|
|
Controlled light source
Pazderský, Tomáš ; Macků, Robert (referee) ; Škarvada, Pavel (advisor)
The aim of the Master´s thesis is proposing and implementation of computer controlled optical radiation source. The theoretical part describes the photometric, the radiometric quantities, applied components such as LED, the microcontroller and possible methods for the LED brightness control. The development of the device is described from the selection of the individual LEDs to the end of the device assembling and programing. On the several LEDs were made properties measurement. A circuit with microcontroller was designed and then was fabricated. The device was programmed for communication and control from the PC. The entire electronic is fitted in the metal frame of the construction box and finally the device functionality is tested.
|
|
|
Digital audio amplifier with universal inputs
Svadbík, Pavel ; Stifter,, Jiří (referee) ; Kratochvíl, Tomáš (advisor)
This diploma thesis deals with digital audio amplifier with universal inputs and its design. The first part describes modulation and audio formats for audio electronics. The thesis contain design of a block diagram of the digital audio amplifier and describes the requirements for functional blocks. As a basic device for audio signal processing was choosen integrated circuit STA326. The thesis continue with circuits design for each blocks with a description of their principles. The next section describes the construction and firmware for microcontroller. The last part of this diploma thesis is targeted on the presentation of the measured parameters of the amplifier. The conclusion summarizes the results that have been achieved and advantages and disadvantages of the digital audio amplifier prototype.
|
|
|
Step-Up converter for mobile device
Gabriel, Petr ; Červinka, Dalibor (referee) ; Huták, Petr (advisor)
The purpose of this bachelor‘s thesis is about to intoduce possibilities of construction and use of switched power supplies. Thesis focuses mainly to description of different types of converters. There are possibilities of power supplie's design and sizing of its components described in this thesis. This thesis contains concrete design of power supply for realization. There are results of the measurement and comparision to the parameters given by manufacturer set forth at the end of this thesis.
|
|
|
Microprocessor controlled inverter for motors
Fiala, Michal ; Červinka, Dalibor (referee) ; Knobloch, Jan (advisor)
This diploma thesis deals with design of universal converter used for motor control by microcontroller. The first part contains concept, functional overview of the device and its parts. The next part deals with mechanical design and construction of the converter and dimensioning of power, control and measurement circuits. The following part describes control algoritm used for three-phase motor and its testing using simulation. The final chapter of the thesis describes PCB mounting and testing of the device and control algoritm on real motor.
|
|
|
Design of switching-mode audio power amplifier
Svadbík, Vít ; Sutorý, Tomáš (referee) ; Brančík, Lubomír (advisor)
This work describes the design of audio amplifiers operating in switching mode. The first part describes basic principles of the power stage switching concept. There is described differences between classes of amplifiers according to technology. The second larger part includes design and construction of the switching amplifiers. Design is implemented, including the preamplifier and power supply. Power supply works in switching mode. The measured parameters of the proposed facility are given in the last part.
|
|
|
Mikroprocesor control for laboratory power source
Hauer, Petr ; Kubásek, Radek (referee) ; Szabó, Zoltán (advisor)
This bachelor thesis aims to design and implementation a laboratory power supply controlled by microprocessor and PC via USB. The theoretical part describes the USB bus and the manner of its implementation to the microprocessor. There are the basic types of switching and linear sources and methods of control by a microprocessor. The practical part deals with the design and implementation of the resource. The results of this work are the themes of control and power part of power supply, printed circuit boards, software for the PC and microprocessor and measurements on the completed source.
|
|
|
Adjustable source feeded and controlled by USB bus
Staněk, Miroslav ; Frýza, Tomáš (referee) ; Kolouch, Jaromír (advisor)
The aim of this bachelor’s thesis is concept and realization of voltage source which is controlled and feeded by Universal Serial Bus. There will be presented whole design, execution, development progress and finalization of this project in the following text. This source must boost and buck standard voltage from USB. So it will be necessary using two source lines. Microcontroller of AVR family will be used in the direct part of this adjustable source. Into this microcontroller will be embedded USB interface by the software solution. The microcontroller isn‘t used only for communication with PC by the computer programme, but it is also used for switching the source lines by the PWM modulation. According to the minimum output voltage scale (0 – 15 V) this source is useful for a wide spectrum of low- power devices. This equipment could be helpful together with laptop to charging devices (cell phone, camera, pocket osciloscope etc.), which are carried with notebook for doing outdoor activities and measurements.
|
|
|
Audio amplifier with PWM modulation for laboratory measurements
Holub, Josef ; Petržela, Jiří (referee) ; Kratochvíl, Tomáš (advisor)
This paper deals with the theoretical analysis of the essential parts of amplifier operating in Class D. It describes the principles and the relationship between the individual blocks. The second part deals with the design of the block connection of a switched amplifier for a laboratory device. The design part contains calculations, justification of the selection of individual components and integrated circuits and schematic connection within the individual blocks. Some blocks are simulated using PSpice and FilterFree. The work also deals with the structural design of the jig and the creation of a 3D model. The annex is contained overall diagram of an amplifier and a complete reference material for production.
|
|
| |
|
|
Adjustable source supplied and controlled via USB
Pavlíček, Petr ; Daněček, Vít (referee) ; Zeman, Václav (advisor)
Master’s thesis deals with design and realization of power supply, which is supplied and controlled via USB bus. In theoretical part there are described principles of USB communication drivers which ensures this communication, there are described principles of linear voltage regulators and basic types of DC/DC converters. Mentioned is also PID regulator theory. Practical part aims for design of suitable DC/DC converter topology and creating algorithms for driving this converter. Next there is created PC program which drives power supply and there are also accomplished basic power supply measurements. The result of this thesis is functional power supply supplemented with PCB.
|
guest ::
