|
|
Manufacturing of the TV Wall Bracket
Gregor, Radek ; Štroner, Marek (referee) ; Peterková, Eva (advisor)
The master 's thesis deals with the design of a tool for a TV bracket with an expected production of 300,000 pieces per year. After a review of possible production technologies, production in a progressive compound tool that combines shearing and bending was chosen. DC01 material with a thickness of 2 mm in coil was selected for the production of the part with a 52.23% utilization according to the selected cutting plan. Then, a manufacturing process was established for the production of the part, which will be made in six steps. Furthermore, the total forming force of 893,1 kN and the forming work of 1355,8 J were calculated. The mechanical press was equipped with an automatic material feeder ARPL RAL 250 from Attl a spol s.r.o. After the design of the combined progressive tooling, the functional dimensions were determined and control calculations for the critical sections were performed, all of which were met.
|
|
|
Manufacturing of kitchen sink
Vágner, Lukáš ; Peterková, Eva (referee) ; Jopek, Miroslav (advisor)
The project deals with the design of production of the kitchen sink made of chromium-nickel austenitic steel 1.4301. Material thickness of the sink is 1 mm. The annual production series is 30,000 pieces. After considering the size of the produced series, a combination of shearing and deep drawing was chosen as the production technology. Shearing of the circular shape was combined with the execution of both draws into one production tool. For this design, the necessary calculations were performed along with verification by simulations in the PAM-STAMP program.The tool is clamped in a hydraulic press PO 400, which has all the necessary parameters. The coil blank is guided through the unwinding and straightening device Compact Line GLK3-1000. The selling price of one sink was set at CZK 1,300. Production becomes profitable after producing 7540 sinks.
|
|
|
Manufacturing of metal yoke of electrical socket by compound tool
Svozilová, Lucie ; Řiháček, Jan (referee) ; Peterková, Eva (advisor)
The project elaborated design of technology production of the metal yoke of electrical socket made of steel DX51D + Z200 by compound progressive tool. Stock material for series of 200 000 pieces is a strip of coil. Manufacturing is realised in five steps consist of cutting, bending and flanging. For flanging was constructed a special mechanism for whose is necessary to use hydraulic counterholder, which is sold as a special peripheral equipment of manufacturing machine. The machine choice was adapted to this criterium. The servopress DSF-N1-800A was chosen as a manufacturing machine, which is made by AIDA company. The press can produce force of 800 kN and make work of 4000 J. Selling price of a one yoke is 24,5 Kč when the profit is one hundred percent. The break-even point comes with 58 140 made piece.
|
|
|
Manufacturing of the turnbuckle of chain
Ondráček, Pavel ; Jopek, Miroslav (referee) ; Peterková, Eva (advisor)
The diploma thesis is focused on the design of the production technology of a chain tensioner. It is a spatial component made of 1.5 mm thick steel sheet with galvanized surface treatment. DC01 steel was selected as the most suitable material. When considering the production technologies, the production in a combined process tool was selected as the most efficient one for the series of 20,000 pieces. Regarding the tool of more complex design including springs, the production will be done in four steps on the LEN 63 eccentric press with accessories used for feeding and unwinding the metal sheet belt from the coil. The final price of the chain tensioner including the bolt and two nuts is 26 CZK.
|
|
|
Forming technologies of non-ferrous materials
Zuhla, Michal ; Dvořák, Milan (referee) ; Císařová, Michaela (advisor)
This work is focused on the surface forming, in particular, non-ferrous metals. There are described methods of cutting, drawing and bending. For each of these methods are listed and summarized the issues. There are also given individual production technologies cutting, drawing and bending, along with examples of products and their use. The work is complemented with an overview of the most important non-ferrous metals. For these metals are described their properties, suitability for molding and their alloys.
|
|
|
Production of joint folded out the rule
Šoukal, Hynek ; Podaný, Kamil (referee) ; Žák, Ladislav (advisor)
Project developed within the bachelor study presents a proposal production technology of joint folded out the rule from construction steel 12 060. Thick is 0,5 mm and the production ran is specify at 30 000 units a year. In accordance with literature studies and by calculations have been designed a combined roll forming tool, which consists of a rack with two pillars. This tool will be fix in on eccentric press LEN 10C by SMERAL, Trnava, with nominal press force 100 kN. Trimming punches, holding punch and bending puch are made of tool steel, grade 19 436.3. Lower functional part of the tool ass well.
|
|
|
Design of Tool for Louvers Production
Hejna, Jaroslav ; Žák, Ladislav (referee) ; Řiháček, Jan (advisor)
This thesis presents a tool design for production of embossments into the bottom part of the agricultural silo made of Dx51D material. The research analysis all technologies used for embossing, that is cutting and shallow drawing. This is followed by a chapter on simulation. The tool design itself is described. Its principle is based on tools for punching machines. The upper half of the tool is composed of a weldment to be clamped into pressing machine, into which are mounted functional parts in the form of inserts. The lower tool consists of several bolted plates, punches and a holding plate, which is located on the springs. In order to achieve correct design, necessary calculations were carried out and it was all confirmed by simulation in ANSYS. The two tool halfs are guided by pins attached at the edges of the lower tool. The technical - economical evaluation compares the work of the proposed tool with other possibilities of embossing.
|
|
|
Manufacturing of a Cable Holder
Šimka, Radek ; Žák, Ladislav (referee) ; Řiháček, Jan (advisor)
The bachelor’s thesis proposes a design for the production technology of the cabling holder, situated in the outdoor part of the air conditioner. This product is made of steel sheet DC01 with a thickness of 1 mm. The production of this holder is set to be 200 000 pieces per year. A progressive die tool was selected as the most suitable type of production technology, based on a literature study of various production technologies. This enables to combine cutting and bending of steel sheets with the use of one tool device. Manufacture will be performed using a mechanical eccentric press LEN 63 C. All the necessary requirements of this device are satisfactory for the production.
|
|
|
Forming Technology of Thin Sheets
Musil, Zbyněk ; Žák, Ladislav (referee) ; Dvořák, Milan (advisor)
This bachelor‘s thesis deals with technology of mechanical working of the sheetmetals by cutting for rotary and non-rotary single parts. The first part deal with common dissertation about surface mechanical working, mainly about cutting and meaning of cutting gap in accordance with final cutting. The second part deals with transfer of the new pieces of knowledge from foreign technical literature of surface mechanical working. In the last part there is done an aplication on the particular component.
|
|
|
The Antenna Bracket Manufacturing by a Compound Tool
Lipka, Ondřej ; Lidmila, Zdeněk (referee) ; Peterková, Eva (advisor)
This master’s thesis focuses on the concept of large-lot manufacturing of sheet metal component made from DC01 steel. Based on forethought, the method of compound tool combining shearing and bending was chosen. The theoretical part analyses used technologies in detail. In the next part specific course of manufacture was created and supplied with technological calculations. Based on all needed facts the tool was designed and after that forming machine, LDC 160 crank press, was chosen. At the end the usability of designed concept was confirmed with economical calculations.
|
guest ::
