|
|
Nanoparticels from brake pads wear
Švábenská, Eva ; Roupcová, Pavla ; Friák, Martin ; Schneeweiss, Oldřich
Exposure to particulate air pollution has been associated with a variety of health problems. One of the main\nsources of metal-rich airborne particulate pollution in roadside environments are brake-wear emissions. The \nscanning electron microscopy (SEM) and transmission electron microscopy (TEM), Mössbauer spectroscopy \n(MS), X-ray powder diffraction (XRD) was used to a make quantitative evaluation of wear particles in two \nsamples. Sizes, morphologies, oxidation state, and trace element compositions of wear particles were\ninvestigated using combination of several methods revealed high concentrations of Fe species and phases, \noften associated with carbonaceous material. SEM and TEM observations show that brake wear particles with \na size of tens to hundreds of nm mainly form particle agglomerates. However, ultrafine (<100 nm) particles are \nlikely to pose a health threat after inhalation and/or ingestion.
|
|
|
PROPERTIES OF NANOCRYSTALLINE FE-NI PARTICLES PREPARED BY THERMAL REDUCTION OF OXALATE PRECURSORS
Švábenská, Eva ; Roupcová, Pavla ; Havlíček, Lubomír ; Schneeweiss, Oldřich
Recent technological advancements require development of cost-effective and high-performance magnets \nwhich ideally do not contain rare earth metals or noble metals. The promising candidates are Fe-Ni-based \nalloys, in particular, the Fe50Ni50 L10 phase (tetrataenite), which has a great perspective for producing hard \nmagnetic materials. Our study explores a promising method for preparing nanoparticles of Fe-Ni alloy from an \niron-nickel oxalate precursor. The coprecipitation method was employed to prepare oxalate precursors, \nfollowed by controlled thermal decomposition in a reducing hydrogen atmosphere. The morphology and \nproperties of the resulting particles were analysed using scanning electron microscopy (SEM) coupled with \nenergy dispersive X-ray spectroscopy (EDX), X-ray diffraction (XRD), Mössbauer spectroscopy (MS), and \nmagnetic measurements.\nThe SEM analysis revealed that the particles have approximately cube-shaped unit cell morphology with a\nsize in a range of 1 - 2 μm. Upon annealing, the samples contain multiple phases with varying Fe-Ni content.\nMagnetic measurements confirmed the formation of magnetically suitable Fe-Ni phases in the samples after \nannealing. Mössbauer spectroscopy emerged as a highly effective method for characterizing individual phases \nof the Fe-Ni system.
|
|
|
MICROSTRUCTURE AND COMPOSITION OF FINE PARTICLES RELEASED BY CAR BRAKING
Švábenská, Eva ; Roupcová, Pavla ; Pizúrová, Naděžda ; Schneeweiss, Oldřich
Vehicular traffic is connected with large volume of fine particles released during brake processes of cars. Our research is focused on the phase, structure and chemical analysis of the fine particles taken from some car brake parts by their services. The information on structure and phase composition was obtained by X-Ray Powder Diffraction, Mossbauer Spectroscopy, scanning electron microscopy with EDX and transmission electron microscopy. The results of the wear debris analysis are compared with original brake materials components. Most of recognized particles are based mainly on iron oxides. Wear brake particles are discussed in the relation to the potential risk to the environment and human health.
|
|
|
CHANGES IN ELECTRICAL STEEL SHEETS INDUCED BY HEAT TREATMENT
Bulín, Tomáš ; Švábenská, Eva ; Hapla, Miroslav ; Ondrušek, C. ; Schneeweiss, Oldřich
Surface coating of electrical steel sheets is very important due to minimizing eddy current losses in electrical machines. The quality of coating can differ according to the composition. The coating layer has limited heat stability and after crossing of the guaranteed temperature it can be significantly degraded and its insulation properties may change importantly. The aim of this study is to describe changes in parameters of magnetic behavior of the non-oriented Si electrical steel sheet due to degradation of the coating by annealing in air. The parameters were acquired from the measuring of magnetic hysteresis loops on two types of samples with different excitation. The basic information on structure was obtained by optical microscopy. Acquired data are compared between samples with the damaged coating layer by annealing and the original coating layer. The results are discussed from the point of view of the possibility of using sheets with damaged insulation in electrical machines.
