|
Switched power source 300 V/100 V
Horníček, Evžen ; Lutera, Ondřej (referee) ; Pavelka, Ondřej (advisor)
This thesis deals with design of switching power supply used for supplying of electronical measurement instruments. The project consists of choosing of suitable type of the converter, system design of the converter, design of the pulse transformer and the output coil. For final control of design was designed the convertor with universal control circuit and there were measured its basic parameters. Then, the universal control circuit was replaced by microcontroller.
|
|
Switch mode supplies
Hladík, Jan ; Martiš, Jan (referee) ; Patočka, Miroslav (advisor)
This thesis deals with the design of switched power supply for laboratory lessons. Forward converter was chosen as the topology of this power supply. Output voltage is adjustable from 0 V to 32 V. Power supply is capable of output current up to 10 A and output has adjustable current limiting. Following parts were designed: LC filter, pulse transformer, bridge rectifier with capacitor, power MOS-FETs driver, closed loop control with its auxiliary power supply. Cascade closed loop control is used for controlling of designed power supply. Control is analogue, operation amplifiers were used for its construction. PCB was designed for the whole power supply. Power supply was sucessfully assembled and tested.
|
|
Converter for DC Welding
Siuda, Petr ; Vorel, Pavel (referee) ; Patočka, Miroslav (advisor)
This master´s thesis with the peripheral and structural design of power converter that will be used for DC welding. The drive itself is based on the principle of two single-acting permeable converters operating in counter strokes to a mutual load. The inverter operates at a frequency of 60kHz, and its output current can be controlled from 0 - 100A. Welder is equipped with a variable constant current or power adjustment. The device is powered from a single-phase 230V.
|
|
New Conceptions of Power Pulse Converters Using Extremely Fast Switching Semiconductors Based on SiC
Kuzdas, Jan ; Chlebiš,, Petr (referee) ; Drábek,, Pavel (referee) ; Vorel, Pavel (advisor)
This work deals with high power pulse converters (tens of kW) using new semiconductor devices of silicon carbide (SiC). Firstly the current state of the issue is analyzed. A research in a specific area of high power buck converters with pulse transformer follows. There was a strong emphasis on minimizing size and weight. The design process was focused also on reliability and robustness. To achieve the defined objectives, it was necessary to use the latest available switching transistors and diodes, and an unusually high switching frequency (100 kHz at a power of about 16 kW). Due to the high switching frequency, we achieved small size of pulse transformers and output chokes. An optimization of high-frequency pulse transformer with demand on minimum volume and weight of core and windings represents a separate theoretical part of the thesis. There have been proposed several analytical solutions of optimization problems, the results of which could overlap with the implementation in practice of switching power supplies. The combination of high switching frequency, fast semiconductors and the high power brings various parasitic effects to the power circuit. In the thesis, these parasitic effects are analyzed. Solutions which minimize or completely remove those effects were theoretically designed and successfully implemented, tested and finalized in experimental part of the work. Detailed description of the implementation of functional sample and series of validation measurements are included in the final part.
|
|
Laboratory Switching Power Supply
Slezák, Jakub ; Petržela, Jiří (referee) ; Šebesta, Jiří (advisor)
This bachelor’s thesis is concerned with design switching power supply based on forward converter with output voltage regulated in the range of 3 to 30V and load current to 1 A. First of all, it discusses the theoretical solution of basic types of converters and switching power supply problems. Followed by a proposal of various parts source, which was first established in the test version on the test board. Then was proposed printed circuit board and complete mechanical solutions. Source is also equipped with digital modules for measuring voltage and current, and is protected against overload.
|
|
Power converter for artificial power net
Picmaus, Michal ; Procházka, Petr (referee) ; Patočka, Miroslav (advisor)
Diploma work deals with a converter design for an artifical power net. There is described analysis of possible solving of this converter. Next there is contained dimension of components force circumference converter, design of filtres and converter regulator. Project deals with simulation of dynamical qualities for an output changer device in settings Matlab Simulink. In this work there is even a design power board alternator, wakers and directing of alternator.
|
|
Switching supply source 5,5kV/4,3kW with silicon-carbide semiconductors
Gabriel, Petr ; Patočka, Miroslav (referee) ; Vorel, Pavel (advisor)
This thesis is about to introduce the development of switched power supply with output voltage of 5,5 kV and power of 4,3 kW. This thesis directly follows the outputs of two previous semester projects. Main task is about to finish the development of remaining printed circuit boards and perform launching of all parts of developed power supply. Next necessary task is about to assemble a functional prototype of the supply using the developed parts, performing a series of measurement supply’s parameters and creating of technical documentation of mechanical part. There are all stages of supply’s development included in this thesis. From the first part, that describes various types of converters, through the design of all the supply’s parts, to final implementation of functional prototype. There are the results of measurement supply’s parameters at the end of this thesis.
|