|
| |
|
| |
|
|
RF analog fiber optic link
Kelbler, Petr ; Jedlička, Petr (referee) ; Drexler, Petr (advisor)
This thesis analyzes the problem of design analog fiber optic link for transmission high frequency signals. Analog fiber optic link will be used in system for detection and localization a partial discharge activity MOSAD-PD-UHF, where will replace existing solution with coaxial cables, which is not appropriate for highly noise environment. MOSAD-PD-UHF system is developed in department of theoretical and experimental electrical engineering. At the first, MOSAD-PD-UHF system and individual parts of optical chain are theoretical described. In following part are compared a few commercially available analog fiber optic link and design of chosen transmit and receive module are described. . The thesis final part deals with construction of optical link and measured parameters are discussed.
|
|
|
Effects of mechanical doings on optical data transport
Tihlařík, Tomáš ; Křepelka, Václav (referee) ; Filka, Miloslav (advisor)
This master´s thesis deals with of human factor impact on optical fibers manipulation. It describes types and methods used for splicing and placing optical fibers and optical cables. These methods are specified in the chapters; their application in different environments and conditions is accentuated. This paper presents splicing optical fibers. It emphasizes problems which can occur if proper procedures aren´t kept or if improper device is used. In the thesis there is the chapter dealing with problems which can arise during splicing optical fibers - these negative influences are evaluated with educational equipments EF-970-01 PLASTIC by the company MIKROKOM, s.r.o. Another aim of the work is to describe mechanical optical fiber splice 3MTM FibrlokTM. This kind of device was lent for testing optical fibers multiple splicing. It was tested under extreme conditions. Statistically processed values of insertion loss and splice reflectance, measured by OTDR are the results of the test. Comparing measured values, technical report ones, regarding for usage in practice, there is a possibility of 75 multiple reusing of the mechanical optical fiber splice. The prediction of magnitude insertion loss, calculated for thousands splice cycles follows. The next part of the work deals with fusion splices and contains comparison of splices made with two cleavers: CORNING LWL-TRENNGERAT S46999-M9-D12 and the later model - Fitel S325A cleaver. The result is that older S46999-M9-D12 model gained lower attenuation. The results of both previous measurements are influenced by human factor. It appears at mechanical optical fiber splices as growing fluctuate of insertion losses and as the unequal attenuation fusion splices at tested cleavers.
|
|
|
Parameters of FTTx networks - Quality of services
Winkler, Aleš ; Reichert, Pavel (referee) ; Münster, Petr (advisor)
The main subject of this diploma thesis is to make a proposal to improve the optical access network for the transmission of Triple play services. I would here to the reader clarify method of proposal of optical network. There are described the kinds of optical access networks with parameters, for which we must look by their construction. There are described the modern methods of construction optical network too. In the theoretical part are discussed used architecture of networks too. I met here known standards, which I compared for big importance by their choice. A reason of construction of optical network are services known like Triple play. These services together with their problems and parameters are here discussed too. At the end of theoretical part I listed here measuring method for getting negative attribute distorting the led signal. In practical part the locality witch use the optical signal as the source of information is ordered. These network use unfit connections and has less possibilities than usual and this is the reason, why is the network not able to supply Triple play in requested quality. At first the analysis of ordered network was needed. Situation was complicated by the fact, that it has been prohibited entrance to me. The structure of network and network parts was known and documented by me. I made the proposals to improve this network in practical part. By the first proposal remained original kind of access network FTTB, but used new parts with higher performance. By the second proposal I made the network FTTH, by which it was possible to use the last haul optical cables with treatment and using new elements. It was needed to create solution by flat units. The resulting proposals are here evaluated, compared and cost evaluated. For rejection of access to optical network I did not make measuring, so I made simulation for variant FTTH for getting some parameters negative acting transmission.
