|
|
Design of semiconductor optical amplifier
Somora, Rastislav ; Hanák, Pavel (referee) ; Slavíček, Karel (advisor)
Diploma thesis deals with the construction of a moder semiconductor optical amplifier SOA. In the first chapter optical comunication and the use of optical amplifiers is described. In the next chapter some types of optical fibers, their chemical composition and properties are described in detail. The third chapter overviews optical amplifiers, their use today, describes their advantages and disadvantages and their proper use in optical comunications. The fourth chapter describes the solution of the objective, the right layout of separate blocks and connections used in measurements. Fifth chapter describes used components, describes their basic parameters and proper use in circuit. The last chapter evaluates outputs of measurements and their impact on the objective.
|
|
|
OTDM to WDM conversion
Kupčiha, Lukáš ; Křepelka, Václav (referee) ; Filka, Miloslav (advisor)
The aim of this thesis was introducing the options of conversion between OTDM and WDM technologies. Since this issue is rather extensive, first of all the principle of optical transmission system is described. One chapter presents the effects influencing the optical transmissions. Material absorption, linear and nonlinear scattering and bending losses are mentioned in terms of fiber losses, followed by description of waveguide, chromatic and polarization-mode dispersion of optical fibers. Last part of the chapter presents nonlinear effects, including self-phase modulation, cross-phase modulation and four-wave mixing. The practical part of the thesis deals with multichannel systems. The principles of frequency, space a hybrid multiplexing are explained. Multichannel systems with optical time domain multiplexing and waveguide multiplexing are described in detail and compared. The elements of the transmission chain of multiplex, such as different types of lasers, detectors, modulators, optical amplifiers, splitters, couplers, MUX and DEMUX are discussed. The next part of the thesis was aimed at suggesting the model of mutual conversion between OTDM and WDM systems. First of all, the previously performed experiments concerning the conversion between OTDM and WTM were evaluated. Then the model of OTDM/WDM/OTDM conversion was designed, with explanation of its parts and their function. The general recommendations for practical implementation were are also included. Due to the limited amount of time reserved for access to the simulation program Optsim, the simulations were performed only for certain parts of the proposed conversion model. At the end of the thesis, the proposed model is evaluated.
|
|
|
CWDM technology for optical wireless links
Kumpán, Vítězslav ; Zvánovec, Stanislav (referee) ; Wilfert, Otakar (advisor)
In this work an optical wireless test link for studying of atmospheric phenomena in the optical bands of 830 nm and 1550 nm is described. The WDM technology involving technology of optical fibers is included into transmitter of the link. The measuring devices for measuring power, spectrum and polarization control are included into receiver of the link. The outcomes of this work are both measuring chain design and verification of its functionality.
|
|
|
Optical amplifiers for metropolitan and access networks
Čech, Martin ; Šporik, Jan (referee) ; Tejkal, Vladimír (advisor)
Aim of this Master´s thesis is to describe and compare most common types of optical amplifiers used in today’s networks. The first section focuses on problematic of optical transmissions and phenomenon which cause degradation of transmitted signal. It is also explained in this section why there is a need to deploy optical amplifiers. Next section describes basic principles, structure and properties of individual types of optical amplifiers. Following section describes simulations which were made to compare the performance of transmission systems with each individual type of optical amplifier. The last section contains a design of optical metropolitan network with wavelength multiplex. Based on simulations from preceding part best amplifier type and optimal amplifier placement was selected. Functionality of the design was tested and simulations described in final section.
|
|
|
Design of Passive Optical Network
Asensi Pla, Juan Salvador ; Reichert, Pavel (advisor)
El constante incremento en la demanda de servicios de banda ancha y el consecuente aumento del volumen de tráfico que se genera en nuestras redes de comunicaciones, han motivado la necesidad de implementar redes de nueva generación en nuestros territorios. El presente proyecto final de carrera tiene como objetivo explicar el diseno y la planificación de una red pasiva de fibra óptica (PON). La idea principal de este proyecto es construir un entorno ficticio que nos permitirá profundizar en detalle en las redes FTTx y decidir cuál es la opción más optima para este entorno. Para hacer esto posible, en primer lugar se va a hablar sobre el elemento principal de estas redes, la fibra óptica, para conocer con detalle sus principios de funcionamiento y sus características más importantes. La parte teórica seguirá con la definición de las redes FTTx y las configuraciones punto a punto y punto a multipunto, para pasar a hablar detenidamente sobre las redes PON y concluir cual de sus tecnologías será la más optima hoy en día. Por último, entraremos en la parte práctica en la que se elegirá un software de simulación que se ajuste a los requisitos de diseno, se realizará el diseno de la red óptica pasiva y se obtendrán los resultados de simulación que justifiquen que la red es viable y puede ser implementada en un caso real.
