|
|
VIZIO - dental system automation
Gábriš, Michal ; Šír, Michal (referee) ; Bradáč, Zdeněk (advisor)
This Diploma thesis deals with creation and realisation of extensions for medical dental unit Vizio. Specifically, it deals with electrotechnical solution and software for capacitive keyboard and with proposal of principle of control and regulation of speed for integrated brushless motor. The Diploma thesis contains both the description of used hardware components, and software solution implemented in assembly language. This device is already in commercial use.
|
|
|
Quantification of measurement uncertainty using Monte Carlo
Mareš, Jaroslav ; Šedivá, Soňa (referee) ; Havlíková, Marie (advisor)
This master’s thesis is focused on evaluation of standard uncertanities of measurement by method GUM and Monte Carlo and theirs comparation. In first part of this thesis is made the theoretical analysis of evaluation of measurement uncertanities and proposal of methodology for evaluating uncertainties by Monte Carlo method. In the second part is described direct and indirect measuring of resistance, capacitance and inductance, including evaluation of standard uncertanities of those measurings by GUM and Monte Carlo methods. In the end of this thesis is made comparison of achieved results of spoken methods.
|
|
|
Fractal capacitors properties
Chvíla, Ladislav ; Sedlák, Petr (referee) ; Hruška, Pavel (advisor)
This work is focused on computer simulations of fractal capacitors. The geometry of capacitors and its influence is investigated. Simulations are realized in programs Matlab, SolidWorks and Comsol Multiphysics. There are also several specific examples of different geometrics of capacitors their comparisons and assessment.
|
|
|
Exploring the influence of pressure on the life of lead acid batteries for hybrid electric vehicles
Pospíchal, Martin ; Tošer, Pavel (referee) ; Bača, Petr (advisor)
The lead-acid batteries used in hybrid electronic vehicles HEV operate in high-rate mode in a state of partial charge PSoC. It occurs when the degradation mechanisms related to irreversible sulphation and negative electrodes are a limiting factor in the life of lead-acid batteries. The electrode system was applied to experimental pressure cells of different sizes. Exp. cells were subjected to measurement and evaluation of potential negative electrode, a negative active mass resistance, contact resistance of transition collector - the active mass with the evaluation and measurement of pressure fluctuations within four PSoC runs.
|
|
|
Single-Phase Induction Motor Calculation
Vácha, Pavel ; Vítek, Ondřej (referee) ; Hájek, Vítězslav (advisor)
The master´s thesis deal with the thesis of a single-phase induction motor that is more and more used all over the world. Its aim is assembling the information about this type of motor and its calculation. The content of the first part is the theoretical analysis of a single-phase induction motor and acquirement ways of the stroke moment. Than the work contains a project of basic schema of the single-phase induction motor with an auxiliary phase. The practical part is devoted to an elaboration of demonstration example of the single-phase induction motor with concrete parameters calculation, its method was projected before. Than there is practising successived measuring on the motor of the same parameters made firm EMP s.r.o. Slavkov by Brno in this part. In the conclusion there is the evaluation of the whole process with reached results.
|
|
|
Composite electrode materials for lithium-ion batteries based on LiFePO4 prepared using GAC method
Vilhelm, Ondřej ; Neoral, Jiří (referee) ; Čech, Ondřej (advisor)
Presented work investigates the problem of secondary lithium-ion cells and the different available cathode materials. We have prepared samples of LiFePO4 with the addition of different kinds of carbon materials such as Super P, Vulcan and expanded graphite. We have always created the sample with and without surfactant. Developed samples were compared by measuring electrochemical methods (cyclic voltammetry, charge and discharge cycles and impedance spectroscopy). We also modeled the three-point cell for measuring electrochemical electrode materials.
|
|
|
New electrode structures for alkaline accumulators
Fusek, Petr ; Novák, Vítězslav (referee) ; Vrbický, Jiří (advisor)
Master´s thesis is focused on development of electrodes used in alcaline accumulators, by using new kinds of materials and compounds. Basic possitive eletrode was made of nickel, on this electrode were applied new layers of Ni(OH)2 by using the method called electrodeposition. For electrodeposition was used solution with Ni(NO3)2 in diverse concentrations. Later on, this material was enriched with aluminium admixtures to increase stability of alfa modification in Ni(OH)2. These concentrations were measured and analysed in diagrams. For measurement was used device Biologic. The diagrams were commented with recommendations for production use in accumulators.
|
|
|
Grid dip meter with large-diameter measuring coil
Obr, Michal ; Koton, Jaroslav (referee) ; Hanák, Pavel (advisor)
This master’s thesis deals with grid dip meter, its operating principle, characteristics and with measuring procedure. The thesis contains basic division of oscilators, its characteristics and operating principal. The master`s thesis contains complete design of grid dip meter with large-diameter measuring coil which is placed outside the device. Grip dip meter is made of SMD components on a one-sided printed wiring. Grip dip meter consist of transformer itself, that has two secondary windings as a supply for resonance meters and internal digital frequency meter. The device has analog panel gauge and BNC input for extrenal counter.
|
|
|
Stabilized operation of a 400 kV power line
Girga, Eduard ; Špaček, Jaroslav (referee) ; Blažek, Vladimír (advisor)
Electrical wiring 400 kV is the most used transfer wiring in the Czech Republic with length over three thousand kilometers. It is frequently used for running out significant output from the big power plants and for its significance in electrical engineering. Theoretical part of this thesis deals with the cross-section of mainly used methods for high and extra high stable wiring voltage solution. These methods can be generally dividend into precise and rough. Both of these methods will be analyzed in next chapters. Exact solution comes out from the presumption of equally spaced parameters. The rough solution uses substitution of double gates wiring, this method is accurate enough and accelerates the calculation. Former mentioned reasons explains it’s often use in technical practice. The electric line is substituted by T-cell, II-cell or Steinmetz cell according to length and required precision. Special method of rough solution is the broad method which enables to solve randomly knotted network by using II-cell to replace electric wiring between single knots. This method is mentioned in thesis for completeness; the network solved by me is not knotted. Part of the theoretical thesis is the analysis of specific transfer cases. In computing part will be mentioned not only the computation of stable wiring state with precise an rough method - with all former mentioned cell but the computation of specific transfer cases as well. In the end will be concluded all the counts from computing part and from precision view evaluated used methods of the stable wiring solution.
|
|
|
Methods for measuring the bit rate on the Internet
Pilčík, Jan ; Mišurec, Jiří (referee) ; Zeman, Václav (advisor)
Due to a signifikant development of computer networks in the last few years the demands for measurement of network metrics increased. This master´s thesis is dealing with standards for testing and test techniques used for the measurement of network metrics. Further it compares the existing free accessible measurement tools and metrics measures them. Finaly the thesis draws up a web application for measurement of the basic network metrics.
|
guest ::
