|
|
Study of plunger pump with linear motor
Jáchym, Jan ; Uttendorfský, Petr (referee) ; Pochylý, František (advisor)
This thesis deals with study and design of plunger pump with linear motor. This pump can be used for blood pumping in heart surgery. The theoretical part of this thesis is focused on description of extracorporeal circuit, heart boosters and artificial heart. This thesis provides an overview of check valves which are used in heart surgery too. Basic equitations for pump design are derived and calculated in this thesis. The pump design and manufacturing by the 3D technology was made by previous results. Finally, in this thesis are compared theoretical results and experimental data.
|
|
|
Valve Exploiting Principle of the Side-Channel Turbine
Jandourek, Pavel ; Janalík, Jaroslav (referee) ; Varchola, Michal (referee) ; Pochylý, František (advisor)
The presented work deals with basic characteristics of the side-channel machines. The intention is to replace the pressure reducing valve by low-specific speed side-channel turbine. Thereby creating a kind of turbine valve using energy, which would otherwise be dissipated in the valve. Pressure reducing valves are the source of large hydraulic losses and their replacement is possible, because the same resistance characteristics side-channel turbine and a pressure reducing valve.
|
|
|
Modification of a blood pump as a heart replacement
Simandl, Mirek ; Fialová, Simona (referee) ; Pochylý, František (advisor)
The master’s thesis deals optimization of regenerative pump and axial pump with ring motors that are designed as a heart replacement. Analysis of the koncepts is performed which were made in previous master’s thesis. There is created a new design of construction and hydraulition with using flat motors based on the analysis. The compact assembly of two impeller was formulated that replaced left and right heart and it served as a function of heart replacement. A functional model of the pump is created, there is measured characteristics of impeller and results are compared with CFD analysis. The design requirements some parts of the axial pump are added and it’s deviced feasibility analysis.
|
|
|
Separation of rigid particles from heterogeneous suspension
Prax, Ondřej ; Debreczeni, Ondřej (referee) ; Pochylý, František (advisor)
The bachelor thesis contains a literature search dealing with the separation of solid particles from a heterogenic suspension. The first part is aimed at separation methods. Then, a chapter follows dealing with separation devices, which are used in waste water treatment plants. A more detailed description of the separator used for the separation of sand from waste waters is part of this paper. The described device serving to separate solid particles from a suspension uses the combination of sedimentation and separation methods. To visualize the separator a 3D model in Autodesk Inventor Professional 9 device was used in the presented paper.
|
|
|
Optimization of a sinusoidal pump
Sluše, Jan ; Bílek, Martin (referee) ; Pochylý, František (advisor)
The aim of the diploma thesis is to design the technical solution of minimization of frictional losses, which occur when using a sine pump at position of the shaft locking and on the impeller wheel. The losses originating from the frictional forces have a negative influence on the lifetime of individual parts and economy of the pump. In the first part the author describes sine pumps from the constructional point of view and the main producers are mentioned. The second part contains suggestions on the parameters of the pump and various possibilities of solutions. The last part covers the experiment and conclusions.
|
|
|
Verification of geometry influence on dynamic properties of immersed body
Černý, Tomáš ; Pochylý, František (referee) ; Habán, Vladimír (advisor)
Immersion of the body into the fluid creates additional effects which must be considered when designing the machines. Additional effects from the fluid influence the dynamic properties of the body. In this work the decrease of the natural frequency and the increase of the damping ratio during the gradual immersion of the body into the fluid are investigated. Diploma thesis is based on an experiment, which is performed on a series of flat strip steel components of various widths. The first three bending and first three torsion shapes of the free-hanging body are examined. Emphasis is placed on the influence of part width. In the next phase of the experiment, the influence of the proximity of the solid wall to the dynamic properties of the cantilever beam is examined. Further, the determination of the added density from the fluid is performed by modal analysis using the ANSYS software.
|
|
|
Improvement of the suction capacity of the fire-engine pump
Archalous, Jakub ; Habán, Vladimír (referee) ; Pochylý, František (advisor)
This diploma thesis deals with reducing the time of sucking water into the rotating impeller of the centrifugal pump as used in firesport. The suction is carried out by the ejector, which is powered by combustion engine exhaust gases. A mathematical model was created, which shows the flow in the ejector. It was also used as a basis for the creation of a new ejector, which has an increased airflow when getting closer to atmospheric pressure.
|
|
|
Self-priming pump 65-SVD
Goláň, Petr ; Haluza, Miloslav (referee) ; Pochylý, František (advisor)
The purpose of this diploma work is re-count the hydraulics of the pump and project well-qualified treatment of turbulent pump 65-SVD-2°. Calculations of principál dimensions impeller and side-channel are based upon the theories, experiments and finally on the knowledge gained from the test models constructed. The results of this project can be used for design necessary treatment of turbulent pump 65-SVD and follow-up connection of those pump to the production program of the Sigma pumpy Hranice s.r.o.
|
|
| |
|
|
Swirl pump as an artificial heart replacement
Čápová, Ludmila ; Fialová, Simona (referee) ; Pochylý, František (advisor)
The purpose of the diploma thesis is to establish on survey of swirl pump from previous years and his optimization via which is suggested the second degree of synchronous pump whereas they should work together like a total artificial heart. Hydraulic and constructional proposal is solved. Conception is realized experimentally also with help of CFD calculation, results are compared with each other.
|
guest ::
