|
| |
|
| |
|
|
Laboratory Measurements of Skin Conductance
Slouka, Petr ; Harabiš, Vratislav (referee) ; Sekora, Jiří (advisor)
This thesis contains an introduction to anatomy and physiology of the skin highlighting its barrier function. The barrier function of the skin enables it to separate internal organism from external environment. thermore, the electrical properties of the skin are described and possibilities of skin conductance measurement are discussed. The thesis presents a design of a device for the skin conductance measurement as the method of evaluation for barrier function. Alternating current is used for measurement during iontophoresis for evaluation of skin conductance. Circuit design and circuit board are included with a list of parts. The designed device was realized and in the end it was tested and the results were discussed.
|
|
|
Current source for measuring purposes
Chevalier, Stanislav ; Vorel, Pavel (referee) ; Patočka, Miroslav (advisor)
Goal of this semestral thesis is to design power converter which is to be used for measurement. The converter consists of two forward converters in push-pull topology. The converter is to behave as a constant current source with maximum open-circuit voltage of 1000V. Maximum current is 5A. The current range is split into three sub-ranges, to meet the strict requirements on ripple current. The range of currents is 0-5A. The operating frequency of converter is 34KHz. The converter will be charged using two portable electric generators with output voltage 230V.
|
|
|
Electronic circuits with active elements at current mode
Bačkovský, Pavel ; Sedláček, Jiří (referee) ; Murina, Milan (advisor)
This bachelor’s thesis deals problems with current feedback amplifiers and their comparison with voltage feedback amplifiers. Then it adverts to mutual differences and compares their parameters. This thesis shows basic circuits with current sources and with power boost of this circuits. This thesis designs conception of current source. Simulation, complete details for realization of current source, drawing printed circuit and specification card used parts are part of this work. In the end this work the parameters of current source are checked.
|
|
|
Controlled light source
Pazderský, Tomáš ; Macků, Robert (referee) ; Škarvada, Pavel (advisor)
The aim of the Master´s thesis is proposing and implementation of computer controlled optical radiation source. The theoretical part describes the photometric, the radiometric quantities, applied components such as LED, the microcontroller and possible methods for the LED brightness control. The development of the device is described from the selection of the individual LEDs to the end of the device assembling and programing. On the several LEDs were made properties measurement. A circuit with microcontroller was designed and then was fabricated. The device was programmed for communication and control from the PC. The entire electronic is fitted in the metal frame of the construction box and finally the device functionality is tested.
|
|
|
Driver of Semiconductor laser for 1Gbit/s
Melichárek, Radek ; Vařacha, František (referee) ; Prokeš, Aleš (advisor)
This thesis describes a design of a driver for a specific type of laser VCSEL. Models for simulation in PSpice OrCAD have been developed for this type of laser. The qualities of the designed driver aim to be equal to the integrated drivers that are available and to remove some of their drawbacks. It consists of the following components: input LVPECL receiver/driver, differential amplifier, fixed source of a modulation current, circuit of automatic power control. Regulation of the modulation current is dealt with atypically using an aptly selected input LVPECL receiver/driver which enables to control the voltage amplitude on its output by means of voltage. The thesis also describes different types of coupling between laser and driver. The most appropriate alternative is selected taking into consideration the unconventional design of the driver. The connection of the driver is supplemented by a microcontroller which secures control of output optical power by means of a serial bus RS232.
|
|
| |
|
|
Controlled power generator of current impulses
Gabriel, Viktor ; Vrba, Kamil (referee) ; Rampl, Ivan (advisor)
The goal of this thesis is to design and realise microprocessor-controlled generator of current impulses, which are being brought in induction load. Thesis contains description of individual functional generator parts, mainly microprocessor program equipment. The text also aims for inductor design as an induction load and other solutions of power parts with the selection of the most suitable one. The generator of current impulses itself is realised on two-sided printed circuit board.
|
|
|
Utilization of light emitting diode lighting
Podola, David ; Černý, Michal (referee) ; Paloušek, David (advisor)
This bachelor thesis deals with problems of illumination by LED diodes. Basic concepts of lighting technology are defined in the first part. The second part is dealing with the construction of body LED diodes and explains the principle of white light formation to LED. Introduces problems of cooling. Gives an overview of the available power sources for LEDs. Provides an overview of how to control lighting by using motion sensors and presence sensors. Will be made basic economic balance sheet, which will evaluate the advantages of using LED sources. Attachments provide the LED catalogs of manufacturers, accessories for LED and comment on other sources of information.
|
guest ::
