|
|
The Steel Structure of Car Showroom
Buchta, Vojtěch ; Buchta, Stanislav (referee) ; Hron, Lukáš (advisor)
The task of the thesis was to design a draft and a review of car’s showroom supporting structure. The object is located in the city of Hradec Králové. Floor plan has a size of 30 x 15 m, the height of the object is 7 m at the highest point. The mono-pitched roof is formed by two parts on the same slope 3.81 °. Material of all components is steel S235. All calculations were performed in accordance with valid standards. The structure consists of a load-bearing columns fixed to the ground, the truss girders are designed of hollow cross-sections, pin-suported by the columns. The purlins are pin supported by upper chords of a truss girder, with the lower and upper edges flushing. Purlins support the roof made of roof-panels by Kingspan, thickness 160 mm. Wall casing the technical parts of the object is formed also by system panels by Kingspan. The cladding of the sales area is made of glass panels by Reynaers.
|
|
|
Design of the test facility
Pavluš, Martin ; Pavlík, Jan (referee) ; Tůma, Zdeněk (advisor)
The thesis deals with the design of automated testing equipment of selected types of pneumatic valves. The problem of manual control process is its inefficiency, both in terms of human error rate and time loss caused by further assembly. The automated manual inspection process eliminates the problem. In the theoretical part, the types of switchgear are described, selected measuring procedures and methods of measurement are described. In the practical part, the measuring procedure was set out and on the basis of it there were designed variants of the testing machine and test circuit. The conclusion of the thesis contains evaluation of the whole project.
|
|
|
Mechanical barrier project
Kubeš, Ondřej ; Škopán, Miroslav (referee) ; Malášek, Jiří (advisor)
The first part of the thesis analysis is about the most common concepts of barriers which restrict the passage of vehicles. These provide security for parking cars. On the basis of this analysis is made design of road barrier. This proposal is accompanied by the plan.
|
|
|
Magnetic separator
Šnédar, Jan ; Malášek, Jiří (referee) ; Jonák, Martin (advisor)
The aim of this bachelor thesis is to design the structural conception of belt magnetic separator with permanent magnet designated to separate unwanted ferromagnetic material waste from the machining of aluminium. This report contains an overview of equipment for the separation and design of concrete solutions to the magnetic separator. According to the input parameters are calculated all the parameters necessary for correct machine design. Attachments to this technical report are documentation drawings of selected parts and assemblies.
|
|
|
Reinforced concrete road bridge
Koumar, Jan ; Panáček, Josef (referee) ; Koláček, Jan (advisor)
The subject of this bachelor's thesis is the design of a reinforced concrete road bridge with one span over the river Oskava in the village Unicov. The bridge will convert road II/449 category S 7.5 / 50. Two shape variants of the cross-section were designed, from which a slab with a trapezoidal cross-section and a considered span of the bridge of 14.00 m was selected for the design and assessment of the load-bearing structure. The internal forces from the applied load were calculated on a slab model in SCIA Engineer 18.1 and compared with a manual calculation on a bar model using the method of resistive widths. The load-bearing structure is dimensioned for the ultimate limit state and the serviceability limit state.
|
|
| |
|
|
Design of sand blasting machine modification
Klár, Pavel ; Fuis, Vladimír (referee) ; Krejsa, Jiří (advisor)
This thesis is focused on design and implementation of structural adjustment of sandblasting machine with regard to the requirements of resolution. The first part consist of short study describes a blasting technology and various types of blasting machines. Second part – practical part consists of problem analysis and setting goals to be achieved. The main goal of the design is to not influence the machine and to limit presence of the operators by modification in the actual process of sanding. There is also detailed design of solution’s proposal which fulfills the specified goals and is supported by calculations. Descibed design was realized and preliminary results suggest that pre-defined goals are met.
|
|
| |
|
|
Mechanical barrier project
Kubeš, Ondřej ; Škopán, Miroslav (referee) ; Malášek, Jiří (advisor)
The first part of the thesis analysis is about the most common concepts of barriers which restrict the passage of vehicles. These provide security for parking cars. On the basis of this analysis is made design of road barrier. This proposal is accompanied by the plan.
|
|
|
Car show room in Olomouc
Mudrák, Štěpán ; Barnat, Jan (referee) ; Šmak, Milan (advisor)
The subject of this diploma thesis is structural design of a car showroom building in Olomouc. The layout dimensions are 16 x 37 m, the roof is designed as a 5° slope half span roof with cantilever hanging of 6 m. Roof layout dimensions are therefore 22 x 37 m. The object is designed as a two – storey building with two levels of second floor. Maximum height of the structure is about 9,0 m. The design is based on a study of two materiál variants – timber and steel structure. More suitable variant was chosen and following drawings, structural design report and technical report were processed. Main structural system is designed as a one rigid corner column – girder connection, 6 m axis dimensions. Main structural material is a glued laminated timber, completed with coniferous timber and steel elements. The roofing is supported by rafters which are connected to the main roof truss. Bearing element of floors is a Novatop Element structural systém. The spatial rigidity of structure is ensured by steel stiffeners. Structural analysis was carried out by finite element method in software Scia Engineer 21, where the design of the basic elements for ultimate limit state and serviceability limit state was made. Connection design was processed manuály and with software Idea Statica and Hilti Engineering Suite.
|
guest ::
