|
| |
|
|
Solid State Tesla Coil
Pařenica, Jakub ; Mikláš, Ján (referee) ; Martiš, Jan (advisor)
The bachelor's thesis focuses on a theoretical description of the operation of Tesla's transformer, its design, including electronics, and its subsequent construction. The basic theory of the transformer replacement scheme is described. The Tesla transformer is generally described, as well as the methods of excitation of the primary side of the transformer, the generation of the discharge, the skin effect and the meaning of resonance. Furthermore, the work describes the construction of the primary coil holder, secondary coil. The work contains a pattern of the power board from the Eagle program, and everything is accompanied by photos. The work describes the recovery procedure and describes all the waveforms that were measured before and after the connection of the secondary coil.
|
|
| |
|
|
Single-Phase Induction Motor Calculation
Vácha, Pavel ; Vítek, Ondřej (referee) ; Hájek, Vítězslav (advisor)
The master´s thesis deal with the thesis of a single-phase induction motor that is more and more used all over the world. Its aim is assembling the information about this type of motor and its calculation. The content of the first part is the theoretical analysis of a single-phase induction motor and acquirement ways of the stroke moment. Than the work contains a project of basic schema of the single-phase induction motor with an auxiliary phase. The practical part is devoted to an elaboration of demonstration example of the single-phase induction motor with concrete parameters calculation, its method was projected before. Than there is practising successived measuring on the motor of the same parameters made firm EMP s.r.o. Slavkov by Brno in this part. In the conclusion there is the evaluation of the whole process with reached results.
|
|
|
Small Induction Motors
Chvatík, Štěpán ; Mach, Martin (referee) ; Hájek, Vítězslav (advisor)
This bachelor‘s thesis deals with a single-phase induction motor and is organized in five sections. In the introduction is briefly described its construction and compared with three-phase induction motor. The first chapter describes the emergence of a rotating magnetic field of motor, methods of obtaining the starting torque, the influence on properties of different types of motors, comparing the torque characteristics of the different types of motors. In the second chapter is discussed permanent-split capacitor induction motor, its calculation and operational optimization. The third chapter deals with the determination of general principles of calculation and calculation method of single-phase induction motor with auxiliary winding. The fourth part verified the accuracy of these procedures on the selected motor when we performed calculations based on the input parameters of the motor, and after that these calculations are compared with the output parameters which are prescribed by the manufacturer. Verification of the relevance of declared parameters is supported by measurements on the mentioned device and their evaluation.
|
|
|
Design of a prototype table winder for linear coils
Ryza, Vojtěch ; Hrabčík, Miroslav (referee) ; Řehák, Kamil (advisor)
The diploma thesis deals with the design of a prototype table winder for linear coils. The first part of this work describes the basic properties of the coil and its winding methods. In the following section, a critical search was made of the reels available on the market based on which the reel concept itself was created. The work describes in detail the procedure of the winder design together with the design variants of the individual parts of the winders. At the end of the diploma thesis is presented the needed prototype of the coil winder. This problem was solved by using the 3D program SolidWorks and FEM in the program ANSYS Student. The project describes the individual steps of the design of the concept of a prototype linear winder and the component's design.
|
|
| |
|
|
Low power current transformers
Zolich, Ladislav ; Hrabčík,, Miroslav (referee) ; Dostál, Lukáš (advisor)
Master‘s thesis is focused on current instrument transformers, current sensors and low power current transformers. Discussion is made on advantages and disadvantages of each measuring principle. Low power current transformers is then designed and manufactured. Manufactured LPCT is then measured for accuracy class. Results are then compared.
|
|
|
Single-Phase Induction Motor Calculation
Ševčík, Pavel ; Vítek, Ondřej (referee) ; Hájek, Vítězslav (advisor)
This master's thesis considers by single-phase asynchronous motor. The first part discuss about construction, principle of operation and basic parameters of this motor type. It also discussed the emergence of torque and torque characteristics of the different types of engines. The second part explains the basic ways of obtaining grip moment including outline the principles of functions particulars constructions types, which is produce in practice. In the third part is minutely analyse single-phase asynchronous motor with auxiliary phase and permanently conect capacitor, including method of assign size of a capacitor. Fourth part section provides the principles of the procedure for calculating basic parameters of the single asynchronous motor with auxiliary phase. At the last part is accomplished a calculation of single-phase asynchronous motor with permanently conect capacitor at auxiliary phase including comparation with already manufacturing motor.
|
|
|
Analysis of the stator and rotor pack termination effect on the synchronous machine by FEM
Michailidis, Petr ; Valenta, Jiří (referee) ; Skalka, Miroslav (advisor)
This thesis deals with simulation’s possibilities of the electromagnetic fields in electrical machines. A finite element method is the final element technique. The content of this thesis is a model and mesh creation and electromagnetic simulation of synchronous machine. The stator and rotor pack termination effect on the synchronous machine.is analyzed by finite element method in ANSYS program. The type of the stator termination pack is described by four segments. The magnetic field distribution is deformed due to the material properties of used segments. In the next part a methodics of mesh creation is shown. The mesh quality (in term of elements number and elements shape) is important due to the solution accuracy and speed.
|
guest ::