|
|
|
Design of optical fiber sensor for vibration detection
Janoušek, Adam ; Münster, Petr (referee) ; Dejdar, Petr (advisor)
The master theses deals with a detailed analysis of optical fiber sensors. Specifically, there are discussed optical fibers, various types of sensors and realization optical fiber senzor and senzor system that has been optimized and processed data in real time. In master theses also describes the LabView programming enviroment and uses components, including the entire sensor systém of a sensors system that sends measured data
|
|
|
PMD - polarization mode dispersion and its effects on data transport
Trávníček, Pavel ; Dostál, Otto (referee) ; Filka, Miloslav (advisor)
My graduation thesis is concerned with the effect of polarization mode dispersion on transmitted signal by optical line. It describes external and internal causes of origination of polarization mode dispersion. On the basis of these effects there is a differential group delay (DGD). It is the time delay in meantime within individual modes. DGD results in a time extension of impulsion and limitation of maximum bit rate. This thesis contains localization methods of part of gossamer filament with increased value of PMD by POTDR method. This method is based on the principium of back dispersion and its modifications SOP a DOP. Very important chapter of this thesis is the measurement of the polarization mode dispersion. There are described methods of PMD measurement. It is the interferometric and polarimetric method and the method of state of polarization. The major part of this thesis is about the reduction of polarization mode dispersion effect. This part is divided into two parts. First part is about the methods of PMD effect reduction and the second one is about the PMD compensation. The discrepancy between these two parts is the reduction way of PMD effect on transmitted channel. The compensation use the compensation components inserted into the transmission path. By PMD reduction methods we can solve the problems from the view of changing of fibre or all cable. For better understanding of polarization mode dispersion effect there are simulated 4 optical lanes of various parameters. The simulation output is the eye diagram which provides the view at results of transmission lane. In the final part there is the evaluation of measured parameters of optical lanes simulated in a laboratory.
|
|
|
Optical Network Design in Revúca
Antalík, Dominik ; Jordán, Vilém (referee) ; Ondrák, Viktor (advisor)
Bachelor thesis is focused on the optical network design with a variant termination of the optical fiber in the home of end users. The technology is currently the most advanced bandwidth sufficient for reliable transmission of any kind of content. The investor is the local internet provider FERDINANDY, s.r.o. in Revúca. The optical network design is set for this city. This innovation will provide high speed connection and offers additional service options such as IPTV or VoIP for citizens of Revúca. The bachelor thesis includes a proposal route of the optical fibers, choice of active and passive equipment and economic assessment of the payback period of large investments.
|
|
|
Power-Over-Fiber power supply
Kos, David ; Vlček, Čestmír (referee) ; Drexler, Petr (advisor)
This thesis deals with the possibilities of energy transmission by optical fiber for the purpose of powering of electronic systems. It comprises issues of electrical energy conversion to optical energy, coupling the power into the optical fiber, coupling between fiber and opto-electric transducer, conversion of optical energy to electrical energy, and transformation on required voltage levels. The principles of such Power-Over-Fiber are discussed in the first part of the work. Various technologies for the implementation of key system parts and their effectivity are discussed. In the next part, several Power-Over-Fiber commercial devices are compared. Subsequently, systems for Power-Over-Fiber experimental implementations are proposed. They are based on the utilization of semiconductor laser, multimode fiber, photovoltaic cell and related electronic circuits. The final part of the thesis deals with the construction of experimental systems and measurement of parameters of transmitted power and efficiency.
|
|
|
Mathematical analysis and simulation of optical fiber transmission parameters
Smrž, Jan ; Šporik, Jan (referee) ; Tejkal, Vladimír (advisor)
This thesis deals with the transmission of optical fibers, their properties and method of calculation. The paper presents different types of fiber types and standards. There is a description of the connection of optical fibers with different methods, including variations joints. Further side effects are broken fibers, dispersion and attenuation. The last part is devoted to describing the program, which was part of this work. The program is used to calculate the transmission parameters of optical fibers and optical losses incurred in connection.
|
guest ::
