|
|
Rehydration of alkali-activated slag after high temperature loading
Fialová, Barbora ; Bayer, Patrik (referee) ; Rovnaník, Pavel (advisor)
Ground granulated blast furnace slag is a by-product of the steel industry and is often used in combination with ordinary Portland cement as a binder in concrete. When concrete is exposed to high temperatures, physical and chemical transformations lead to significant loss of mechanical properties. This study aims to investigate the effect of high temperatures and rehydration on the mechanical properties, microstructure and phase composition of alkali activated slag. The results of the research could make an important contribution to decisions made concerning the reconstruction of structures affected by fire. In suitable cases it would be possible to regenerate parts of a structure instead of totally rebuilding it.
|
|
|
Fatigue-creep interaction in Ni superalloys and TiAl alloys
Šmíd, Miroslav ; Věchet, Stanislav (referee) ; Kunz, Ludvík (referee) ; Obrtlík, Karel (advisor)
The present doctoral thesis is focused on the effect of dwells on the low cycle fatigue behaviour of advanced high temperature materials. 10 minutes strain holds are introduced into the cyclic straining of cast Ni-based superalloy IN792-5A and cast intermetallic alloy TiAl-7Nb which were chosen as experimental material. Fatigue experiments were conducted in strain control mode with constant total strain amplitude and strain rate. IN792-5A was subjected to continuous cyclic loading test as well as fatigue tests either with tensile peak strain holds or compressive peak strain holds at temperature 800 °C. TiAl-7Nb was experimentally examined by continuous cyclic loading tests and also by fatigue test with tensile peak strain hold times at temperature 750 °C. Cyclic hardening/softening curves, cyclic stress-strain curves, Manson-Coffin curves and Basquin curves were obtained. Stress relaxation data were measured during hold times. Mean stress evolution was observed and documented. Microstructure of both alloys was observed in as-received state and also after cyclic loading by means of SEM and TEM. Surface relief investigation revealed cyclic plastic strain localisation as well as fatigue crack initiation sites. Fatigue crack propagation was described using fracture surface and longitudinal gauge section observations. Dislocation structures developed in the course of fatigue tests were studied and documented.
|
|
|
RESEARCH AND DEVELOPMENT COMPOSITE MATERIAL WITH A HIGHER RESISTANCE TO HIGH TEMPERATURES
Válek, Jaroslav ; Durica,, Tibor (referee) ; Kolář,, Karel (referee) ; Sitek,, Libor (referee) ; Bodnárová, Lenka (advisor)
Concrete has many advantageous properties as regards resistance to fire. It is non-flammable and it has a low thermal conductivity. However, concrete structures, which are not designed for resistance against fire, show significant damage after heating. In particular, the explosive flaking with the consequence of weakening the reinforced concrete cross-section and exposing the steel reinforcement to the temperatures higher than critical temperature of reinforcement. There are only a few possible measures of preventing or mitigating the effects temperature load used. Ways of protection can be divided into two systems: active and passive. Active systems are designed to ensure the greatest possible reduction of temperatures the concrete is exposed to. Passive systems directly resist to high temperatures and fire. Design of composition of concrete with the aim of higher resistance to exposition to high temperatures belongs among the passive systems. A part of the work focuses on summary searches of the problems of concrete and reinforced concrete structures exposed to high temperatures and fire. The goal of the work is defining requirements for cement matrix based composite material and its design ensuring the highest possible resistance to high temperatures or direct fire.
|
|
|
Fracture toughness testing at high temperature range using miniaturized CT specimens
Lokvenc, Martin ; Chlup, Zdeněk (referee) ; Stratil, Luděk (advisor)
This thesis deals with a high temperature testing of fracture toughness and studies the size effect on measured values using miniature size CT specimen. Two types of specimen geometry were manufactured from P91 steel, the standard size and the quarter size specimen. J-R curves were obtained in the temperature range from 23°C to 600°C. No specimen size effect was observed at room temperature tests. The realized experiments together with fractography analysis demonstrated the drop of toughness at 400°C caused by the effect of dynamic strain aging.
|
|
|
Determination of Shortcut Cyclic Stress-strain Curves of Superalloy Inconel 738LC at Elevated Temperatures
Šmíd, Miroslav ; Obrtlík, Karel (referee) ; Petrenec, Martin (advisor)
Multiple step tests under cyclic strain control have been performed using cylindrical specimens of cast polycrystalline Inconel 738LC superalloy at 23, 700, 500, 800 and 900 °C in laboratory atmosphere to obtain cyclic stress-strain curves. During cyclic straining of specimen were obtained cyclic hardening-softening curves. Their progress changed with temperature and strain amplitude. Evaluated cyclic stress-strain curves are shifted to lower stresses with increasing temperature. Surface relief was observed in fatigued specimens under SEM and metalography under optic microscopy. Slip markings were studied on specimen surface fatigued at 700 °C .Stress-strain response is compared and discussed in relation to the surface observations - persistent slip markings.
|
|
|
Diagnostic properties of concrete exposed to high temperatures
Hudský, Petr ; Sitek,, Libor (referee) ; Bodnárová, Lenka (advisor)
This master’s thesis studies the problems of high temperatures on cement concretes, their following diagnostics from pre-treatment to rehabilitation, the emphasis was on the use of high-speed water jet. In the experimental part of the design of a concrete composition with basalt aggregate. Were reviewed the physico-mechanical properties after thermal loading. The influence of pressure water jet on the thermal load on concrete, pull-off test, the volume of the removed concrete with a strength evaluation and comparison.
|
|
|
Properties of alkai-activated aluminosilicates subjected to high temperatures
Halasová, Kristýna ; Bayer, Patrik (referee) ; Rovnaník, Pavel (advisor)
Currently the concept of geopolymer or alkali activated aluminosilicate is very mentioned topic. Many studies concerning utilization of these materials have already been made, but if we want to use these materials in building industry in the future, further research will be needed. This thesis deals with the influence of high temperatures on alkali-activated slag, fly ash and metakaolin-based composites. The work compares mechanical and technological properties, microstructural changes and effect off iller on the geopolymer composites heated at 200–1200 °C. In conclusion, the individual properties are compared and application possibilities of these materials are evaluated.
|
|
|
Possibilities of rehabilitation of concrete structures damaged by high temperaturesv
Vovesný, Václav ; Sitek,, Libor (referee) ; Bodnárová, Lenka (advisor)
The bachelor thesis studies the behavior of the cement concrete exposed to high temperatures. The theoretical part describes the processes in the concrete structure and its individual components. It also describes the diagnostic possibilities of the concrete and its subsequent rehabilitation. In case of rehabilitation and surface pretreatment possibilities, the emphasis was mainly placed on the high-speed water jet. Physical-mechanical properties of the samples were verified by heavy load of pressure from high-speed water jet and high temperature in the experimental part.
|
|
|
Properties of cement composites with fiber reinforcement
Jankech, Filip ; Sitek,, Libor (referee) ; Bodnárová, Lenka (advisor)
This thesis summarizes the knowledge of the possibility of using organic fibres as dispersed reinforcement into cement composites. It is concretely a summary of knowledge about the types and properties of synthetic and cellulosic fibres, their influence on the properties of fresh and hardened cement composite and lastly a description of the fire resistance of cement composites and the effect of organic fibres on the action of those composites at high temperatures and in the presence of fire. The experimental part is supposed to verify the effect of the cellulose fibres on increasing the durability of the cement composite at high temperatures.
|
|
| |
guest ::
