|
| |
|
|
Oil flow simulation in gearbox
Blažek, Martin ; Prokop, Aleš (referee) ; Řehák, Kamil (advisor)
Lubrication is one of the most important features of designing the transmission and has a great influence on the correct function and long lifetime of bearings and gears of geared transmission. This thesis was focused on the influence of shape of single-speed gearbox case with splash lubrication on oil distribution and churning loss of gear wheel and pinion. Experiences from previous simulation were used to perform oil flow simulations of automotive gearbox test rig. The Particleworks software using the moving particle semi-implicit method was used to simulate and visualize the results. The results of this work can be used as indicators of the influence of the shape of gearbox casing on churning loss and oil distribution, and also as a design idea for appropriate placement of inspection windows in gearbox test rigs.
|
|
|
Testing of Vehicle Suspension Components
Šidla, František ; Blaťák, Ondřej (referee) ; Hejtmánek, Petr (advisor)
This bachelor thesis deals with issues related to testing car chassis components during development. Automobile transport is the most common type of long-distance transport. That's why vehicles are constantly evolving to provide the best possible performance. Increasing demands on consumers are being placed on vehicles because of the introduction of modern technologies. New technologies and concepts need to be thoroughly tested that they can be properly integrated into existing models. Test devices for determining the characteristics of the chassis are generally described here using specific examples of individual machines. Subsequently, the work clarifies the testing of the service life of individual parts of the chassis. The last part is devoted to the conceptual design of a simplified hydraulic device for testing coil springs. From the calculated characteristics, a hydraulic actuator and pump are selected from the relevant catalogues. In conclusion, the importance of car testing in development is summarized, individual types of testing are described and the readiness of test devices for the future is indicated.
|
|
|
Testing of Distance Protection
Řehoř, Jiří ; Topolánek, David (referee) ; Orságová, Jaroslava (advisor)
The testing of distance protection in bachelor´s task is made a distinction between protection, requirements and relegation. This testing is also consisted in principle of function, describing terms of distance protection and comparing with time-current characteristics. The next step after short estimation was describing digital distance protection SIPROTEC 7SA511. The advantages are included in this estimation. The next part contains some configurations and connections with a test equipment in order to take control of measuring through the computer. The extended configurations are also comprised of two programms – DIGSY and TZO3. We had to make a suggestion of suitable methodics for measuring a time-current characteristic. We carried out three measurements where the test equipment was set to role of type TREND. A magnitude is generated at the output that is changed linearly in time with required rate (speed). We changed a current IX1 for our measurements that was undertaken with a rate of current rise. This process was given by a test equipment when the set values were constant. In the second measurement we modified a size of shift phase in the test equipment. In the third measurement we tried to set up different sizes of particular impedance characteristics (zone) inside of the distance protection where was set a neutral breaking time for the measured zone. On the contrary, the previous measurements had an absolute time.We have introduced evaluated results of measuring and observations in the end of this bachelor’s thesis.
|
|
|
Test Equipment for Solder Joint Strength Measuring
Čechák, Ondřej ; Špinka, Jiří (referee) ; Starý, Jiří (advisor)
This master thesis introduces the problematics of the tensile strength of soldered joints and the correlative mathematical formulas and the use of mentioned problematics in the technology of die shear/pull machines designed for the solder joint tensile strength measurement. It explains the importance and reasons for the use of this technology. The emphasis is then laid on the design and construction innovations of the current laboratory manual shear/pull measuring machine, its semi-automation and the possibility of utilizing the innovated system in a laboratory class of a subject on FEEC BUT.
|
|
|
Design of the test facility
Pavluš, Martin ; Pavlík, Jan (referee) ; Tůma, Zdeněk (advisor)
The thesis deals with the design of automated testing equipment of selected types of pneumatic valves. The problem of manual control process is its inefficiency, both in terms of human error rate and time loss caused by further assembly. The automated manual inspection process eliminates the problem. In the theoretical part, the types of switchgear are described, selected measuring procedures and methods of measurement are described. In the practical part, the measuring procedure was set out and on the basis of it there were designed variants of the testing machine and test circuit. The conclusion of the thesis contains evaluation of the whole project.
|
|
|
Universal Tester of Radio Conditions for Narrowband IoT Communication Technology
Možný, Radek ; Štůsek, Martin (referee) ; Mašek, Pavel (advisor)
Technology Narrowband IoT is a representative LPWA (Low Power Wide Area) tech-nology that due to its promising features aims for demands of the Internet of Thingsapplications for autonomous data sending from sensors in areas of poor mobile coverage.For such applications, it is beneficial to firstly map properties of communication technol-ogy in areas of intended use and evaluate whether or not is this technology applicable.This Master thesis deals with the design of the hand-held measuring device for evaluationof Narrowband IoT properties. The output of this thesis is firstly comparison of LPWAtechnologies secondly, design of the mentioned device and verification of its functional-ity. And in last part description of measurement of transmission delay for delay-tolerantapplications. Transmission delay is a critical parameter for delay-tolerant applications.Such an application can be, for example, smart electrometers for which there is definedmaximal allowed transmission delay of 10 seconds and therefore it is desirable to evalu-ate whether or not is the deployment of the communication technology Narrowband IoTsuitable in the intended area for delay-tolerant or even for delay-intolerant applications.
|
|
|
Testing of service life of the bolt fastening used in electron microscopy
Habarka, Ondrej ; Radoš, Jiří (referee) ; Krejsa, Jiří (advisor)
Cílem této bakalářské práce je vybrat vhodný materiál a jeho povrchovou úpravu pro šroubový spoj s jemným závitem na držáku vzorku v elektronovém mikroskopu. První částí je přehled použitelných materiálů a povrchových úprav, které jsou nemagnetické, tudíž neovlivňují elektronový paprsek v mikroskopu. Dále se práce zabývá tvorbou testovacího zařízení na testování životnosti jednotlivých vzorků závitových tyčí. Výsledkem práce je porovnání testovaných materiálů a výběr jednoho nejvhodnějšího pro reálné použití.
|
|
|
Design of equipment for measuring aerodynamically relevant parameters of passenger car tire
Kojecký, René ; Blaťák, Ondřej (referee) ; Vančura, Jan (advisor)
This diploma thesis deals with the issue of measuring tire parameters and their impact on vehicle aerodynamics. The aim is to create a design of the tire test equipment together with a suitable method for evaluating obtained results. The theoretical part provides an overview of currently used tire testing methods. The market research follows in order to select suitable components for the proposed measuring station. The output of the practical part of the work is the assembly of the solver in the form of a Matlab script and a design with the necessary drawing documentation.
|
|
|
Laboratory simulator of radial journal bearing
Vincenc, Jan ; Čermák, Jan (referee) ; Šperka, Petr (advisor)
The master’s thesis deals with a design of a radial journal bearing simulator, which is ready to implement a transparent sapphire journal bearing to an optical observation of the oil film. The first part of this thesis contains a short review of a few currently used journal bearing test rigs. The next part of the work deals with a discussion of concept variants and a definition of important parameters. The last part contains a detailed description of the designed radial journal bearing simulator. Limitations of the designed simulator and recommendations for future improvements are also discussed. The result of the presented work is the designed journal bearing simulator which will allow observing of the oil film. The work also consists a complete design documentation.
|
guest ::
