|
|
DC-DC converter for matrix beam module
Sikora, Roman ; Dobesch,, Aleš (referee) ; Hudcová, Lucie (advisor)
The master thesis deals with the development of buck-boost DC-DC converter which supplies matrix beam module. The design is focused on testing two-phase boost converter and three channel buck converter manufactured by NXP Semiconductors. Part of the design is implementation of microcontroller for converter control and communication with computer. Part of the thesis is also to design user interface on Windows platform for easy system configuration. Next thing the thesis deals with is designing load for DC-DC converter that is variable and can make different current consumption. One part of this thesis is focused to achieve the lowest conducted emissions and to maximize conducted immunity. Part of this project is production of a prototype and prototype testing.
|
|
|
Bicycle Additional Drive With A Combustion Engine
And An Electric Powertrain
Doležal, Lukáš
The objective of this paper is power converter design for bicycle with combustion engine and electric power transmission. Converter is powered by a generator which is connected to the combustion engine shaft. The power converter is controlling by microprocessor and control algorithm is designed to achieve maximum efficiently of combustion motor. In this paper is described design of circuits, printed board, driving algorithm and mechanical arrangement of whole powertrain.
|
|
|
Solar Power Inverter
Gottwald, Petr
Design of a solar power inverter with 1 kW output power capability is discussed in this paper. Interleaved boost topology used in the step-up stage as well as the output full-bridge stage are described. Control block utilizing Field-programmable-gate-array (FPGA) is described as well.
|
|
| |
|
| |
|
|
Exercise bicycle for accumulator charging
Nekvapil, Jan ; Procházka, Petr (referee) ; Knobloch, Jan (advisor)
Bachelor thesis is about possible solution construction of exercise bicycle with electric part working as a electric source. The first part of document introduces readers to issues about lead acid accumulators and charging, electronically commutated motors and electric converters. The second part shows potential solving constitution of exercise bicycle and we choose components and devices. EC motor will be connected with exercise bicycle by chain transmission. Transfer energy is realized through diodes rectifier to DC-circuit and then by boost converter to two lead-acid accumulators in series. Document show possible solutions of electric schema and circuit board with suitable electronic components. At the end of the document is compared existing similar products.
|
|
|
Solar power inverter
Gottwald, Petr ; Boušek, Jaroslav (referee) ; Pavlík, Michal (advisor)
Tato práce se zabývá návrhem výkonového měniče určeného pro použití ve fotovoltaických systémech. Klíčovým je použití programovatelného hradlového pole (FPGA) pro realizaci řídicích funkcí. Do detailu jsou diskutovány aspekty návrhu spínaných měničů a na základě takto získaných poznatků je zkonstruován funkční vzorek měniče.
|
|
|
Power Factor Controllers for Switch-Mode Power Supllies
Gálus, Matej ; Steinbauer, Miloslav (referee) ; Murina, Milan (advisor)
The aim of this thesis is to design an active power factor correction (PFC) circuit for correcting a power factor of a switching power supplies. Various possible causes of bad AC mains power factor are discussed. Differences between linear and non-linear loads’ behaviour to AC mains are recognized and discussed. Various passive and active solutions for correcting current displacement and harmonic distortion are reviewed. Boost converter with quasi-resonant switching controlled by Texas Instruments’ UC3855 is chosen for highest total power factor for given power level against other topologies and its high efficiency and lower EMI against traditional boost converter. Various circuit parameters are simulated using PSpice. Complete circuit diagram for an 1kW output power level and worldwide mains voltage compatiblity is designed. After the device prototype was constructed, efficiency measurements were made and measured values are less than expected. This was apparently caused mainly due to absence of saturable reactor and implementation of resistive damping of the quasiresonant circuit’s parasitic resonance. Measured values of power factor are, however, very high and do meet the design expectations.
|
|
|
Uninterruptible power supply with management system utilizing I2C bus for medical devices
Daněček, Vít ; Hanák, Pavel (referee) ; Šilhavý, Pavel (advisor)
Object my master’s thesis is the design a Medical device uninterruptible power supply with managment system utilizing I2C bus. Norm EN 61000-3-2 define electric parameters for medical device power supply. In case of power supply for medial equipment is expressive accent on increased electric strength. This power supply have usually primary and secondary power circuit. Primary power circuit form line accumulator, which supplies needed output to the load and recharge reserve battery. Secondary is formed battery-pack, which serve as back-up power supply at drop-out prime circle. They have a minimum weight, small proportions, large overall effectivity also charging battery-pack and monitoring battery-pack charging condition. Result whole those master’s thesis is design Medical device uninterruptible power supply with managment system utilizing I2C bus and realization board layout. Resulting characteristics designed supply unit are: Output voltages are 5V/ 3 A , 12V/ 1,5 A and -12V/ 0,1 A. Managment support information about: Line adapter/ battery pack switch, battery-pack charging condition and actuall tempera-ture battery-pack.
|
|
| |
guest ::
