|
|
Reinforced concrete aeration tank
Vlach, Jakub ; Strnad, Jiří (referee) ; Šulák, Pavel (advisor)
The aim of this work is to design and static analysis features open embedded aeration tank wastewater treatment plants, in particular the assessment base plate and exterior walls. On the basis of reports is prepared drawings consisting of reinforcement drawings and drawing shapes. The proposal was made on the values of the internal forces of the outputs of computer program SCIA Engineer 2012-Student Edition.
|
|
|
The assessment of existing structure
Pospíšilová, Lenka ; Pinkas, Karel (referee) ; Klusáček, Ladislav (advisor)
This document aims to assess existing reinforced concrete construction od single-storey hall. There is gradually made static calculation and made judgment on individual supporting elements of reinforced concrete construction. There was very important aspect of assesment load. That aspect was to calculate with planned instalation of a new overhead crane with greater capacity. The main basis for the assessment of existing construction was building-technical survey, the results of which were determined input parameters calculation. The aim of the study was to assess whether it is possible at the current technical state of the construction fitted in the future of higher overhead crane capacity required, or propose such technical measures that would allow this.
|
|
|
Slab bridge in Velké Pavlovice
Gřunděl, Michal ; Hofírek, Radovan (referee) ; Koláček, Jan (advisor)
Bachelor thesis deals with the design of the new bridge according to EN 1992-1-1. The bridge is used to convert local road across the river Trmánka. The bridge is designed as a plate with a full cross-section of the trapezium, a statically resolved as a bridge is just stored with the length of bridge 12, 1 m. Categories of communication is S 7.5. Encumbered and assessment on the MSÚ and MSP is resolved according to the standards.
|
|
| |
|
|
Analysis of reinforced concrete bridge
Řeháček, Jakub ; Panáček, Josef (referee) ; Zich, Miloš (advisor)
Bachelor´s thesis is concerned with state estimation of reinforced bridge. The bridge is used to transfer local road across the Svratka river. The bridge is designed as arched bridge with tie and down deck. Lenght of bridging is 24,8 m. Loads and state estimation are done according to Eurocode.
|
|
|
Prestressed bridge in Velké Pavlovice
Stloukal, Radim ; Růžička, Stanislav (referee) ; Koláček, Jan (advisor)
The subject of this thesis is to design a bridge construction over the river Trkmanka in the municipality Velké Pavlovice. The superstructure is designed as a prestressed one field slab bridge with the length of 16,85m. As a part of this thesis there is enclosed structural analysis calculated accordingly to ČSN EN 1992-1-1. The load effects were calculated by Scia Engineer and compared with manual calculation. The rest of the calculations are done manually and ocassionally compared to engineering software. The construction has been analysed for the ultimate limit state, serviceability limit state and the stress anchors have been designed.
|
|
|
Static analysis of reinforced concrete floor structure of historical building
Nani, Pavel ; Bažant, Zdeněk (referee) ; Zich, Miloš (advisor)
The chief objective of my bachelor’s thesis is a design of the reinforced concrete floor structure of a historical building over 1st floor. The historical building was built in 1874. There are three floors in this building and there isn’t any underground floor. The reinforced concrete floor structure consists of the following forms of structure – a ribbed ceiling, a floor slab, a beam, a shell of vault and a staircase. The ribbed ceiling is made from a lost formwork of the VELOX firm. The set reinforced concrete floor structures are according to ČSN EN 1992-1-1.
|
|
|
Design of a one-span beam bridge
Fojtů, Jan ; Panáček, Josef (referee) ; Nečas, Radim (advisor)
The aim of the thesis is a safe and economical design of a bridge over a watercourse according to all valid regulations and standards. There were designed three possible options in accordance with the recommended dimensions. The variation with the cross-section that consists of two beams and effective width of flanges is preferred. The thesis is mainly focused on the design of bearing concrete structure.
|
|
|
Brick Building Reconstruction
Kolářová, Jana ; Bažant,, Zdeněk (referee) ; Šulák, Pavel (advisor)
This bachelor’s thesis is focused on reconstruction of brick apartment houses in terms of static load capacity. The thesis summarizes the requirements and information to evaluate the current state of brick buildings, contains both theoretical and practical calculations to assess the load capacity of masonry elements, and suggests possible measures for structures in unsatisfactory conditions.
|
|
|
Resistance of the roof structure loaded with photovoltaic panels
Holoubek, Jan ; Bažant,, Zdeněk (referee) ; Strnad, Jiří (advisor)
The aim of the thesis is to verify the resistance of the roof structure loaded with photovoltaic panels. On the roof of industrial building of rectangular plan with dimensions of 26,5 x 24,5 m in Hlinsko, the investor decided to install photovoltaic panels. Preliminary diagnostic survey showed only flexural reinforcement in the field of all considered load-bearing elements. Bending strength was assessed by these structural elements: reinforced concrete slab, reinforced concrete beam, reinforced concrete grinder. Static calculation includes a minimum reinforcement of support and necessary shear reinforcement, which must be demonstrated by a detailed diagnostic survey. The structural analysis includes the assessment of reinforced concrete beam deflection after loading. All assessments were performed according to currently valid Eurocodes. The calculation showed that all supporting elements meet the bending resistance and deflection of the beam is smaller than the limit value laid down in the EC, so the roof of the hall can be loaded with photovoltaic panels.
|
guest ::
