|
|
Inverter for arc welding
Matiaško, Maroš ; Huták, Petr (referee) ; Vorel, Pavel (advisor)
This bachelor’s thesis describes designing, paremeter rating and construction of welding source on the principle of high-frequency inverter. The main scope of work is to design a switching inverter for arc welding on the principle of the forward converter. Welding source is regulated for demand of constant current.
|
|
| |
|
|
Switching power supply based on high voltage Si/SiC MOSFET transistors
Darida, Slavomír ; Procházka, Petr (referee) ; Pazdera, Ivo (advisor)
Bachelor’sthesis is based on semestral thesis, which was focused mostly on problematic of switching power supply design with following parameters 3x400V AC/15V DC, 3,333A. Bachelor’s thesis adds algorithmic calculations of converters winding parts for forward converter and also for flyback convertor. These algorithms are created with Matlab. Next extension is design of two different forward convertor’s conceptions. Current mode PWM regulation is the first one and voltage mode PWM regulation is the second conception. Because current transformer is needed for secondary current sensing in first conception, its design is added also with algorithm calculation. Important is that both of these conceptions are using same excitation system. Excitation system functional tests are classified at the end.
|
|
|
Backup power supply with solar panel charging
Křepela, Pavel ; Götthans, Tomáš (referee) ; Kubíček, Michal (advisor)
This project aims to create a backup power source with solar charging for small mobile devices (through USB connector). The charger should store power in a battery that is charged either from external power source or the solar panel. In the introduction, the work deals with the theory of solar cells and batteries. Furthermore, it described the selection of suitable components and design diagram.
|
|
|
Optimization of the switching power supplies with synchronous rectifier
Skácel, Josef ; Macháň, Ladislav (referee) ; Žák, Jaromír (advisor)
This thesis deals with switching circuit topic, especially switching power supplies. There are switching circuits without inductance and their benefits presented in the thesis. Basic topologies of switching power supplies, their properties, application area and functions of basic types of converters are also described. The next section focuses on special resonant switching power supplies and synchronous. The main part of the work is carried out simulations using three synchronous rectifiers. The work includes practical design of an SMPS with synchronous rectifier.
|
|
|
DC/DC step-up converter with synchronous rectifier
Pospíšilík, Vojtěch ; Feiler, Zdeněk (referee) ; Červinka, Dalibor (advisor)
In the bachelor’s thesis we will deal with the design, optimization and subsequent build of the increasing DC converter with synchronous rectifier. Experimentally we find parameters for which we will make the design. Then we choose a suitable control circuit and calculate the parameters of the converter output elements, which assign specific components. After that we will design the printed circuit board, complete and we will renew the converter.
|
|
|
Step down convertor
Koutný, Martin ; Kadlec, Josef (referee) ; Cipín, Radoslav (advisor)
Thesis deals with the evaluation of the solutions and the design of the DC voltage converters. The first describes the different types of converters, which subsequently choose types of resources for the construction. In other chapters of the work devoted to the design of schemes, selected types of sources and selection of circuits and components therefor, for the manufacture, including calculations cooling performance parts. The last chapter is devoted to the description of the structure and measurement of the produced sources. The measurements are primarily deals with the verification of the specified parameters.
|
|
|
Optimization of switching regulated DC-DC converter design
Appel, Daniel ; Ing. Jan Bartoň, Meatest, s.r.o (referee) ; Hejátková, Edita (advisor)
The main goal of this project was an optimization of DC-DC converter design from company Meatest with regards to its efficiency, minimalizing power loses and radiated electromagnetic inference, while maintaining its price on reasonable level. The first part of this paper is introduction to the most common converter topologies. In the second part, design and optimization of converter are discussed. The third part is about measurement automatization in Simple. Measurements of converter prototype can be found in fourth part.
|
|
|
230 V inverter for isolated mains supplied from solar cells
Michálek, Pavel ; Procházka, Petr (referee) ; Martiš, Jan (advisor)
In this thesis is presented detail design of power part of DC/DC converter and output inverter. This device will serve for creating an artificial network in a family house where it will be used for supplying selected household appliances which are designed for use in AC network. The converter will be supplied with DC voltage. This tension will be obtained from a system of photovoltaic panels. The output voltage will have alternate character and it will be close to the network voltage 230 V/50 Hz. In the introductory part of thesis are discussed possible topologies of converters and output inverters. Subsequently are designed individual parts of supply inverter. In the final part there are shown waveforms of important values and is given a thesis evaluation.
|
|
|
Switching driver for high power LEDs with higher efficiency
Doležal, Miroslav ; Háze, Jiří (referee) ; Šteffan, Pavel (advisor)
Problems in swithing converter and power losses in this circuit describe these master’s theses. Power losses have the primar influence on the total effectivity circuit. The first chapter deal swith principle of basic parts switching converter (buck, boost, buck-boost). The power losses on main elements used in switching circuit (diode, transistor) are explained in the next part this thesis. Theory of synchronous rectifiction for reduction of losses. A choice of two integrated circuit useful for future design of LED driver working in buck-boost mode is on the end of the theoretical part. The practical part is fosud on the design of circuits (with integrated circuits chose in the theoretical part) including schematic diagram, calculation of parts and PCB layout. The build samples are evaluated by set of measurements in the field of effeciency, temperatures of components, stability output LED current, EMC and soon. Finally the particular parameters of both tested circuits are compared
|
guest ::
