an analytical description of stress-strain behaviour of strip during tension leveling (supposing the simplified conditions). A computer program that allows devising basic parameters of tension leveling line is created on the basis of these analytical relations. The program results are successfully verified by numerical model based on the finite element method (FEM) created in the program ANSYS. Then the interdependencies of certain input and output parameters of created program are determined. These interdependencies can be used as effective design of tension leveling lines.
|
|
|
Metal formíng production of spring bush by cold extrusion.
Třeštík, Jakub ; Samek, Radko (referee) ; Forejt, Milan (advisor)
TŘEŠTÍK Jakub: Metal forming production of spring bush by cold extrusion. The Master’s degrese project, 2nd form, summer semester, academic year 2009/2010, educational group 5O/60, Mechanical Engineering – Manufacturing Technology, Brno University of Technology, Fakulty of Mechanical Engineering, Institute of Manufacturing Technology, Dept. Of Metal Forming and Plastic, May 2010. This project sloves the manufacturing proces sof “Spring bush” part by technology of cold extrusion. Part is made of 12 122.3 steel. Semifinished product has a cylinder shape with dimensions O29-24 mm. This part is made during four bulk forming operations on the TPZK 25 Šmeral Brno, a.s.
|
|
| |
|
| |
guest ::