|
|
|
MICROSTRUCTURE AND COMPOSITION OF FINE PARTICLES RELEASED BY CAR BRAKING
Švábenská, Eva ; Roupcová, Pavla ; Pizúrová, Naděžda ; Schneeweiss, Oldřich
Vehicular traffic is connected with large volume of fine particles released during brake processes of cars. Our research is focused on the phase, structure and chemical analysis of the fine particles taken from some car brake parts by their services. The information on structure and phase composition was obtained by X-Ray Powder Diffraction, Mossbauer Spectroscopy, scanning electron microscopy with EDX and transmission electron microscopy. The results of the wear debris analysis are compared with original brake materials components. Most of recognized particles are based mainly on iron oxides. Wear brake particles are discussed in the relation to the potential risk to the environment and human health.
|
|
|
CHANGES IN ELECTRICAL STEEL SHEETS INDUCED BY HEAT TREATMENT
Bulín, Tomáš ; Švábenská, Eva ; Hapla, Miroslav ; Ondrušek, C. ; Schneeweiss, Oldřich
Surface coating of electrical steel sheets is very important due to minimizing eddy current losses in electrical machines. The quality of coating can differ according to the composition. The coating layer has limited heat stability and after crossing of the guaranteed temperature it can be significantly degraded and its insulation properties may change importantly. The aim of this study is to describe changes in parameters of magnetic behavior of the non-oriented Si electrical steel sheet due to degradation of the coating by annealing in air. The parameters were acquired from the measuring of magnetic hysteresis loops on two types of samples with different excitation. The basic information on structure was obtained by optical microscopy. Acquired data are compared between samples with the damaged coating layer by annealing and the original coating layer. The results are discussed from the point of view of the possibility of using sheets with damaged insulation in electrical machines.
|
|
| |
|
|
Nanoscale phases on surface Fe-6Si magnetic sheets
Švábenská, Eva ; Roupcová, Pavla ; Král, Lubomír ; Bulín, Tomáš ; Vondráček, Martin ; Foldyna, Josef ; Čechal, J. ; Schneeweiss, Oldřich
Analysis of the nanoscale phases which appear on the surface Fe-6Si samples were carried out after the various treatments – grinding and etching, annealing, and water jet abrasion. The basic information on structure, chemical and phase composition was obtained by X-Ray Powder Diffraction (XRD), Scanning Electron Microscopy with EDX, Glow Discharge Optical Emission Spectrometry (GDOES), Mössbauer Spectroscopy and X-ray Photoelectron Spectrometry (XPS). The results show high stability of the surface phase composition after the mechanical and heat treatments. Results obtained from the surface analysis in micrometer depth (XRD, EDX, GDOES) do not show any changes after the different treatments. Iron oxides were detected in XPS and conversion electron Mössbauer spectra (CEMS) which analyze the surface composition in a nanometer scale. In addition to, fine changes in atomic ordering on the surface can be observed after mechanical and heat treatments in the CEMS spectra.
|
|
|
Magnetic properties of 42CrMo4 steel
Bulín, T. ; Švábenská, Eva ; Hapla, Miroslav ; Roupcová, Pavla ; Ondrušek, C. ; Schneeweiss, Oldřich
Low alloyed high-grade chrome-molybdenum ferritic steel was investigated from the point of views of magnetic properties in dependence on heat and mechanical treatment. This steel can be used as components of magnetic circuits or some parts in electrical equipment. The basic information on structure and phase composition was obtained by optical and scanning electron microscopy, X-ray Powder Diffraction and Mössbauer Spectroscopy. The temperature stability of the material was proved by measurements of temperature dependences of magnetic moment. The magnetic parameters were obtained by measuring of magnetic hysteresis loops in dependence on saturation field and their frequencies. The results are discussed from the point of view of possible applications as a magnetic material in the very extremely environment, where high mechanical stresses and elevated temperatures can occur.
|
|
|
INFLUENCE OF LASER CUTTING AND PUNCHING ON MAGNETIC PROPERTIES\nOF ELECTRICAL STEEL M470-50A
Bulín, Tomáš ; Švábenská, Eva ; Hapla, Miroslav ; Ondrůšek, Č. ; Schneeweiss, Oldřich
Electrical steel M470-50A belongs to the most often used materials in electrical machines. Due to this fact, it is desirable to know the magnetic parameters after processing raw sheets into the required shape. Basic parameters of mechanical, electrical, and magnetic properties of the sheets are usually obtained from the producer but the magnetic properties are changing in dependence on additional machining processes. The aim of this study is to describe changes in parameters of magnetic behavior after punching, laser and spark cutting of the original sheets. The basic information of structure was obtained by optical and scanning electron microscopy. The magnetic parameters were acquired from the measuring of magnetic hysteresis loops in dependence on saturation fields and frequencies. The results are discussed from the point of view of applied\ncutting technology with the aim to obtain the best magnetic parameters and consequently a higher efficiency of the final product. Results can be used as input parameters in simulation of the electrical machine.
|
host ::
RSS.