|
|
Study of mechanical properties and microstructure development of fine-grained Cu and Cu alloy polycrystals
Srba, Ondřej ; Janeček, Miloš (advisor) ; Hadzima, Branislav (referee)
The objective of the thesis is the study of mechanical properties, microstructure development and corrosion resistance of technical purity copper and Cu-0.18 wt.% Zr polycrystals prepared by ECAP. The tensile tests showed that the characteristic stresses 0,2 and max increase with increasing strain imposed by ECAP. The improvement of mechanical properties is compensated by the drop of ductility in the deformed state. The microstructure after 8 passes of ECAP is almost homogeneous consisting of equiaxed grains of the average size of 200 nm. The severe plastic deformation resulted in the grain size reduction of the factor of 1000. The specimen after 8 passes contains almost 50% of high angle grain boundaries. From the thermodynamic viewpoint the deformation did not change significantly the corrosion properties. However, the corrosion in the deformed material is slower and much more homogeneous.
|
|
|
Microstructure and mechanical properties study of the finegrained magnesium alloys processed by severe plastic deformation
Šašek, Stanislav ; Stráská, Jitka (advisor) ; Hadzima, Branislav (referee)
Two magnesium alloys (Mg-4Y-4Gd-2Ca and Mg-2Y-2Gd-1Ca) with high ignition tem- perature were successfully processed by extrusion. Mg-2Y-2Gd-1Ca alloy was addition- ally processed by equal channel angular pressing (ECAP) to achieve ultrafine-grained microstructure. The effect of extrusion parameters on fraction of recrystallized grains, grain size, and texture was revealed by EBSD analysis. The presence of Mg2Ca, REH2 and Mg5RE secondary phases was proven by SEM and TEM. Microstructural condition including distribution and morphology of secondary phase par- ticles directly affected the mechanical properties. Yield tensile stress exceeding 200 MPa was achieved in each condition. Large non-recrystallized grains with strong {10̄10} tex- ture resulted in a significant anisotropy in mechanical properties. Processing by ECAP led to a homogeneous microstructure with a mean grain size below 1 µm. ECAP condition showed superior mechanical properties with a low anisotropy. The developed and analysed microstructural condition resulted in favourable mechanical properties. The studied alloys are therefore promising for the application in aerospace industry. 1
|
|
|
Preparation and Characterization of Advanced Thermally-sprayed Coatings on Magnesium Alloys
Buchtík, Martin ; Hadzima, Branislav (referee) ; Fintová, Stanislava (referee) ; Ptáček, Petr (advisor)
The proposed dissertation thesis deals with the characterization of HVOF and APS-thermally sprayed coatings prepared on the AZ31 and AZ91 magnesium substrates. The theoretical part of the thesis describes in-detail Mg substrates used in the experimental part of the thesis. There are also characterized materials and coatings based on NiCrAlY and FeCrNiMoSiC metals, WC-CoCr cermets, and YSZ ceramic materials. At the end of the theoretical part, the literary research summarizing the characterization and analysis performed on thermally sprayed coatings on Mg alloys. Based on the theoretical knowledge, the characterization of Mg substrates and deposited coatings was performed in terms of the surface morphology, microstructure, and the chemical composition using the light microscopy (LM) and scanning electron microscopy with energy-dispersive spectroscopy (SEM+EDS). The phase composition of the coatings was analyzed using the X-ray diffraction (XRD). The diffractions corresponding to the sprayed coatings were compared with the feedstock powders, i.e. materials used for the spraying of the coatings. The characterization of the prepared coatings in terms of the mechanical and tribological properties was performed. The hardness and microhardness of the coatings as well as the coefficient of friction, and the wear rate were measured. The last chapter of the experimental part deals with the evaluation of the electrochemical corrosion properties by the potentiodynamic measurements in a 3.5% NaCl solution. In the case of exposed samples, the evaluation of the surface and coating/substrate interface was performed using LM and SEM with EDS. The mechanism of the corrosion attack and degradation was determined from the acquired knowledge and base on the results of the short-term measurements. Based on the measured results, it can be stated that the deposited coatings were successfully applied on the surface of both Mg alloys. All the coatings increase the surface hardness of the Mg alloys and significantly improve their tribological properties. However, except for FeCrNiMoSiC coatings, the corrosion properties of Mg alloys deteriorate due to the fact that the corrosion environment can pass through the coating to the less noble Mg substrate and the corrosion microcells are created.
|
|
|
Preparation and Characterization of Fluoride Conversion Coatings on Biodegradable Magnesium Alloys
Drábiková, Juliána ; Hadzima, Branislav (referee) ; Brezinová,, Janette (referee) ; Ptáček, Petr (advisor)
The submitted work is aimed at the unconventional fluoride conversation coating preparation on the AZ31, AZ61, ZE10 and ZE41 magnesium alloys by their immersion in Na[BF4] molten salt. The influence of the preparation parameters (such as temperature and time) on the quality of the fluoride conversion coating is investigated. Methods of light and scanning electron microscopy were used for the evaluation of morphology, chemical composition and thickness of the coating. Short and long-term corrosion tests were executed to analyze the corrosion performance in simulated body fluid solution at 37 ± 2 °C with and without the fluoride conversion coating. The short-term behavior was evaluated by potentiodynamic tests, namely by the linear polarization. Long-term performance was assessed by electrochemical impedance spectroscopy or immersion tests. The coating preparation parameters influence on the character of the formed fluoride conversion coating was defined based on the obtained results. The next part of the thesis deals with the description of the possible mechanism of formation and kinetics of growth of the unconventional fluoride conversion coating on the selected AZ61 magnesium alloy. In this part, further detailed analyses were carried out to investigate the microstructure and chemical composition of the fluoride conversion coating using focused ion beam, transmission electron microscopy and X-ray photoelectron spectroscopy.
