|
|
Influence of anticorrosive surface treatment of steel reinforcement fibers on the properties of ultrahigh-performace cement composite
Bocian, Luboš ; Ptáček, Petr (referee) ; Novotný, Radoslav (advisor)
This thesis characterized surface layer of brass on commercially available steel microfibers. Subsequently, it was studied how to remove this surface layer of brass off these microfibers. Additionally, this thesis investigated influence of removal of brass surface layer on mechanical and ballistic properties of RPC composites. It was also studied how previously mentioned surface layer of brass influences interface between steel microfibers and matrix. It was found out that the surface layer of brass on commercially available steel microfibers is uneven and that the brass fills scratches present on steel underneath the surface layer of brass. It was also found out that conc. HNO3 and mixture of NH3 and H2O2 in volume proportion of 3 : 1 can be used to remove the surface layer of brass. The only thing to consider is that steel microfibers from conc. HNO3 corrode. Flexural strength of composite made with fibers from mixture of NH3 and H2O2 is higher than flexural strength of composite made with commercially available steel microfibers with surface layer of brass after 28 and 95 days. Compression strength wasn’t significantly affected in any composite used in this thesis after 28 and 95 days. Composite made with fibers from mixture od NH3 and H2O2 showed slightly better ballistic resistance than composite made with commercially available steel microfibers with surface layer of brass. In terms of SEM analysis of interface between matrix and steel fibers of certain composite, it was found out that there was no evidence of infiltration of components of brass into matrix.
|
|
|
Utilization of fluidized bed combustion solid residues in the production of refractories
Tvrdý, Michal ; Novotný, Radoslav (referee) ; Opravil, Tomáš (advisor)
The thesis deals with the preparation, study and analysis of refractory ceramics, namely fireclay mortars for stove purposes with the addition of fluid ash. The mixtures for preparation of refractory ceramics were doped with different content of fly and bed fluid ash in order to reduce the consumption of the original raw materials for the preparation of these materials. Fired slate clay, refractory clay, fly and bed fluid ash were used for preparation the samples. Input raw materials and fired fireclay mixtures were characterized by XRD, TG-DTA-EGA, TDA, SEM-EDS, heat microscopy, isothermal calorimetry, ICP-OES. The mechanical properties, i.e. compressive strength and tensile bending, were also determined on fired fireclay mortars. The results showed that the properties of the fireclay mortar containing fly ash are comparable to the starting mortar to a specific ash dosage. It has also been found that bed fluid ash is not suitable for the production of refractory materials.
|
|
|
Chemical wall clamp based on fast-setting geopolymeric binders
Novotný, Radoslav ; Kalina, Lukáš (referee) ; Šoukal, František (advisor)
The aim of this work is to develope fast-setting geopolymeric binders applicable in the chemical wall clamp. This clamping systems are big trend because of easy application, ability to transfer big forces and short setting time. Binders of this systems are based on polymeric resin. Their raw materials are expensive, toxic and flammable substances. Based on this consideration an anorganic fast-setting geopolymeric binder was developed. This binders consist of mixture of metakaolin and precipitated silica activated by potassium hydroxide. Binder were characterized by suitable analytic methods (XRD, SEM, DTA). The results of this metods were used for optimalization of binder properties.
|
|
|
Issues of stopping the hydration of alkali-activated slag using organic substances
Chadima, Jan ; Novotný, Radoslav (referee) ; Bílek, Vlastimil (advisor)
This thesis deals with the stopping of hydration of alkali activated slag by organic solvents and investigates to what extent the selected organic solvent affects the results of the analyses. The solvents used were acetone, diethyl ether, ethanol, isopropanol and methanol, and this is because these are the most commonly used organic solvents in practice. Thermogravimetric analysis along with differential thermal analysis was used to assess the degree of influence of organic solvents on the alkali activated slag and Portland cement samples. Methanol and acetone affected the samples the most and the longer the sample was stored in the solvent, the more it reacted with the organic solvent. The adverse interaction of organic solvent was greatest for the Portland cement samples. Samples that were rinsed with diethyl ether prior to analysis had lower mass losses than samples that were not rinsed. In the case of alkali activated slag, it was found that the way in which the thermogravimetric results were affected by organic solvents was highly dependent on the activator used, with the smallest effect observed for Na2CO3 activation, while the largest effect was observed for NaOH activation at temperatures below 600 °C, and for higher temperatures for water glass activation.
