|
|
Influence of working conditions on the signal level detected by LVSTD detector
Tylich, Ondřej ; Zimáková, Jana (referee) ; Čudek, Pavel (advisor)
This bachelor project includes information about function of low vacuum scanning electron microscope and describes it’s parts. It explains the difference between low vacuum and high vacuum scannig electron microscope. Contains informations about creation and detection of secondary electrons using scintillation detectors. It describes the calculation of signal to noise ratio and the method for obtaining the values of signal. Project is focused to determine the value of signal with a change in working conditions obtained by using Low Vacuum Secondary Electron Detector TESCAN (LVSTD). The aim is to determine the stability of the effect of working conditions on LVSTD.
|
|
|
Scintillation SE detector for ESEM
Odehnal, Adam ; Špinka, Jiří (referee) ; Jirák, Josef (advisor)
Thesis deals with theoretical knowledge about scanning electron microscopy and environmental scanning electron microscopy. It describes principle of operation, signals generated by interaction between primary electron beam and specimen and means of detection of secondary electron signal in environmental conditions using scintillation detector. Furthermore, thesis focuses on optimization of detection od secondary electrons by adjusting electrode system of scintillation detector. Computer program Simion is used for modelling signal electron trajectories for proper adjustments. Simulation were starting-point for adjusting the design of the detector. Detection efficiency of adjusted detector was determined by evaluating signal magnitude from captured images, secondary electron detection capability from voltage contrast and quality of the captured images from signal/noise ratio.
|
|
|
Evaluation of Gas Flow at the Proposed Shapes of Scintillation Detector Aperture Sieves
Matloch, Roman ; Špinka, Jiří (referee) ; Maxa, Jiří (advisor)
This work describes briefly electron microscopy issue and physical model of fluid flow. Then the simplified three-dimensional model of scintillation detector will be created in SolidWorks system for 3D cubical models. The gas flow behind the screening in this 3D model will be analyzed and compared by method of finite cube method in SolidWorks Flow Simulation system. This screening will be analyzed in several variants: the screening with 0.6 mm opening and the screening with net-like openings. The results of analyses will be compared according to the requirements. The appropriate shapes from the analyzed parts will be practically measured.
|
|
| |
|
|
The effect of the shape of the intake ports for pumping in a Scintillation detector.
Flídr, Karel ; Vyroubal, Petr (referee) ; Maxa, Jiří (advisor)
The thesis is concerned with the design of the shape of suction canals used for pumping in the scintillation detector. The goal is to perform analysis of the model of the detector according to the current conception and then perform an optimalisation of the suction canals as per demands to their function. In the beginning of the thesis the history of the microscope and electron microscopy is described. The next chapter is focused on a more detailed description of ESEM. The following charter is dedicated to describing the scintillation detector.The thesis recounts the kinds of liquid flow. In conclusion the programs SolidWorks and Ansys Fleunt are described. Next part of this thesis describes in detail parameters‘ settings of simulation calculation. Following chapter introduces designed changes of suction channels shape and its results are shown and described.
|
|
|
Analysis of the gas flow when pumping vacuum for newly designed scintillation detector
Poruban, Milan ; Vaculík, Sebastian (referee) ; Maxa, Jiří (advisor)
The aim of this thesis is to study the issue of eniveromental scanning electron microscopy and pumping gas to create vacuum in the newly designed scintillation detector. Further, creating a model of recently proposed scintillation detector and simulating and analyzing pumping gas in differentially pumped chamber of detector. The theoretical part deals with electron microscopy, electron sources, electron optics and secondary electrons detectors. It is also presented which signals are generated by the electron beam on the surface of a solid. Further fluid flow issues and equations describing the flow in the solved chamber are dismantled. Furthermore, the impact of gaseous environment on the trajectory of primary electrons, because there are collisions of primary beam with atoms and molecules of gas. The following section discusses creating, quality and importance of the network in mathematical modelling. A method of a final volume used to calculate the differential equations describing the flow of gas at the premises of the detector is described . The practical part consists in creating a model of scintillation detector and analyzing the gas flow in drawing a vacuum in the newly designed scintillation detector. At the end the simulation results of gas flow are compared for different variants of apertures and various pressures on the neck of a scintillation detector designed for optimum performance of the detector. The outcome of this thesis is model of newly designed scintillation detector with optimized shapes of apertures according to functional requirements.
