|
|
Step-up convertor with transformer
Poštolka, Martin ; Procházka, Petr (referee) ; Hejkrlík, Jan (advisor)
This work focuses on the proposal and realization of high-frequency switching source. It consists of a theoretical and a practical part. The theoretical part includes selection and summary of the parameters of converters which we use. It also includes schemes and visual display of the important continuance of magnitudes. We can also find there the enumeration of advantages and disadvantages of every single converter. Further, it is concerned with the selection of the converter which is most suitable for our work. The practical part consists of the calculation and the solution of the step-up converter with the transformer. The realization and appropriate choice of components follows. There is also described the power supply of the switching transistors and how to operate these device.
|
|
|
Laboratory board demonstrates CAN bus
Levek, Vladimír ; Fedra, Zbyněk (referee) ; Frýza, Tomáš (advisor)
The goal of this thesis, is proposal of the laboratory board demonstrates communication by the help of bus CAN. Laboratory boards, controlled with microprocessor, will be send statuses inputs and outputs with each other. Also it will can be transmit and receive messages by the help of the serial port RS-232. With protocol CAN will be send this information: Temperature, Lighting, Analog input 0 - 5 V, Analog output 0 - 5 V, Digital input level TTL and digital output type open collector.
|
|
|
Research in the Field of Anhydrite Binders
Břicháčková, Jana ; Smetanová, Lenka (referee) ; Gazdič, Dominik (advisor)
The presented work deals with research in the field of sulfate binders on the anhydrite base. Conceptually, it is divided into a general theory of sulfate binders and anhydrite mortar compounds, which is describing in detail the using of anhydrite mortar compounds on the poured floor screeds, and then the experimental part, where is made the mineralogical analysis of seven different gypsum resources and subsequent is monitored the effect of two sulfate exciters on the achieved technological properties and hydration process.
|
|
|
Analysis of switched-mode LED drivers
Stehlík, Ota ; Vyskočil, Pavel (referee) ; Kubíček, Michal (advisor)
The aim of this thesis is to design, produce and verify the operation of two different LED drivers for automotive industry, which controls the ultra-bright white LEDs. At the beginning of a brief introduction explaining the principle of operation of LEDs. Furthermore theory describes the functions of all three basic drivers involved as buck, boost and buck-boost. Based on the requirements are selected ICs suitable for this implementation, theoretically described their block diagrams including the individual diagrams and eventually these samples are made, revived and measured their parameters.
|
|
|
Current source for measuring purposes
Chevalier, Stanislav ; Vorel, Pavel (referee) ; Patočka, Miroslav (advisor)
Goal of this semestral thesis is to design power converter which is to be used for measurement. The converter consists of two forward converters in push-pull topology. The converter is to behave as a constant current source with maximum open-circuit voltage of 1000V. Maximum current is 5A. The current range is split into three sub-ranges, to meet the strict requirements on ripple current. The range of currents is 0-5A. The operating frequency of converter is 34KHz. The converter will be charged using two portable electric generators with output voltage 230V.
|
|
|
Car-battery charger
Kadlec, Josef ; Procházka, Petr (referee) ; Červinka, Dalibor (advisor)
This bachelor’s thesis is considered by projection and construction of the car battery charger with switching source. One-pulsed conducting changer is base of this charger. The charger is intended for accumulators of nominate voltage 6 and 12V. Accumulators are charged by method of constant voltage with current limitation of 0.5A, 5A, 20A and 50A. Value 50A has reason during stating of car for example in winter, because the charger helps to battery. The device is equipped with additional protection, which protects the charger and also the accumulator and the supply network. Three pilot lights are the next equipment of the device.
|
|
|
Accumulator tester
Pisca, Marek ; Kadlec, Josef (referee) ; Cipín, Radoslav (advisor)
This master´s thesis is dealing with the theory of Li-ion accumulators and theirs charching. In this thesis has been designed accumulator tester for automatic charging and discharging of Li-ion accumulator. This tester is controlled by microprocessor.
|
|
|
Iverter for three-phase motor
Mikuška, Martin ; Červinka, Dalibor (referee) ; Knobloch, Jan (advisor)
This master’s thesis goes into design of particular circuits for three phase inverter. Inverter’s control is ensured by digital signal controller MC56F8013 with his program. Principle of control is suggested for individual motors. Inverter design considerate universal use and capability for any three phase motor. Particular blocks are compatible each other.
|
|
|
Control Unit for Autonomous Vacuum Cleaner
Matějů, Jan ; Kopečný, Lukáš (referee) ; Žalud, Luděk (advisor)
This paper is in introduction focused on review of robotic vacuum cleaning and evaluation of available products qualities. However the main focus of this paper is system design of all subsystems, control systems and PCD design of robot electronics. In this paper is also described a method for evaluating approximate distance of robot from the obstacle. There are also described problems of system design of IR proximity sensors. The last part of this work is development of control software for robot and its testing.
|
|
|
DC/DC converter
Němec, Martin ; Kuzdas, Jan (referee) ; Procházka, Petr (advisor)
This project deals with transistorized converters in particular a four-quadrant bridge. The main part of project discusses the drivers of transistors and a possible way of controlling a converter. The proposal of control electronics and the regulation structure are involved in the second part. This project also includes a construction of an apparatus which will be used as a teaching material.
|
guest ::
