|
|
Preparation of training materials for high voltage switchgears
Nosek, Jan ; Kozel, Tomáš (referee) ; Lázničková, Ilona (advisor)
This Bachelor thesis documents the creation of training materials for high voltage switchgear. Most of the work is devoted to introduction of products of ABB company, which the training materials are developed for. The main emphasis was on introduction of the UniGear ZS1 switchgear, which the main product of ABB's high voltage switchgear domain is. The last chapter is devoted to the analysis of the different levels of training materials.
|
|
|
Design of overvoltage arresters in high voltage switchgear depending up parameters of connected load
Němec, Ondřej ; Bernard, Michal (referee) ; Lázničková, Ilona (advisor)
The purpose of this thesis is to introduce the reader about the problems of design of surge arresters. The first part of this thesis describes problems of surge. In the next part of this thesis are described test pulses needed to test surge arresters. The next issues of this thesis are medium voltage switchgears and surge arresters ABB and their test. In the next part ot this thesis are described type of network according earthing of transformers. The other point of this thesis are aplications of surge arresters, figures and calculation for networks, generators, transformers and motors. In the conclusion of this thesis is the appreciation of whole problems about surge arresters.
|
|
|
Technology design of switchgear manufacturing
Žilák, Marek ; Dvořák, Milan (referee) ; Štroner, Marek (advisor)
This Master´s Thesis developed as a part of the follow-up Master´s Program studies in the field of M-STM Manufacturing Technology and Management in Industry introduces a technological proposal of switchgear manufacturing technology. Based on the research and assessment of the current status in the casing production, a technological process is proposed including technological and design documentation. The conclusion of this work is focused on the techno-economic evaluation of the selected production method and savings opportunities.
|
|
|
Electrical installation in family home
Pokorný, Marek ; Bátora, Branislav (referee) ; Macháček, Jan (advisor)
The goal of this bachelor paper with the topic " Electrical installation in family home" is to describe laws and public notices that relate to an electrical setting; relevant norms and conditions for a connection to a distribution network (low tension service lines); ways of connections and its location. Furthermore, this paper describes operational conditions, external effects, dimensioning, cabel lodgements and protection (its ways, principles, security and conductor). In a separate chapter low tensinon switch-boards distribution and its instrumentation is covered. Another sphere of this bachelor paper is the field of illumination and lamps. The following chapter deals with sorts of electrical setting (classic, intelligent), low-tension electrical setting (PC distributions), fire and safty electrical setting and audit report elaboration. A practical sample of a electrical installation in family home is shown at the end of this paper
|
|
|
Calculation of heat and force field UniGear ZS1
Mokrý, Lukáš ; ABB, Drahomír Tůma, (referee) ; Dohnal, Petr (advisor)
The aim of my work is to describe high-voltage switchgear type UniGear 500R, which is part of UniGear switchgears family. I will focus on heating issue of one 500R unit and its parts during operation. Maximum values of this heating is limited by standards and can´t be exceed to ensure safe and reliable operation. That is why the heating tests are necessary part of designing and developing switchgears. Calculation will be made by two different ways. First is classic one-pole heating net method and second is numerical simulation in Solidworks flow simulation program. Except the theoretical description there will be presented also used 3D model and explanation of both method, used to calculation and simulation. Last point of this work is measuring of this type of switchgear and getting real data. The main point there is to compare measured values with values calculated and decide if is possible to simulate tests with appropriate accuracy. Then would be also possible to substitute the real test in laboratory, which costs many thousand crowns and takes lots hours of time. This work is collaborated with EJF division of ABB Company, where I am employed. Heating issues in this company is always on process, because of developing and improving of their products. So this work could be helpful in this field. ABB provides all materials needed, especially technical catalogues, 3D model and final values from laboratory measuring. Support from college faculty is mainly in study consultations and proposing of calculations making. In the end of work will be make final comparison and evaluation of achieved results.
|
|
|
Simulation of Heat Transfer in Low-Voltage Switchboard MNS - Optimization of Heat Transfer into The Switchboard
Czudek, Aleš ; Maxa, Jiří (referee) ; Vyroubal, Petr (advisor)
The thesis includes diagnostics temperature field of industrial low voltage. Place of origin, flow and heat transfer are important aspects in the design of the switchgear, especially in terms of proper equipment layout. The correctness of the design of the switchgear is verified by measuring the practical temperature field during testing or in work mode. To determine the temperature profile, it is necessary to measure the temperature at various points of the switchgear, either contact or contactless method. Measurements are performed on standardized low voltage switchboards, which are located power elements. The goal is to replace costly and time-consuming field testing switchgear efficient simulation of the temperature field mathematical model developed switchboards.
|
|
| |
|
| |
|
|
Design the Transformer Station for the Outgoing Power of Cogeneration Unit
Pastorek, Jaroslav ; Procházka, Aleš (referee) ; Orságová, Jaroslava (advisor)
The thesis deals with the design of a transformer station for the outgoing power of cogeneration unit with an electric capacity of up to 1 MW. The thesis describes the design procedure of individual devices such as a transformer with a nominal ratio 22/0,4 kV, high voltage switchgears and low voltage switchgears. With the proper selection of the transformer, along with the technical parameters, the economic benefits that come from its purchasing and operating costs with the transformer operation are also considered. Based on this, the economic comparison of selected types of oil transformers during 20 years is also developed. Another part of the thesis deals with HV and LV switchgears, which are dimensioned according to shortcircuit conditions in the transformer station. In conclusion this work deals with the grounding of a transformer station and design protection in accordance PPDS.
|
|
|
Dimensioning of Earthing System in HV Switchgear
Buršík, Roman ; Matuška, Marcel (referee) ; Orságová, Jaroslava (advisor)
My master's thesis is focused on grounding of HV switchgear. The aim of this work is to create a computer program intended for dimensioning of earthing networks. The earthing networks are the most convenient alternative in term of effective grounding and distribution of ponential. They are based on latiny a flat conductor network cables and connection of appliance parts to network. Introduction of the thesis is dedicated to explanation of grounding theory and to description of requirements essential for properly designed earthing system (dimensioning of earthing system). Following chapter brings description of computer program algorithm testing propriety of an assigned earthing network for a particular switchgear. The chapter also contains description of an user interface and explanation of all features, included in the program. Last part provides presentation of program utilization to particular numerical assignment.
|
guest ::
