|
|
Heating of Golf Club
Míková, Šárka ; Vendlová, Lucie (referee) ; Topič, Jan (advisor)
This bachelor thesis focuses on design of heating and warm water heating of golf club. The theoretical part describes central heating by firewood and pellets. In the calculation part is performed design of the heating system, boiler and necessary devices. And the last part includes technical report and project documentation.
|
|
|
Determination of pressure in the pipe using foil strain gauge
Beran, Vojtěch ; Dokoupil, Pavel (referee) ; Habán, Vladimír (advisor)
This master´s thesis deals with determination of pressure in the pipe using foil strain gauge. It is calculation of the pressure from the measured strain. The main purpose of this work is devise mathematical-technological models to determinate internal pipe pressure from longitudinal deformation. Devised models were used on data from realized experiment and results were compared with real value of pressures in pipes. This thesis contains three models which were mutually compared. Sensitivity analysis were done on two of these models. Thesis also contains opening research of strain gauge problematics. Description of basic knowledge of physical objects mechanic with focusing on shells also belongs to this theoretical part.
|
|
|
Selected designing works on the acid water stripping process
Motyka, Ondřej ; Kilkovský, Bohuslav (referee) ; Jegla, Zdeněk (advisor)
The diploma thesis is focused on selected designing works related to the design of a specific process of acid water stripping. The main purpose of the work is to describe the procedure and the obtained results for these performed design work based on the relevant assignment and the process requirements. In the introductory two chapters, the work focuses on process introduction and description of main process equipment. The following chapters are devoted to the description of the designing works, specifically simulation of the process in CHEMCAD, design calculation of the spiral plate heat exchanger for feed preheating, creation of 3D model and drawing documentation using AutoCAD Plant 3D and lastly strength analysis of the selected pipeline. The main outputs of this work are mainly generated result reports from the process and equipment simulation and strength analysis of the solved pipeline route, 3D model of the process and selected technical and drawing documentation. At the end of the diploma thesis, the performed activities and their outputs are summarized and evaluated.
|
|
|
Project of machine part of hydraulic circuit of laboratory SUA Nitra
Boháč, Daniel ; Ryšavá, Markéta (referee) ; Žoužela, Michal (advisor)
This Master’s thesis deals with design of hydraulic circuit of laboratory of the Slovak university of agriculture in Nitra with focus on project of its machine part. The thesis includes a description of current condition of the laboratory and a list of investor’s requirements. The main task of this thesis is to complete a project documentation which will be used to build a hydraulic circuit in laboratoty of Department of Water Resources and Environmental Engineering under Faculty of Horticulture and Landscape Engineering of the Slovak University of Agriculture in Nitra. The hydraulic circuit is based on recirculation concept. It consists of an underground water storage tank, stainless steel distribution pipes, measuring flumes and centrifugal submersible pumps. The hydraulic circuit will serve employees of the university for their scientific and educational purposes. Important parts of this thesis are hydrotechnical calculations and circuit control visualisations. The final design is based on a series of negotiations with the investor and suits his requirements.
|
|
| |
|
|
Implementation of innovative production of protective liner to the manufacturing company
Kukla, Petr ; Lidmila, Zdeněk (referee) ; Peterková, Eva (advisor)
The Diploma thesis describes the implementation of innovative production of protective liner to the manufacturing company. The liner is manufactured in sizes of nominal diameter DN 200 - DN 500. The material is low-alloy steel EN 10216-2 10CrMo9-10. For the production innovation, the technology of pipe end flaring by a movable mandrel was chosen. Verification of the functionality of this technology was performed using analytical calculations and numerical simulation of FEM. The results of numerical methods were compared with the results of a practical experiment. The experiment was performed on 5 test specimens with a diameter of 273 mm. The machine device was a hydraulic press with a nominal force of 2000 kN and equipped with pressure and position sensors. The experimentally obtained values of force and the tool path dependence were similar with the values of FEM simulation. The difference in the value of the force in the maximum tool path was 290 kN. The flared diameter was formed to a value of 319 mm. This value corresponds to 16.5% of increased nominal diameter, which is sufficient from design point of view. Non-destructive tests ruled out the presence of crack defects on the flared diameter. According the new set up working procedure was produced the first real part. Significant financial savings of CZK 3.5 - 5.3 million / year were quantified in the technical and economic evaluation. Return on necessary investments is between the 9th - 14th manufactured pieces (approx. 15% of the annual production volume). In conclusion, innovation has promising results and will be issued by the company into the production process.