|
|
|
Design and management of WDM systems for optical networks
Červenka, Vladimír ; Šporik, Jan (referee) ; Tejkal, Vladimír (advisor)
This thesis describes single types of wavelength-division multiplex (WDM) according to the International Telecommunication Union (ITU-T). This work offers an overview of components and evaluation of critical parts of network design utilizing WDM technology. There are depicted typical properties, suitable components and channel spacing for each category. Suitable optic fibers according to ITU-T and characteristics of negative effects can be found in the work as well. Furthermore, there are presented most important optic sources, optic amplifiers, optic detectors with filters their requirements and application. They are especially important for achieving operation of WDM system. The fifth chapter considers impact of negative effects in fiber optics and their influence on the system. Then, a WDM system is designed along with management and monitoring the physical layer. The work also presents 1,33 Tbit/s (32 × 42,7 Gbit/s) WDM transmission over 300 km (with three 100 km spans) of post-compensated non-zero dispersion-shifted fiber (NZDSF) LEAF. The capacity of 400 Tbit/s×km is achieved in a single 25,6 nm C band using non-return-to-zero differential phase-shift-keyed modulation (NRZ-DQPSK), balanced detection and erbium-doped fiber amplification. Together with design of transmission system a several simulative analysis has been carried out in order to find the optimum configuration (such as number and distances between amplifiers, length of spans or the way of dispersion compensation) for a high bit rate optical transmission system. It was used a program OptiSystem 8.0.
|
|
|
Design of Multiplex Optical Fibre Link
Krejča, Libor ; Křivánek, Vítězslav (referee) ; Kyselák, Martin (advisor)
In this thesis I consider problems of optical multiplexers, optical amplifiers and designing optical networks with this components. CWDM and DWDM are the most common used multiplexers today. I describe principles of realization multiplexers from basic level to realization in WDM networks. EDFA is also common used amplifier today and I describe his internal structure and how it works. Today, we can observe many realization of optical netwoks with Raman amplifiers, especially in long haul networks. Raman amplifier is characterized in brief. In next chapter I describe the design of optical communication systems and the main designing equations are explained. Then I used the equations for example of designing optical communication system with multiplexers, EDFAs and other components, which are needed for function of the system. In last chapter I explain mathematical model of signal propagation in optical fiber called nonlinear Schrodinger equation, which includes main optical effects in fiber like chromatic dispersion or Kerr effect. The simulation model and his numeric solution was designed including PMD effect, the simulation model is programmed in MATLAB.
|
|
|
The data transfer technologies in optical access networks (FTTx)
Matušík, Lukáš ; Míča, Ivan (referee) ; Reichert, Pavel (advisor)
The objective of diploma thesis is describe problems connected with designed of FTTX networks and bring the reader problems of data transmission in optical acces networks the type of PON. In the introduction are mentinoned individual technologies that already operate, and there are describe advantages disadvantages of the use topology point-to-point and point-to-multipoint. In the following chapters are dealt with problems with data broadcasting in the direction from final participant. In the other part of diploma thesis are described elements, that were used for the proposed transmission route. The own PON acces network was presented on the basis information obtained by comparing the various networks and the elements involved in them. The network presented in conclusion diploma thesis is involved in topology point to multipoint. This transmission route is simulated in the program that allows the involvement of network by the user’s need with real values. The acces network is simulated for different transmission speed and different distances. The assesment of created optical route results from the measured values, theirs source is program OptiSystem, these values are summarized in the final chapter.
|
|
|
Model of the metropolitan optical network
Prudík, Jiří ; Hudcová, Lucie (referee) ; Křivák, Petr (advisor)
The purpose of this master’s thesis is foremost to provide a simple guide how to build elements of optical metropolitan area network. The basic model consists to sequence of construction, network topology, passive and active parts. The collection contains examples of alternative technology such as Wireless LAN with different frequency. The optical network construction based on optical cable, fibres, splices, trays, adapters, connectors and active parts for example a lot of media convertor models. After that there are demonstrating type of wavelength division multiplexer used in metropolitan area network – passive planar PCL splitter. One of the passive planar splitter are used to increase optical fibre channel. At the end of the collection a simplified examples of used measurements – optical time domain reflectometry and optical fibre transmission. Contains standard protocols or reflectogram. The conclusion of this thesis summarizes costs of FTTb (Fibre To The Building) model of optical metropolitan area network in Czech republic and future contribution for society.
|
|
|
Effect of optical connectors quality on transmission
Bernkopf, Miroslav ; Křepelka, Václav (referee) ; Filka, Miloslav (advisor)
This diploma thesis deals with optic fiber connectors and their influence on transmissions realized via fiber optics. Optical fibers and lightguides play the key role in telecommunications because of constant demands of higher bandwidth and data rates. Original metalic wires do not meet market requirements and so the fiber optics are more and more being used. There are various types of fibers and there are also many ways of connections. This work deals with demountable way of connection – optical connectors, which have the biggest influence on a total attenuation and route length. Connector has to meet various requirements such as cleannes, quality, mechanical construction and ferrule polishing.
|
guest ::