|
|
|
Electrochemical corrosion characteristics of Mg-Zn systems prepared by powder metallurgy
Kotek, Jakub ; Hadzima, Branislav (referee) ; Fintová, Stanislava (advisor)
The diploma thesis deals with evaluation of electrochemical corrosion characteristics of Mg-Zn systems prepared by powder metallurgy in SBF solution. The main aim of the thesis is to analyze the influence of chemical composition, achieved structure and parameters of the process of production of Mg-Zn systems on their electrochemical corrosion characteristics. The basic electrochemical properties of the prepared materials will be evaluated by electrochemical impedance spectroscopy. In order to clarify the mechanism of corrosion of materials, the immersion tests will be used, accompanied by metallographic observations.
|
|
|
Study of ultrafine-grained materials prepared with different methods of severe plastic deformation
Krajňák, Tomáš ; Mathis, Kristián (advisor) ; Hadzima, Branislav (referee) ; Kalvoda, Ladislav (referee)
Title: Study of ultrafine-grained materials prepared with different methods of severe plastic deformation Author: RNDr. Tomáš Krajňák Department: Department of Physics of Materials, Faculty of Mathematics and Physics, Charles University in Prague Supervisor: Doc. RNDr. Kristián Máthis, PhD., Department of Physics of Materials, Faculty of Mathematics and Physics, Charles University in Prague Abstract: Interstitial free steel with ultrafine-grained (UFG) structure was prepared by high-pressure torsion (HPT). The development of the microstructure as a function of the number of HPT turns was studied at the centre, half-radius and periphery of the HPT-processed disks by X-ray line profile analysis (XLPA), positron annihilation spectroscopy (PAS) and electron microscopy. The dislocation densities and the dislocation cell sizes determined by XLPA were found to be in good agreement with those obtained by PAS. The evolution of the dislocation density, the dislocation cell and grain sizes, the vacancy cluster size, as well as the high-angle grain boundary (HAGB) fraction was determined as a function of the equivalent strain. It was found that first the dislocation density saturated, then the dislocation cell size reached its minimum value and finally the grain size got saturated. For very high strains after the...
|
|
|
Optimization of properties of Ti based alloys for biomedical and structural applications
Stráský, Josef ; Janeček, Miloš (advisor) ; Hadzima, Branislav (referee) ; Karlík, Miroslav (referee)
Title: Optimization of properties of Ti based alloys for biomedical and structural applications Author: Josef Stráský Department / Institute: Department of Physics of Materials Supervisor of the doctoral thesis: Assoc. Prof. Miloš Janeček, Ph.D. Abstract: Titanium alloys belong to the mostly used biomaterials for orthopaedic implants. Advanced surface treatments of Ti alloys for orthopaedic use and newly developed biomedical beta-Ti alloys are investigated in this thesis. Wide spectrum of experimental techniques was employed in order to correlate material processing, microstructure and mechanical properties. Electric discharge machining was used as a biocompatibility enhancing surface treatment of Ti-6Al-4V alloy, but the treated material suffered from the poor fatigue performance. Two subsequent surface treatments - chemical etching and shot- peening - were proposed and it was shown that their combination significantly improves the fatigue performance of the material making it applicable in orthopaedics. This process was patented in the Czech Republic. The thesis further reviews complex problematic of biocompatible beta-Ti alloys. Several new biocompatible beta-Ti alloys were designed on the basis of Ti-Nb-Zr-Ta quaternary alloy. The effect of Fe, Si and O additions on microstructure, elastic modulus and...
|
|
|
Complex investigation of fine-grained polycrystals of Cu and CuZr alloy processed by equal channel angular pressing a high pressure torsion
Srba, Ondřej ; Janeček, Miloš (advisor) ; Hadzima, Branislav (referee) ; Karlík, Miroslav (referee)
Title: Complex investigation of fine-grained polycrystals of Cu and CuZr alloy processed by equal channel angular pressing and high pressure torsion Author: RNDr.Ondřej Srba Department: Department of Physics of Materials, Faculty of Mathematics and Physics, Charles University Prague Supervisor: Doc. RNDr. Miloš Janeček, CSc. Abstract: In the thesis the microstructure development, mechanical, elastic and corrosion properties of deformed specimens of pure Cu and binary alloy CuZr processed by equal channel angular pressing (ECAP) are investigated. Several properties of pure Cu processed by ECAP are compared with properties of the same material processed by high pressure torsion (HPT). The microstructure development is characterized in detail by several experimental techniques (light and electron microscopy, electron back scatter diffraction, positron annihilation spectroscopy, etc.). The microstructure development in specimens processed by ECAP is characterized by the continuous fragmentation of the initial coarse grain structure and the formation of new grains having the sizes in the submicrocrystalline range (of 460 nm and 260 nm in Cu and CuZr alloy, respectively). During the deformation by ECAP the fraction of high-angle grain boundaries, the dislocation density and the concentration of vacancies are...
|
|
| |
|
|
Effect of microstructure on mechanisms of plastic deformation in fine-grained magnesium alloys
Minárik, Peter ; Král, Robert (advisor) ; Hadzima, Branislav (referee)
In this work were studied effects of the grain refinement on the mechanical properties and the corrosion resistance of magnesium alloys potential for medical applications - AE21 and AE42. Mechanical properties changed after ECAP pressing in consistency with literature data. Enhanced corrosion resistance in AE42 alloy was achieved by the grain refinement. Corrosion layer created on the surface was observed by light and electron microscopy. Effect of the grain size on the character of the corrosion layer was investigated. AE42 alloy is suitable for further investigation as potential biodegradable material. AE21 alloy was excluded from further investigation due to low corrosion resistance even after ECAP treatment.
|
guest ::
