|
|
Permanent deformation on asphalt mixtures
Bambulová, Lucie ; Coufalík, Pavel (referee) ; Hýzl, Petr (advisor)
The bachelor thesis deals with a description of the laboratory properties of aged bituminous binders in relation to permanent deformation. The theoretical part deals with the empirical tests: needle penetration and softening point. There is also explained the procedure and the principle of the MSCR test. In the practical part are evaluated the properties of fifteen tested bituminous binders and based on the results are made two plates which are tested to permanent deformation.
|
|
|
The use DC electrical method in diagnostics of insulating materials
Volf, Michal ; Rozsívalová, Zdenka (referee) ; Frk, Martin (advisor)
In this work describe to the Dielectric relaxation spectroscopy for the evaluation of the actual status of insulation systém. The used methods of quantifying the dielectric response in time domain are polarization-depolarization current and recovery voltage measurement and in frequency domain the loss factor and the complex capacitance measurement. Influence of thermal ageing and temperature dependences of charge and dischage currents are observed.
|
|
|
Design of high voltage source for electrical ageing of insulating mater
Příborský, Václav ; Rozsívalová, Zdenka (referee) ; Frk, Martin (advisor)
Target of this thesis is analyse problems of dielectric materials ageing and environment characteristic applied by ageing process. Types of electric stress are comparing in this work, when and how they are working and how to eleminate them. Next aim is design the high voltage sinus transformer as source for measuring of electric stress and ageing dielectric materials. There is discuss about computer control and collecting of the output datas. In the end is source testing by practical measurement of some dielectric samples.
|
|
|
Influence of the temperature on the preparing of asphalt mixtures with higher amount of RAP
Škrobáček, Petr ; Koudelka, Tomáš (referee) ; Varaus, Michal (advisor)
This bachelor thesis is focused on the preparation of the reclaimed asphalt pavement for production of asphalt mixtures. In the thesis there is investigated the effect of the temperature of preparation the reclaimed asphalt pavement on the characteristic of the bitumen content. In the theoretical part there is described bitumen as such and reclaimed asphalt pavement. In the practical part there is described the preparation of the material for laboratory tests. The next step is the extraction and distillation of bitumen. These bitumens are tested according to depredescribed tests: ‘Determination of needle penetration (ČSN EN 1426)’, ‘The softening point (ČSN EN 1427)’ and ‘Dynamic shear rheometer’. In the last section of this bachelor thesis there is a comparison of the individual properties of the rendered bitumen of the asphalt mixtures of reclaimed asphalt pavement, with the aim of evaluating temperatures of preheating and degradation of the bitumen on the final characteristic of the asphalt mixtures witch higher quantity reclaimed asphalt pavement. The measured values of the temperature for preparation of reclaimed asphalt pavement shows that the temperature of the asphalt mixture before production has a significant effect on the characteristics of the bitumen, which is included in the reclaimed asphalt pavement. There is evident the difference between specimen of the asphalt mixture of reclaimed asphalt pavement and the reclaimed asphalt pavement. It is visible only from the bottom layer too.
|
|
|
Influence of aging on sandwich materials properties
Smékal, Aleš ; Löffelmann, František (referee) ; Klement, Josef (advisor)
The first part of the master’s thesis deals with sandwich materials. Starting with composition of parts which the sandwich panel is made of. The thesis continues with loading distribution and testing of entire sandwich panel. The impact of environment is considered as well. The second part is its goal – determine degradation of the properties of sandwich panels with metal sheets and core after 15 years aging in the common atmosphere and aging in moistheat and salt environment by experiment.
|
|
|
The effect of production parameters on the plasticity of structural steel
Brabec, Martin ; Podaný, Kamil (referee) ; Peterková, Eva (advisor)
The master thesis deals with the influence of heat treatment and storage time on microstructure and mechanical properties of 26MnB5 steel, which is used in the production of tubular components in the quenched and tempered state. The objective was to increase the plasticity of the steel by the definition of new process parameters of the induction heat treatment line. New tempering diagrams of 26MnB5 steel for two various speeds of the heat treatment line were established and used to determine new tempering temperature and speed of the heat treatment line. Observation of the influence of storage time on mechanical properties of the steel did not reveal that it is liable to ageing.