|
|
|
Construction scintillation detector with one aperture for environmental scanning electron microscope
Přichystal, Vít ; Vyroubal, Petr (referee) ; Maxa, Jiří (advisor)
The thesis is focused on the design of a scintillation detector with one screen for environmental scanning electron microscope. At the beginning of the work is an introduction to microscopy. Further work is focused on the description of ESEM microscope and a scintillation detector. The following chapter is devoted to the dynamics of flow. They list the types of flow and mathematical description of equations. The next chapter is about using the software and the way of solution of flow. In the following chapter describes a proposal of the diaphragm and extraction method of the detector area. They are described some of type aperture. The last chapter is the conclusion, where the work is summarized.
|
|
|
Evaluation of gas flow in the scintillation detector at different profiles and sizes of holes in the screens that have shaped the network
Truhlář, Michal ; Špinka, Jiří (referee) ; Maxa, Jiří (advisor)
This work deals with the flow of gas in the scintillation detector. Thesis describes the function of an electron microscope, the composition, distribution and development of microscopes from the earliest to modern. The work also includes familiarization with SolidWorks 3D modeling in which is the electron microscope modeled and Cosmos FloWorks in which they are carried out simulations of gas flow. The paper is focused on the flow of gas in various shapes of the screen and various pressures in chamber of specimen. The results of the analysis of both apertures variants are compared with the request to minimize the pressures in the trajectory of the secondary electrons of well as in the chamber of specimen.
|
|
|
Using Computer Aided Engineering for analyse the detector
Novotný, Marek ; Špinka, Jiří (referee) ; Maxa, Jiří (advisor)
This diploma thesis deals with electron microscopy. Examined equipment is environmental scanning electron microscope (ESEM), namely scintillation a detector of the microscope. There is solved the influence of the profile of holes in diaphragms to the resulting pressure and gas flow on the path of secondary electrons at the detector. Introductory part of thesis informs about microscopy in general, with concentration on electron microscopy; especially on scanning microscope, because research is taken just on the environmental scanning electron microscope. Another part informs about both general principles of dynamics of gases and with finite volume method. Another part deals with concrete used software and with setting of individual parameters for calculation. At the beginning of calculation are used five basic profiles of holes in diaphragms for pressure 1000 Pa in the chamber of the sample. For modelling individual shapes is used 3D parametric modeller SolidWorks. Analysis of circulation of secondary electrons through detector is made by using Cosmos FloWorks module. The most suitable type of diaphragms is chosen from measured models. Another part of diploma thesis deals with measuring of chosen types of diaphragms for more pressures in the chamber of the sample; the pressure is 200, 400, 600, 800 and 1000 Pa. The outcomes of this research are both models of pressure and speed of circulation inside the detector and graphically processed values by using different diaphragms, respectively one type of a diaphragm in different pressures. Production drawings of each diaphragm, together with calculated models, are enclosed.
|
|
|
Contrast in image aquired by scintillation SE detector for VP SEM
Koudela, Oldřich ; Špinka, Jiří (referee) ; Jirák, Josef (advisor)
First part of this thesis is a theoretical essay which deals with the basics of scanning electron microscopy, with structure and function of a scanning electron microscope, its’ special case of an various pressure scanning electron microscope, electron interaction with surrounding environment and with a scintillation detector. The applied part of the thesis is focused on evaluation of material contrast on Cu-W specimen. Material contrast is evaluated for different pressures of water vapors in the microscope specimen chamber and for different detection conditions.
|
guest ::
