|
|
PAH bond to nanoparticles of atmospheric aerosol: substrate specifity.
Bendl, Jan ; Hovorka, Jan (advisor) ; Cajthaml, Tomáš (referee)
Polycyclic aromatic hydrocarbons (PAHs) are reviewed including their chemical and chemical- physical features, their impact on health and the environment. Different behaviour of PAHs is mentioned. The detailed instruction for the measurement using high-volume cascade impactor BGI 900 (Hi-Vol) is described. Cleaning, equilibration, weighting, protection against contamination of the substrates and technique of the measurement were introduced. The experiment was done: under the last teflon back-up filter the extra PUF substrate was placed, where after the air exposition the significant amounts of gaseous phase of phenanthrene, anthracene, fluoranthene, pyrene and benzo(a)anthracene were captured. The extent of the volatile PAHs capture correlated positively with the vapour pressure (ranging from 10-4 to 10-1 Pa.). The other measured PAHs (coronene, benzo(ghi)perylene, chrysene, benzo(b)fluoranthene, benzo(k)fluoranthene, benzo(a)pyrene, dibenzo(a,h)anthracene and indeno(1,2,3-cd)pyrene) with vapour pressure from 10-5 to 10-10 Pa were not captured. The experiment found out that polyurethane (PUF) substrates captured in noticeable amount the volatile phase of PAHs and therefore the correction for the capture of gaseous phase in the particle size fractions of PAHs was calculated. The deduction for the...
|
|
|
Charakterisation of fungal aerosol in size segregated aerosol
Shamratova, Kseniia ; Hovorka, Jan (advisor) ; Kozáková, Jana (referee)
This bachelor thesis deals with the issue of bioaerosol, properties of airborne fungal spores, describes their significance, concentration, methods of spreading and influence on human health. This work provides information about sampling and detection methods of bioaeerosol. Was proved the suitability of using of the first step of the high volume cascade impactor (Hi-Vol) BGI-900 to collect biaerosol samples for subsequent scanning electron microscope (SEM) analysis. Using the optimized method, bioaerosol samples were isolated from the polyurethane foam, which is the impact substrate of the impactor. Bioaerosol samples were taken from 3 locations in the Czech Republic: Prague, Březno, Láz. During the SEM analysis of 15 bioaerosol samples, 605 SEM images were taken, on 340 of them were identified fungal spores. The smallest number of spores were found in Prague. Approximately the same amount of fungal spores was found in Březno and Láz. Fungal spores were identified into 9 genus, 1 family, and 1 species. The percentage of deformed spores in Prague was 48%, in Březno 23%, in Láz 25%. The greatest variability of spores was at the Březno and Láz localities. The most common fungal genus was the Cladosporium genus. No positive or negative correlation was observed between the number of fungi and the...
|
|
|
Pollen charakterisation in size segregated aerosol
Kolpakova, Anna ; Hovorka, Jan (advisor) ; Zíková, Naděžda (referee)
This bachelor thesis, in literature review, deals with bioaerosol issue, describes meaning of pollen, ways of pollen spreading and its influence on human health, summarize methods of pollen sampling from the air and common ways of pollen grains identification. In the experimental part, the use of the first stage of a High Volumetric Cascade Impactor (Hi-Vol) BGI-900 for bioaerosol sampling and subsequent SEM analysis was proved. Method of pollen separation from the impaction substrate, polyurethane foam, into homogeneous deposit on Nylon filter was optimized. Representative portion of the deposit was analyzed by SEM. There were taken 485 SEM pictures from 12 samples in 3 localities in the ČR. Pollen grains were identified in 295 SEM and determined into 9 genus and 4 families and grain deformities were quantified to be 24, 18, 50% for Prague, Brezno and Láz localities. Number of pollen increased with total aerosol mass in Prague locality only. Thre aleo identified insect secrction products borochomomes in the samples. Key words: pollen, pollen grain, bioaerosol, cascade impactor, SEM.
|
|
|
PAH bond to nanoparticles of atmospheric aerosol: substrate specifity.
Bendl, Jan ; Hovorka, Jan (advisor) ; Cajthaml, Tomáš (referee)
Polycyclic aromatic hydrocarbons (PAHs) are reviewed including their chemical and chemical- physical features, their impact on health and the environment. Different behaviour of PAHs is mentioned. The detailed instruction for the measurement using high-volume cascade impactor BGI 900 (Hi-Vol) is described. Cleaning, equilibration, weighting, protection against contamination of the substrates and technique of the measurement were introduced. The experiment was done: under the last teflon back-up filter the extra PUF substrate was placed, where after the air exposition the significant amounts of gaseous phase of phenanthrene, anthracene, fluoranthene, pyrene and benzo(a)anthracene were captured. The extent of the volatile PAHs capture correlated positively with the vapour pressure (ranging from 10-4 to 10-1 Pa.). The other measured PAHs (coronene, benzo(ghi)perylene, chrysene, benzo(b)fluoranthene, benzo(k)fluoranthene, benzo(a)pyrene, dibenzo(a,h)anthracene and indeno(1,2,3-cd)pyrene) with vapour pressure from 10-5 to 10-10 Pa were not captured. The experiment found out that polyurethane (PUF) substrates captured in noticeable amount the volatile phase of PAHs and therefore the correction for the capture of gaseous phase in the particle size fractions of PAHs was calculated. The deduction for the...
|
guest ::
