|
|
A comparison of different types of epoxy adhesives
Mihulka, Jan ; Žák, Ladislav (referee) ; Kubíček, Jaroslav (advisor)
This thesis is focused on a bonding technology. The first part describes the theory of the bonding and it is discussed the main areas of this technology. The experimental part deals with the comparison of four two-component epoxy adhesives in terms of shear strength. For the experiment it had been selected adhesives: Bison Epoxy Universal, Pattex Repair Epoxy Ultra Strong 5 min, Ergo 7430 and Letoxit LH 232. After performing the experiment, it was shown that Bison Epoxy Universal and Pattex Repair Epoxy Ultra Strong 5 min achieved the strengths stated in the datasheet. The strengths of Ergo 7430 and Letoxit LH 232 adhesives was lower than stated in their technological products, thefore, did not meet our expectations. The reason for not achieving the declared strength was probably poor dosing or insufficient mixing of ingredients.
|
|
|
Adhesion of Adhesive Joints for Facade Applications Made of Wood-based Materials
Nečasová, Barbora ; Schmid, Pavel (referee) ; Sedlák,, Petr (referee) ; Kovářová, Barbora (advisor)
The presented dissertation thesis is focused on investigating the adhesive properties of façade cladding made of wood and wood-based materials in combination with flexible adhesion/assembly systems. The systems allow the implementation of effective construction joints and provide a solution with uniform stress distribution which allows the transfer of heavy loads, while simultaneously reducing the weight of the entire structure, which is also often connected with substantial cost reductions. Despite all that, little attention has been paid to this area so far. It is not a solution which is properly embodied in technical standards or in designers´, architects´ and contractors´ awarenesses. The aim of this dissertation is to characterise adhesive properties of selected façade cladding representatives made of wood and wood-based materials for the purposes of bonded joint application in a ventilated façade system. To define adhesion of façade joints, numerical and experimental methods are used, taking also various limit conditions into account. The main conclusion of the dissertation is the characterisation of basic parameters which influence adhesion, effectiveness and quality of façade glued joints. The secondary conclusion is the compilation of a simple methodical procedure for testing and implementing façade glued joints. The dissertation also makes a contribution by extending the current state of knowledge of façade adhesive joints.
|
|
|
The study of adhesion of glued balistic composites on the dependence of materials used.
Dobiáš, Jiří ; Másilko, Jiří (referee) ; Šiler, Pavel (advisor)
The aim of this work was to investigate the properties of bonded ballistic materialsBalistic composites are mainly glued to reduce weight while keeping their protective properties. On this basis, the materials used were ballistic steel, ceramics, rubber kevlar, non-gummed kevlar, Dyneema and fiberglass. For bonding used were a one-component adhesive Collano 36.104 and two-component adhesive Biresin U1305. The strength of the joint was measured in shear at tensile loads. From these results, deformation energy was further calculated.
|
|
|
Vliv vlhkosti na pevnost lepeného spoje při olepení bočních ploch dílců koupelnového nábytku
Landová, Michaela
This thesis is focused on the effect of glue to bonding strength at DTD-L and ABS edge for increased moisture and heat interaction. This problems is concerned not only furniture, which is located in rooms with increased moisture, as are bathrooms and kitchens, but also furniture, which is exposed to these conditions in logistics during transport, storage etc. In this regard selection of right glue has a great impact on produce quality. This work is divided into two parts, theoretical and practical. There is description of methodology and formal view of problematics in the theoretical part. Experimental measurement of temperature and moisture conditions in interior and exterior are introduced in the practical part. Surface material DTD-L was used in practical part, when was tested strength of glued joints with using PUR adhesive. The samples were burden with increased moisture 90 % and 70 % and with temperatures from 25 ° C to 80 ° C. Subsequently was tested strength of gluent joints with using method of angle pressure shear angle-wise 45 ° and a peeling method angle-wise 90 °. The results were processed, analyzed and evaluated.
