|
|
Evaluation of the machined surface and subsurface properties using Barkhausen noise analysis
Blažíček, Dominik ; Malec, Jiří (referee) ; Švejcar, Jiří (advisor)
Master thesis deals with the influence of milling to resulting surface integrity of gear tested by Barkhausen Noise Analysis technique. Two sets of gears milled by different machines by comparable parameters were used to solve the task. The testing of surface integrity was carried out after heat treatment and final grinding. It was experimentaly approved the effected surface/subsurface damage caused by milling remains in the material through the heat treatment. Based on these results, it can be assumed that different milling affects the resulting surface integrity after HT.
|
|
| |
|
|
Structural study of nanocrystalline titanium oxide films and their temperature stability
Chlanová, Lea ; Kužel, Radomír (advisor) ; Čapková, Pavla (referee) ; Ganev, Nikolaj (referee)
Title: Structural study of nanocrystalline titanium oxide films and their temperature stability Author: Lea Chlanová Department: Department of Condensed Matter Physics Supervisor: Prof. RNDr. Radomír Kužel, CSc., Department of Condensed Matter Physics Abstract: TiO2 thin films can exhibit photocatalytic activity and photoinduced su- perhydrophilicity depending on crystallinity, phase composition and mi- crostructure. These parameters were studied by X-ray diffraction (XRD) and reflectivity (XRR) for magnetron deposited films - nanocrystalline and amorphous, namely their temperature and time evolution. For nanocrystalline films, it was found that higher partial oxygen pressure during the deposition is beneficial. Small anatase crystallites were stable up to about 450 ◦ C. Depth-profiling XRD of some samples revealed that rutile phase was only present close to the substrate. For amorphous films it was found that the crystallization depends strongly on the film thickness and it is slower for very thin films. Evolution of the intensities of anatase diffraction peaks with annealing time could be described by a modified Avrami equation. XRD profile was relatively narrow from the very be- ginning of crystallization (at about 220 ◦ C), which indicated relatively larger crystallites (> 100 nm), and hence, nanocrystalline films...
|
|
|
Issue of Internal Tension in Materials during Machining of Thin-walled Components
Osička, Petr ; Chladil, Josef (referee) ; Sedlák, Josef (advisor)
This master thesis focuses on analysing the origins of residual stress in material caused by face milling. Representatives of three groups of aluminum alloys (5000, 6000, 7000) are compared by measurements. For measuring of the residual stress in aluminum alloys, the hole-drilling method was used by applying tensometric rosettes. In order to determine the influence of the used milling cutters', flatness of the machined surface was analyzed by comparative method. The thesis concludes with a discussion and an overall evaluation of the results.
|
|
|
Analysis of possibilities of analytical approaches suitable for evaluating of stress-strain states of idealized aortic shapes
Turčanová, Michaela ; Burša, Jiří (referee) ; Novák, Kamil (advisor)
The bachelor's thesis deals with possibilities of analytical solution of stress-strain states of arteries. The first part of the thesis gives an information about cardiovascular system and continuum mechanics. The calculation was performed analytically and also numerically using ANSYS program. The analytical calculation was carried out considering non-linear theory of thin and thick-walled vessels involving the residual stress and fictitious temperature approach. Furthermore, the analysis of solutions of abdominal aortic aneurysms was done based on linear theory. Description of other methods of linear theory and techniques of calculating with residual stress are briefly summarized.
|
|
| |
|
|
Analysis of residual stresses in arterial wall
Novák, Kamil ; Fuis, Vladimír (referee) ; Burša, Jiří (advisor)
This thesis deals with computational modeling of the influence of residual stresses in idealized geometry of blood vessels and subsequent application of acquired knowledge to abdominal aortic aneurysm. In the terms of quality of the computational model, we reduced the uncertainties that are included in the computational model without considering the influence of residual stresses. The basic assumption of homogenization significant peaks of the stress between inner and outer vessel wall was met for each level of the computational model Methods that have been used are: deformation method (opening angle method), inverse mechanics of large deformations, fictitious temperature – for linear elastic material and hyperelastic material defined by the constitutive model. Numerical verification was carried out using program ANSYS.
|
|
|
Removal of residual stress in thin sheets by tension leveling
Dymáček, Martin ; Návrat, Tomáš (referee) ; Petruška, Jindřich (advisor)
Tension leveling is a process used in the steel industry in order to eliminate any shape imperfections of cold-rolled thin strips. The master thesis deals with developing a computer program that generates basic parameters of tension leveling line. The theoretical part of the thesis summarizes the types of the shape imperfections in strips, their causes and the principles of their elimination. This part also presents the mechanism of tension leveling and describes the present-day design of tension levelers. The practical part of the thesis starts with an analytical description of stress-strain behaviour of strip during tension leveling (supposing the simplified conditions). A computer program that allows devising basic parameters of tension leveling line is created on the basis of these analytical relations. The program results are successfully verified by numerical model based on the finite element method (FEM) created in the program ANSYS. Then the interdependencies of certain input and output parameters of created program are determined. These interdependencies can be used as effective design of tension leveling lines.
|
|
| |
|
| |
guest ::
