|
|
Control of the 3D printer using Raspberry Pi
Lokajíček, Lukáš ; Kazda, Tomáš (referee) ; Vyroubal, Petr (advisor)
The bachelor project deals with the possibility of solution to control 3D printer type RepRap using single-board computer Raspberry Pi. The theoretical part of semester project contains 3D printing theory focused on 3D printer built at the Department of Electrical and Electronic Technology. The last part of bachelor project is devoted to practical design of compact interface that assure communication between 3D printer and controlling software using Raspberry Pi.
|
|
|
Modification of cathode material based on nickel and manganese for Li-ion cell
Bukáčková, Ivana ; Vondrák, Jiří (referee) ; Kazda, Tomáš (advisor)
This bachelor´s thesis deals with cathode materials for lithium batteries with cell voltage approaching 5V. The first part of the thesis is devoted to the characteristics of Li-ion batteries, electrochemical reactions and properties of electrode materials. She also pays attention to the preparation and measurement of materials LiNi0,5Mn1,5O4, LiNi0,45Mn1,55O4 and LiNi0,55Mn1,45O4. Observed material was measured by electron microscopy, elemental analysis and galvanostatic method,
|
|
|
Modification of Cathode Materials for Lithium-Ion Accumulators
Kazda, Tomáš ; Studničková, Marie (referee) ; Vanýsek, Petr (referee) ; Vondrák, Jiří (advisor)
This doctoral thesis deals with properties of cathode materials for Lithium-Ion accumulators. The theoretical part consists of an overview of the cathode materials and a brief introduction into the very wide area of Lithium-Ion accumulators. The goal of this work was to study the LiCoO2 cathode material and to prepare some modifications of it by doping with other elements. This work was then extended with the study of the new generation of high-voltage cathode materials. The aim of this part was to study their synthesis, their physical and electrochemical properties and the influence of used electrolytes on their electrochemical stability. The work then focuses on the influence of doping these materials and the influence of another part of the battery – the separator – on the overall properties of these types of cathode materials. The results show that doping the LiCoO2 cathode material with sodium and potassium lead to an enhancement of some electrochemical properties as stability during cycling or stability at higher loads and also the long-term stability during aging is better. The LiNi0,5Mn1,5O4 high voltage material was synthetized in both its forms in comparable or even better quality compared with the results from foreign laboratories. The synthesis process was watched in-situ by SEM, thanks to which a unique study of the ongoing changes during synthesis was done. Also the best suitable electrolytes for this material were identified from the viewpoint of stability at high voltages, which is important for the future practical use. Doping of the material with chromium resulted in better stability and capacity both during cycling at standard conditions and at higher temperature and load. A significant impact of the separators on the overall electrochemical properties of the cathode materials was proved, which could be a big benefit for their future usage.
|
|
|
Low temperature Fuel Cells
Kazda, Tomáš ; Novák, Vítězslav (referee) ; Barath, Peter (advisor)
The Bachelor’s thesis is aimed at the low-temperature fuel cells and their usage in cars and mobile applications. In the theory part of this project is described the evolution of the fuel cells in last years and historically as well. Further there are described their functions and particular kinds of the fuel cells with aim at low-temperature cells. In the practical part of this thesis we were making different kinds of carbon mixtures. We have been doing measurements of mixtures on rotate disk electrode and in the experimental fuel cell. At the end of the work are experimentally evaluated different types of carbon materials with different contents of platinum depositing. The results are evaluated using electro analytical methods, using this evaluation to optimize the composition of the material used as electrode material in fuel cells.
|
|
|
Biodegradable bone implants based on iron
Müller, Petr ; Kazda, Tomáš (referee) ; Sedlaříková, Marie (advisor)
The present work deals with the comparison of the properties of metallic biomaterials in terms of their suitability for use as a temporary metal implant. In the work is judged biocompatibility of materials, they are comparing the corrosion rates and the influence of additives in the iron alloy to change biocompatibility and corrosion rate. In a part of this work is suggesting a method of preparing biodegradable metallic samples with different alloying elements and determine the methods, processes and measuring the corrosion rates. Part of this work is the chapter dealing with the function and effect of iron in the human body and any complications that may occur when a surplus caused by the release of part of the implant during its degradation or corrosion products. The outcome of this work is sort of created an iron-based samples in terms of their electrochemical corrosion potential, corrosion rate of samples exposed in various corrosive solutions, spectroscopic elemental analysis and outputs from the microscopic observation of the structures.
|
|
|
Utilization of fotovoltaic effect in combination with electrochromism
Šeda, Radek ; Kazda, Tomáš (referee) ; Jakubis, Ivan (advisor)
This thesis deals with the preparations of titanium and tungsten dioxide active electrochromic layers and simulation of link between electrochromic structures and photovoltaic cell. By means of electrodeposition, the active layers were made on the glass substrates ITO. These layers were subsequently analyzed, namely their intercalation properties. In this thesis, I tried to design the link between the electrochromic element and the photovoltaic cell. After this, functionality of this link was verified by software environment MATLAB Simulink.
|
|
| |
|
|
Positive electrode for lůithium-ion batteries based on LiCoO2
Krištof, Petr ; Kazda, Tomáš (referee) ; Sedlaříková, Marie (advisor)
This diploma thesis deals with materials used by production ofcathodes of Lithium-ion batteries. Primary this thesis deals with LiCoO2material and its subsidizing of alkali metals. The first part deals with the charakteristic of Lithium-ion batteries, used materials, possibilities of doping and charging. The practical part concentrates on production of active substance of cathode and doping this substance by sodium and potassium. The methods of evaluation were used galvanostaticcycling and x-ray analysis (XRD).
|
|
|
Optimalisation of coposite materials for civil engineering
Kazda, Tomáš ; Chladil, Ladislav (referee) ; Novák, Vítězslav (advisor)
This work is focused on optimalisation of coposite materials for civil engineering. In the theoretical part of the project is introduction of the composite materials and materials which are used for their production. There are also concerned their properties and possible application areas. In conclusion of theoretical part this project is a summary of the possible use of composite materials. The practical part compares the characteristics of the different types of composites made in terms of conductivity and the rate of corrosion.
|
|
| |
guest ::
RSS feed.