|
|
Computational simulation of cross-roll leveling of rods
Benešovský, Marek ; Vrbka, Jan (referee) ; Petruška, Jindřich (advisor)
Final thesis describes two variants of computational models to simulate cross-roll leveling of rods, which are based on the Lagrangian approach to describe the continuum. Implementation of both variants was performed in ANSYS software, and their main difference lies in the choice of the type of elements for the discretization. An integral part of this thesis is the description of the principle, which is an evaluation of the curvature of the rod after completion of the simulation leveling. In the other part of the work are presented the results, which are then compared with realized experiment and simulation algorithm for cross-roll leveling based on the Euler approach. The final part is dedicated to the optimal settings of the leveller.
|
|
| |
|
|
Computational analysis of cross roll straightening of rods
Štourač, Vít ; Šebek, František (referee) ; Petruška, Jindřich (advisor)
Today is on products from the perspective of quality placed an increasing emphasis. This work is focused to the analyze of cross roll straghtening of long semifinished products with a circular cross-section. This process increased quality of semifinished products from the perspective of their curvature, because they do not reach the required limit values. Curvature of the semifinished product is due to residual stress, which is during straghtening using plastic deformation of the material redistributed and the semifinished product is leveled. This work analyzes the effect of rotation of straightening rolls on the distributiom of contact pressure between the straightening semifinished product and the roll of straightener. Author then analyzes effect of input parameters of program to straightening at the final curvature of the semifinished product. With the experience gained, then try to adjust some input parameters.
|
|
|
Design of the straightening machines XRK 7-200
Sobotka, Jiří ; Jonáš, Jiří (referee) ; Omes, Jiří (advisor)
The thesis Design of the straightening machines XRK 7-200 deals with the types of straightening machines and their principles. Further, procedures for construction proposals of seven-roll straighteners with rods of 100-200 mm in diameter are described. These proposals are primarily made for upper and lower crossbeams. The thesis also presents calculations of drives and set screws.
|
|
|
Computational simulation of cross-roll leveling of rods
Benešovský, Marek ; Vrbka, Jan (referee) ; Petruška, Jindřich (advisor)
Final thesis describes two variants of computational models to simulate cross-roll leveling of rods, which are based on the Lagrangian approach to describe the continuum. Implementation of both variants was performed in ANSYS software, and their main difference lies in the choice of the type of elements for the discretization. An integral part of this thesis is the description of the principle, which is an evaluation of the curvature of the rod after completion of the simulation leveling. In the other part of the work are presented the results, which are then compared with realized experiment and simulation algorithm for cross-roll leveling based on the Euler approach. The final part is dedicated to the optimal settings of the leveller.
|
|
|
Design of the straightening machines XRK 7-200
Sobotka, Jiří ; Jonáš, Jiří (referee) ; Omes, Jiří (advisor)
The thesis Design of the straightening machines XRK 7-200 deals with the types of straightening machines and their principles. Further, procedures for construction proposals of seven-roll straighteners with rods of 100-200 mm in diameter are described. These proposals are primarily made for upper and lower crossbeams. The thesis also presents calculations of drives and set screws.
|
|
|
Computational analysis of cross roll straightening of rods
Štourač, Vít ; Šebek, František (referee) ; Petruška, Jindřich (advisor)
Today is on products from the perspective of quality placed an increasing emphasis. This work is focused to the analyze of cross roll straghtening of long semifinished products with a circular cross-section. This process increased quality of semifinished products from the perspective of their curvature, because they do not reach the required limit values. Curvature of the semifinished product is due to residual stress, which is during straghtening using plastic deformation of the material redistributed and the semifinished product is leveled. This work analyzes the effect of rotation of straightening rolls on the distributiom of contact pressure between the straightening semifinished product and the roll of straightener. Author then analyzes effect of input parameters of program to straightening at the final curvature of the semifinished product. With the experience gained, then try to adjust some input parameters.
|
|
| |
guest ::