|
|
|
Vliv teploty na pevnost svařeného a lepeného spoje z materiálu Resysta®
Hrabovský, Štěpán
This master thesis shortly deals with properties and usage of the Resysta material. The main objective of this thesis is to determine a temperature influence on tensile strength of welded and glued joints made from the material Resysta, for an usage such as an outdoor furniture, temperature influence analysis of the joints and to present the results of the analysis obtained by measurements. Further objectives are: tensile strength experiment of material Resysta and to determine influence of placing the pieces in a desk in different directions. Results will serve as a basis for a specific firm; as a basis for deciding between technology of gluing and a technology of welding and also for input for a custom made single purpose machine made for welding of material Resysta. Tests were performed in exposure temperatures -30 °C, 20 °C and 60 °C. We will perform two tests; first test will focus on the tensile strength of glued and welded joints and second one will try to test of tensile strength of Resysta material. Experiments were conducted according to standards ČSN EN 205 and ISO 527-1 on the Instron 3365 testing machine. Laboratory tests showed that values of tensile strength were decreased while increasing the exposure temperature and this was consistent in every test performed. A statistical significance was also confirmed in work piece direction influence on a board. There were higher values of the tensile strength in longitudinal direction than in the transverse.
|
|
|
Lepení spojů zahradního dřevěného nábytku
Knápková, Adéla
Bachelor thesis deals with the influence of humidity on the strength of glued joints of wooden garden furniture by using a mounting adhesive. The joints of solid wood-samples of robinia and spruce were glued with one-component polyurethane adhesive. The bonded joints were exposed to the different humidity at elevated temperature and then it was compared to the strength and resistance between individual woods. Samples were strained on tensile shear strength test.
|
|
|
Design of Hot Melt Glue Gun
Zelenitca, Darina ; Bukvald, Jiří (referee) ; Sládek, Josef (advisor)
The topic of this bachelor thesis is the design of a hot glue gun. Thesis engages in design, technical and marketing analyzes, which indicate the weak sides of the product. The goal is to propose a design, which will respond to costumers’ requirement. To propose a design, which will solve problems and will improve technical, ergonomic and esthetic side of the product.
|
|
|
Bonding of thin metal sheets
Poul, David ; Kubíček, Jaroslav (referee) ; Dvořák, Milan (advisor)
Bachelor thesis is focused on theory and methods of adhesive bonding. Experimental part is focused on two topics: determining dependences of bonded joint shear tension on a cure time and determining dependences of bonded joint shear tension on a size of contact area. Loctite SI 5399 RD acetoxy silicone one component glue was used for these experiments. At determining dependences of bonded joint shear tension on a size of contact area tension is raising, but the grow wasn’t directly proportional on the grow of size of contact area. Determining dependences of bonded join shear tension on a cure time it was proved, that tension is raising first 24 hours very quickly. After this period is process slowing down and tension is increasing to its maximum. After 18 hours bond tension is solid enough to be handling, but 24 hours of curing time is more secured.
|
|
|
Study of durability of wood glue bonds against increased temperature
Kučera, Vít ; Vejpustek,, Zdeněk (referee) ; Vaněrek, Jan (advisor)
In this time are for design of wooden elements available simplified procedures for fire modeling which defines ČSN EN 1991-1-2. But it is not experimentally tested the impact of adhesive on the final value of fire resistance of laminated panels. This diploma thesis solves basic normative practices that could explain the durability of glue bond against increased temperatures. in the practical part will be undertaken to experimentally assess the impact of various kinds of adhesive-based (epoxy, formaldehyde, PUR and EPI) on the glued bond durability against increased temperature. Glued joints that will be subjected to gradual temperature exposure in order to assemble the dependence of the temperature influence on the final strength of the joint according to the type of adhesive.
|
|
|
Factors affecting the properties of glued joints for glues used in the wood industry
Boška, Pavel ; Böhm, Martin (advisor)
Dissertation focuses on the influence of selected factors on the properties of the bond glued by acetate polyvinyl adhesives. Factors such temperature and moisture content of the environment, the pressing pressure and cyclic stress. Despite the same type of adhesive, the properties may vary for different producers of adhesives and according to which the product is not intended. Influence will be compared to the test samples of dried beech timber with regard to shear bond strength. They will be compared properties of adhesives from different manufacturers and different destination. Test samples and test progress carried out in accordance with current standards, or largely based on. This research should help users streamline the process of adhesive bonding and reduce the production costs of the bond.
|
guest ::
