|
|
Oxidation behavior adjustment for TiAl intermetallics by Al-Y multilayers
Handrk, Jiří ; Tkachenko, Serhii (referee) ; Jan, Vít (advisor)
Mechanické vlasnosti intermetalika na bázi titan hliník Ti-46Al-7Nb-0.7Cr-0.1Si-0.2Ni jsou konstatní do teploty 700 °C. Nad touto teplotou slitina oxiduje. Cílem této práce bylo zlepšit oxidační vlastnosti pomocí kovové multivrstvy na bázi yttrium hlinik. Pro depozici vrstev byla použita metoda PVD. Na vzorky byly naneseny vrstvy čistého ytria nebo kombinace yttrium, hliník. Vzorky byly následně žíhány v inertní atmosféře na 700°C a 900°C nebo nebyly. Kvalita nanesených vrstev byla zkoumána pomocí scratch testu a EDS analýzi. Dále byly vzorky izotermicky oxidovány na 900°C po dobu 100 hodin. Na vzorcích byly po oxidaci prováděny měření pevnosti v tříbodovém obybu a měření hmotnosti. Chemické složení oxidické vrstvy bylo vyhodnoceno pomocí EDS. Žádná z vrstev s nebo bez žíhání neprokázaly zlepšení oxidických vlastností. Vyšší teplota žíhání prokýzala zlepšení mechanických vlastnotí vrstvy, ale zhoršení materiálu.
|
|
|
Determination of properties of as-sprayed and EB-deposited coatings prepared by thermal spray technologies using scratch test and nano-indentation methods
Cének, Lukáš ; Tkachenko, Serhii (referee) ; Čížek, Jan (advisor)
Properties of samples and their coatings may be affected by the electron beam. This paper deals with the analysis of the microstructure, phase and chemical composition and the determination of mechanical characteristics of inconel steel substrate and CoNiCrAlY coatings deposited via different types of thermal spraying (HVOF, cold spray), in combination with modifications by the electron beam technology. During the study it was found that the deposition did not change the chemical composition. Further it was found that the interaction of the electron beam with the material did not change the chemical composition, but there is a change in the structure and a reduction of porosity and surface roughness, resulting in a change of mechanical properties such as decreasing hardness or increase of the modulus of elasticity.
|
|
|
Fabrication and characterization of solution precursor hydroxyapatite coatings deposited via hybrid water-stabilized plasma gun
Antoš, Zdeněk ; Tkachenko, Serhii (referee) ; Čížek, Jan (advisor)
Hydroxyapatite coatings have been used as a barrier between a metal core of replacement and living tissue for long time in medicine. Plasma spray is a typical technology for preparation these coatings. This thesis concerns a new plasma spray technology with hybrid system of arc stabilization (WSP-H). Simultaneously it uses an innovative method of feeding the initial material in a form of water suspension (SPPS). The aim of this thesis was to produce water solutions of hydroxyapatite and make coatings with WSP-H. These coatings were characterized in terms of their morfology, chemical and phase composition. Their biocompatibility was tested by a cultivation and an analysis of RAW 264.7 and MG-63 cells. The coatings made by SPPS have a very rough surface which is suitable for biological application. The biocompatibility testing discovered that the coatings will by tolerated in a human body very well. This method of production of hydroxyapatite coatings could be a good replacement of older methods after a better optimalisation of the processing parameters and after reaching purity of coating.
|
|
|
Advanced techniques in nanoindentation testing
Břečka, Jan ; Tkachenko, Serhii (referee) ; Čížek, Jan (advisor)
The aim of this thesis is to determine the suitability of using advanced indentation methods for various materials. These advanced measurement methods are described in detail and subsequently compared in terms of time complexity and accuracy of the elastic modulus and the hardness measurement. The tested materials were copper and silica. The comparison of the methods is carried out at different views and gives a general overview of advantages of these methods.
|
|
|
Fabrication and characterization of solution precursor hydroxyapatite coatings deposited via hybrid water-stabilized plasma gun
Antoš, Zdeněk ; Tkachenko, Serhii (referee) ; Čížek, Jan (advisor)
Hydroxyapatite coatings have been used as a barrier between a metal core of replacement and living tissue for long time in medicine. Plasma spray is a typical technology for preparation these coatings. This thesis concerns a new plasma spray technology with hybrid system of arc stabilization (WSP-H). Simultaneously it uses an innovative method of feeding the initial material in a form of water suspension (SPPS). The aim of this thesis was to produce water solutions of hydroxyapatite and make coatings with WSP-H. These coatings were characterized in terms of their morfology, chemical and phase composition. Their biocompatibility was tested by a cultivation and an analysis of RAW 264.7 and MG-63 cells. The coatings made by SPPS have a very rough surface which is suitable for biological application. The biocompatibility testing discovered that the coatings will by tolerated in a human body very well. This method of production of hydroxyapatite coatings could be a good replacement of older methods after a better optimalisation of the processing parameters and after reaching purity of coating.
|
|
|
Advanced techniques in nanoindentation testing
Břečka, Jan ; Tkachenko, Serhii (referee) ; Čížek, Jan (advisor)
The aim of this thesis is to determine the suitability of using advanced indentation methods for various materials. These advanced measurement methods are described in detail and subsequently compared in terms of time complexity and accuracy of the elastic modulus and the hardness measurement. The tested materials were copper and silica. The comparison of the methods is carried out at different views and gives a general overview of advantages of these methods.
|
|
|
Oxidation behavior adjustment for TiAl intermetallics by Al-Y multilayers
Handrk, Jiří ; Tkachenko, Serhii (referee) ; Jan, Vít (advisor)
Mechanické vlasnosti intermetalika na bázi titan hliník Ti-46Al-7Nb-0.7Cr-0.1Si-0.2Ni jsou konstatní do teploty 700 °C. Nad touto teplotou slitina oxiduje. Cílem této práce bylo zlepšit oxidační vlastnosti pomocí kovové multivrstvy na bázi yttrium hlinik. Pro depozici vrstev byla použita metoda PVD. Na vzorky byly naneseny vrstvy čistého ytria nebo kombinace yttrium, hliník. Vzorky byly následně žíhány v inertní atmosféře na 700°C a 900°C nebo nebyly. Kvalita nanesených vrstev byla zkoumána pomocí scratch testu a EDS analýzi. Dále byly vzorky izotermicky oxidovány na 900°C po dobu 100 hodin. Na vzorcích byly po oxidaci prováděny měření pevnosti v tříbodovém obybu a měření hmotnosti. Chemické složení oxidické vrstvy bylo vyhodnoceno pomocí EDS. Žádná z vrstev s nebo bez žíhání neprokázaly zlepšení oxidických vlastností. Vyšší teplota žíhání prokýzala zlepšení mechanických vlastnotí vrstvy, ale zhoršení materiálu.
|
|
|
Determination of properties of as-sprayed and EB-deposited coatings prepared by thermal spray technologies using scratch test and nano-indentation methods
Cének, Lukáš ; Tkachenko, Serhii (referee) ; Čížek, Jan (advisor)
Properties of samples and their coatings may be affected by the electron beam. This paper deals with the analysis of the microstructure, phase and chemical composition and the determination of mechanical characteristics of inconel steel substrate and CoNiCrAlY coatings deposited via different types of thermal spraying (HVOF, cold spray), in combination with modifications by the electron beam technology. During the study it was found that the deposition did not change the chemical composition. Further it was found that the interaction of the electron beam with the material did not change the chemical composition, but there is a change in the structure and a reduction of porosity and surface roughness, resulting in a change of mechanical properties such as decreasing hardness or increase of the modulus of elasticity.
|
guest ::