|
|
|
Properties of polymer modified bitumen for warm mix asphalt
Zábranský, Ivo ; Koudelka, Tomáš (referee) ; Dašek, Ondřej (advisor)
The Diploma thesis is focus on polymer modified bitumen for warm mix asphalt. The theoretical part of the thesis describes additives which influence the properties of bitumen for their use and reduction of production and service temperatures. Further, the theoretical part describes the conclusions from the researches. This part also describes empirical and functional tests of bituminous binders. The practical part presents the results of individual tests. Tests were performed on samples of non-aged, aged by RTFOT and RTFOT + PAV methods. The results of the work and the assessment of the suitability of bituminous binders are summarized at the end of the thesis.
|
|
|
Ageing of asphalt binders and mixtures
Štěpanovský, Vlastimil ; Komenda, Radek (referee) ; Hýzl, Petr (advisor)
Diploma thesis is particularly focused on ageing of asphalt mixtures and asphalt binders. In the theoretical part an array of methods simulating short term and long term ageing consequently is introduced. The main objective of the practical part was to carry out the long-term ageing test method BSA (Braunschweiger Alterung). Thereafter, specimens testing for stiffness properties according to CSN EN 12697-26 were made. After conducting the measurement on those, asphalt binder was extracted and processed to follow-up testing. The testing consisted of a range of methods – Penetration CSN EN 1426, Ring and Ball test CSN EN 1427, Determination of the Frass breaking point CSN EN 12593, Determination of complex shear modulus CSN EN 14770 and Dynamic viscosity using a dynamic shear rheometer (DSR). The given results were assessed in the last part in order to evaluate the rate of the binder degradation caused by the method BSA.
|
|
|
Physical-chemical property characterisation of thin reflective layers on silicon substrates
Rozsívalová, Zdeňka ; Studýnka, Jan (referee) ; Krčma, František (advisor)
This thesis deals with surface analysis and characterization of optical features of thin films created by hexamethyldisiloxane (HMDSO) plasma polymerization on silicon wafers. The RF plasma industrial deposition equipment was used for the thin layers formation. These thin films serve as protective coatings on the reflective layer in the car light or solar panels. Theoretic part gives basic information about plasma, its occurrence, features, diagnostics and applications. Thin layers, their production and characterization are discussed here, too. Theoretic description of monomer material (including the group of other organosilicones) is also presented here. The FTIR spectroscopy and elipsometry are mentioned as the main methods for thin films characterisation. Because material during its practical use degrades due to external conditions, the influence of them on the thin layer properties is studied using the accelerated aging of created films. Industrial deposition chamber AluMet 1800V made by Leybold Optics, Ltd. installed in Zlin Precision company was used for the thin films production. Thin films were created under different conditions that were selelected near to the real conditions used in technology. Various applied powers (2-5 kW) were used for the deposition under different monomer flows. Further, the influence of oxygen addition on the created film properties was investigated. The deposition process was monitored by optical emission spectroscopy. The spectrometer Jobin Yvon Triax 320 with CCD detector was used. The selected part from every samples set was exposed by UV radiation (48 hours at radiation density of 0.68 W/m2 at 340 nm) to simulate the probable conditions during the layers real use. The surface properties were investigated by measurement of reflected light spectral intensity in the visible range at different angles. The angle between incident and reflected beam was varied in the interval of 40 - 150° with 10° step. The influence of sample preparation conditions as well as their aging effect was studied at the selected angles. Spectral reflectance doesn´t depend significantly on applied discharge power and oxygen addition. The significant shift of reflectance into the red part of spectrum was observed at UV exposed samples more or less independently on the applied discharge power of monomer flow rate. Addition of oxygen during the deposition suppresses this effec significantly. Characterization of thin layer structure was done by FTIR spectroscopy. No significant changes were observed in the structure at different discharge powers of monomer flow rates except total absorption intensities that are proportional to the layr thickness. The oxygen addition, of course, changes the structure significantly. These results are only preliminary because the layers were very thin (deposition conditions were near to the common process standard) and thus the signal/noise ratio was relatively low.
|
|
|
WETTABILITY OF PCB SURFACE FINISHES
Minář, Jan ; Jana, Toulová (referee) ; Starý, Jiří (advisor)
This bachelor’s thesis with measuring of wetting characteristics by the wetting balance method for samples of different surface finishes from the firm Gatema. It deals with influence of the isothermal aging and reflow processes on wetting characteristics of surface finishes ENIG, HAL and immersion tin. The influence of intermetallic layer on the overall wettability is studied in case of the surface finish of immersion tin. Also deals with the wettability of the nickel layer, after stripped off gold, in case of the surface finish of ENIG.
|
guest ::