|
|
|
Analysis of Thermoplastic Pipes in a Soil Environment
Ekr, Jan ; Kuklík,, Pavel (referee) ; prof. Ing. Alois Materna, CSc., MBA (referee) ; Gratza, Roman (advisor)
The doctoral thesis deals with an analysis of thermoplastics pipes in a soil environment, in particularly, pipes performed by using trenchless technologies. In the doctoral thesis, experiments of polyethylene pipes loaded by external hydrostatic pressure were performed. The aim of the experiments was to determine a behaviour and load-bearing capacity of the polyethylene pipes loaded by external hydrostatic pressure. For the experiments, a steel pressure chamber was designed and produced which allowed loading and observing a pipe during its loss of the stability. Mechanical properties of the pipe material were determined based on the tensile and bending tests. The series of detailed numerical analyses of the pipe experiments were performed. Various material models which take into account elastic, plastic and viscous behaviour of thermoplastic materials were used. In addition, series of standardized calculations of polyethylene pipes installed using trenchless technologies were performed. The aim was to create new design diagrams for practical assessment of these pipes placed in the partially deteriorated old pipes. In the case of the deteriorated old pipe, a numerical model for determination of design coefficients was created. These design coefficients were verified with standard values. Then, the results of the numerical model were compared with the results of the more complex numerical model which better take into account pipe-soil interaction of various soil types.
|
|
|
High-Quality Visualization of Petri Nets for Publishing Purposes
Bednář, Drahoslav ; Kočí, Radek (referee) ; Janoušek, Vladimír (advisor)
This work is trying to solve the problem of graphical visualization of Petri nets in text publications. The aim of the thesis is to create a tool that will simplify generating of Petri nets and at the same time provide a more aesthetic graphical output than existing tools do. A simplex algorithm was used for automatic network layout. The program has both graphical interface and text mode and can cooperate well with existing tools for working with Petri nets, which the text also mentions. The program is able to load a pnml file and produce a usable image in png, pdf, and svg formats.
|
|
|
Production of exhaust pipe
Frňka, Martin ; Peterková, Eva (referee) ; Císařová, Michaela (advisor)
This work introduces a design of a technology of producing an exhaust pipe. It's semi-finished product is a pipe about a diameter of 76 mm, and the thickness of it's side made of steel 11 320 is 2 mm. Based on a literary study of problematics of bending there was designed bending by minding with a ball thorn and an exterminator. The whole bending set will be fixed to a machine ELECT 150. The procesed production process includes chopping after bending on a circular saw which is followed by insertion of a complete product on a pallet.
|
|
|
Manufacturing of the steam attemperator protective liner
Kukla, Petr ; Lidmila, Zdeněk (referee) ; Peterková, Eva (advisor)
The Bachelor´s thesis deals with the innovation of the manufacturing of the steam attemperator protective liner. The part will be made of low – alloy steel EN 10216-2 10CrMo9-10. The presented work contains an overview of possible production methods, where the technology of pipe end flaring with a fixed mandrel was chosen as the most suitable. The required material parameters were obtained by the tensile test. The application of the selected technology method was verified by analytical calculations and FEM simulation. According to the determined forming force (810 kN), an electro – hydraulic press OMCN 164 with nominal force 1000 kN was chosen. This machine is fully sufficient for the production of this component. The risk of occurring of a defects was excluded based on calculations and simulation. There was assessed considerable financial saving over 53 % in the technical and economic evaluation. In conclusion, this optimization of production is technically acceptable.
|
guest ::