|
|
| |
|
|
The study of sulfate depletion in cement binders
Jurko, Michal ; Švec, Jiří (referee) ; Novotný, Radoslav (advisor)
This bachelor thesis deals with the study of sulfate depletion in cement binders. Basic knowledge about cement binders is summarised at the beginning of the theoretical part. The theoretical part goes on to describe the hydration of Portland cement (PC) and to briefly describe the influence of different types of milling on PC particle size. In the experimental part, PC fractions of various average particle sizes were prepared on a planetary ball mill for wet conditions. On the prepared cement, their hydration was studied using isothermal calorimetry; especially sulfate depletion, portlandite precipitation, heat flow rate and induction period interval. n the thesis were also used analyzes for autogenous shrinkage, XRD and STA. The input raw materials are cement CEM I 42,5 R (grey, Českomoravský cement, a.s. – Mokrá, Czech Republic) and sulfate-resistant cement CEM I 52,5 R (white, Aalborg Portland, a.s. – Aalborg, Denmark). On the basis of the results analysis, a proposal was made to correct the presence of sulfate ions by adding gypsum in these cements. In the case of CEM I 52,5 R the correction is recommended and in the case of CEM I 42,5 R the correction is necessary.
|
|
|
Influencing the hydration of high-performance composites using zinc ions
Všetečka, Tomáš ; Hajzler, Jan (referee) ; Novotný, Radoslav (advisor)
The bachelor thesis is focused on the influence of hydration of high-performance cementitious composites, more specifically reactive powder composites. Zinc ions were supplied by the compounds of zinc oxide and zinc sulphate heptahydrate. Zinc ions were added by weight content to cement at concentrations of 0.2; 0.5 and 1.0 wt. %. The development of properties depending on the content of zinc ions and the type of compound used was monitored in this work. The measured values were compared with reference values that did not contain zinc ions. The highest compressive strengths were obtained with a sample containing 1.0% Zn in the form of zinc oxide. However, this sample is associated with a longer setting time due to the retarding effect of zinc ions on hydration. The retardation effect was monitored using isothermal calorimetry. For samples containing zinc ions, a negative effect on the brass layer of steel fibers, which was used as reinforcement, was observed. Due to the addition of zinc ions, dezincification and subsequent removal of brass from the surface of the fibers took place. Therefore, these specimens had lower tensile strengths. A positive effect on the differential ballistic protection efficiency factor was observed for a sample containing 1% Zn in the form of zinc oxide.
|
|
|
High performace cement composites with increased abrasion resistance
Baranov, Dmitry ; Šuleková, Nikola (referee) ; Novotný, Radoslav (advisor)
The bachelor thesis deals with the effect of addition of potassium hydroxide solutions of different concentrations to HPC composites. The study focused mainly on parameters important for the abrasion of the composite such as surface hardness, which was measured in two ways. The first is by using of a manual hardness tester, the second is by a notching method through a drill with a tungsten carbide crown. The samples with the highest concentration of potassium hydroxide had the best results. It was assumed that the cause could be a very thin (400 1000 nm) dense layer on the surface with a predominant content of sulfur and potassium compounds, which was shown on an electron microscope. In addition to the hardness of the surface, other mechanical properties important for cements were monitored. Samples with different KOH concentration were tested for compressive and flexural strength.
|
|
|
A study of the hydration of calcium aluminate cement in an excess of silica fume
Nehéz, Samuel Emil ; Švec, Jiří (referee) ; Novotný, Radoslav (advisor)
This thesis deals with the effect of silica fume (microsilica) on the hydration process of alumina cement (CAC). During the preparation of the samples, the effect of the amount of microsilica and the effect of the hydration temperature on the formation of hydration products were investigated. Microsilica was always in excess compared to alumina cement. The characterization of the raw materials was carried out using particle size measurement and calorimetry. In the case of the samples themselves, calorimetric measurements showed that the hydration process is divided into two separate events. Thanks to this, it was possible to stop the hydration at the desired time and examine the emerging hydration products. The presence of silica fume caused the formation of characteristic hydration products - strätlingite (C2ASH8). It was found that as the temperature of hydration increases, the resulting products form more quickly. Increased hydration temperature had a negative effect on mechanical properties. The properties and characterization of the prepared samples were further investigated using XRD, TG-DTA and scanning electron microscopy (SEM).
|
|
|
Influencing the hydration of high-performance composites using zinc ions
Všetečka, Tomáš ; Hajzler, Jan (referee) ; Novotný, Radoslav (advisor)
The bachelor thesis is focused on the influence of hydration of high-performance cementitious composites, more specifically reactive powder composites. Zinc ions were supplied by the compounds of zinc oxide and zinc sulphate heptahydrate. Zinc ions were added by weight content to cement at concentrations of 0.2; 0.5 and 1.0 wt. %. The development of properties depending on the content of zinc ions and the type of compound used was monitored in this work. The measured values were compared with reference values that did not contain zinc ions. The highest compressive strengths were obtained with a sample containing 1.0% Zn in the form of zinc oxide. However, this sample is associated with a longer setting time due to the retarding effect of zinc ions on hydration. The retardation effect was monitored using isothermal calorimetry. For samples containing zinc ions, a negative effect on the brass layer of steel fibers, which was used as reinforcement, was observed. Due to the addition of zinc ions, dezincification and subsequent removal of brass from the surface of the fibers took place. Therefore, these specimens had lower tensile strengths. A positive effect on the differential ballistic protection efficiency factor was observed for a sample containing 1% Zn in the form of zinc oxide.
|
guest ::
RSS feed.