|
|
Power Supply System for Housis Using Renewable Resources
Gálus, Matej ; Punčochář, Josef (referee) ; Šebesta, Jiří (advisor)
The aim of this thesis is to describe the advantages of simultaneous utilization of photovoltaic and wind electricity in an autonomous system, supplying the household with electricity without connection to the electrical grid. The most used methods of connecting photovoltaic modules and wind generators to chemical batteries are discussed. Several maximum power point tracking methods and their properties are described. A block schematic diagram of an autonomous off-grid system utilizing chemical accumulators is proposed. The system also contains an inverter producing standard mains voltage 230 VAC to supply common household appliances. A Quasi-Square Wave converter topology was chosen for all three power converters. An experimental 180 W output power QSW converter with one controllable switch was designed, simulated with Pspice, manufactured and tested to verify the efficiency of the topology. Excellent agreement was found between predicted and measured efficiency at full output power. Efficiency for reliable operation varies between 89% and 92,2% at full power and depends mainly power inductor and MOSFET used. After successful evaluation of QSW topology, the power converters for the main system were designed. Because of higher power, the converters were designed as four-phase, whereas each phase contains two controllable switches to boost efficiency mainly in low-power area. The most critical and difficult part of the project was to design the mixed-signal control sections for the converters to ensure proper switching of two controllable MOSFETs in each phase. For user interactivity, main control board with graphic LC display, Ethernet module and SD memory card slot was also manufactured.
|
|
|
Switching power supply with zero voltage switching
Pešl, Jiří ; Pavlík, Michal (referee) ; Boušek, Jaroslav (advisor)
Diploma thesis describes the design of an switched mode power supply with switching at zero voltage for driving the anode of Anode-layer type ion source. First aim of thesis is ion sources and specialy Anode-layer type of ion source in detail. Main aim of thesis are important aspects of the design of switching mode power supply, which comes later the detailed construction of an switched mode power supply with output voltage 2800 V at output power 2800 W.
|
|
|
Switched Mode Power Supplies
Španěl, Petr ; Lettl,, Jiří (referee) ; Kadaník,, Petr (referee) ; Procházka, Petr (advisor)
This thesis deals with switched mode power supplies based on resonant principle to achieve high efficiency. Several ways of switched mode power supplies optimalisation are described as part of the work to achieve better efficiency. Priparily, the new generation of switching elements based on SiC and resonant topology are used to achieve significant switching loss minimization. The selected resonant topology is simualted in detail and then built with focus on high efficiency. The main content of the work consists in the design and realization of the switched mode power supply with selected control algorithms and their comparison. The problems associated with usage of new SiC MOSFET generation in TO-247-4L package are being solved within the design and implementation of the power source. To solve the main problems, new 3rd SiC MOSFET gate driver was developer for working with switching frequencies in hundreds of kHz and resisting very high voltage stress on the controlled transistor. The next part of the gate driver is the overcurrent protection. The overcurrent limit can be set easily by changing one component. This protection reacts very quickly in hundreds of nanoseconds, so it is capable of saving the converter even in branch failure and going to hard short circuit. The functional sample of the series resonant converter was built and revated in the work. The converter based on 3. Generation of SiC MOSFET transistors from Cree in a modern case TO-247-4L was built. For this inverter, it was also necessary to develop both the control scheme and the resonance frequency tracking to achieve accurate switching and thus achieve the use of the resonant principle of the converter to the maximum extent possible. The result of this work is up to 3 kW converter with adjustable output voltage while maintaining high efficiency up to 96%.
|
|
| |
|
|
Switched Mode Power Supplies
Španěl, Petr ; Lettl,, Jiří (referee) ; Kadaník,, Petr (referee) ; Procházka, Petr (advisor)
This thesis deals with switched mode power supplies based on resonant principle to achieve high efficiency. Several ways of switched mode power supplies optimalisation are described as part of the work to achieve better efficiency. Priparily, the new generation of switching elements based on SiC and resonant topology are used to achieve significant switching loss minimization. The selected resonant topology is simualted in detail and then built with focus on high efficiency. The main content of the work consists in the design and realization of the switched mode power supply with selected control algorithms and their comparison. The problems associated with usage of new SiC MOSFET generation in TO-247-4L package are being solved within the design and implementation of the power source. To solve the main problems, new 3rd SiC MOSFET gate driver was developer for working with switching frequencies in hundreds of kHz and resisting very high voltage stress on the controlled transistor. The next part of the gate driver is the overcurrent protection. The overcurrent limit can be set easily by changing one component. This protection reacts very quickly in hundreds of nanoseconds, so it is capable of saving the converter even in branch failure and going to hard short circuit. The functional sample of the series resonant converter was built and revated in the work. The converter based on 3. Generation of SiC MOSFET transistors from Cree in a modern case TO-247-4L was built. For this inverter, it was also necessary to develop both the control scheme and the resonance frequency tracking to achieve accurate switching and thus achieve the use of the resonant principle of the converter to the maximum extent possible. The result of this work is up to 3 kW converter with adjustable output voltage while maintaining high efficiency up to 96%.
|
|
|
Switching power supply with zero voltage switching
Pešl, Jiří ; Pavlík, Michal (referee) ; Boušek, Jaroslav (advisor)
Diploma thesis describes the design of an switched mode power supply with switching at zero voltage for driving the anode of Anode-layer type ion source. First aim of thesis is ion sources and specialy Anode-layer type of ion source in detail. Main aim of thesis are important aspects of the design of switching mode power supply, which comes later the detailed construction of an switched mode power supply with output voltage 2800 V at output power 2800 W.
|
|
|
Power Supply System for Housis Using Renewable Resources
Gálus, Matej ; Punčochář, Josef (referee) ; Šebesta, Jiří (advisor)
The aim of this thesis is to describe the advantages of simultaneous utilization of photovoltaic and wind electricity in an autonomous system, supplying the household with electricity without connection to the electrical grid. The most used methods of connecting photovoltaic modules and wind generators to chemical batteries are discussed. Several maximum power point tracking methods and their properties are described. A block schematic diagram of an autonomous off-grid system utilizing chemical accumulators is proposed. The system also contains an inverter producing standard mains voltage 230 VAC to supply common household appliances. A Quasi-Square Wave converter topology was chosen for all three power converters. An experimental 180 W output power QSW converter with one controllable switch was designed, simulated with Pspice, manufactured and tested to verify the efficiency of the topology. Excellent agreement was found between predicted and measured efficiency at full output power. Efficiency for reliable operation varies between 89% and 92,2% at full power and depends mainly power inductor and MOSFET used. After successful evaluation of QSW topology, the power converters for the main system were designed. Because of higher power, the converters were designed as four-phase, whereas each phase contains two controllable switches to boost efficiency mainly in low-power area. The most critical and difficult part of the project was to design the mixed-signal control sections for the converters to ensure proper switching of two controllable MOSFETs in each phase. For user interactivity, main control board with graphic LC display, Ethernet module and SD memory card slot was also manufactured.
|
guest ::
