|
|
Modular Horizontal Heat Recovery Steam Generator
Primes, Alois ; Nantl, Radomír (referee) ; Lisý, Martin (advisor)
This thesis deals with the design of a Heat Recovery Steam Generator (HRSG). Theintroductory part is devoted to a brief description of the boiler, the specified parametersand the compilation of the temperature profile. The main computational part of thiswork is divided into 6 parts. The first contains preparatory calculations, including thecalculation of boiler eiciency. In the second part, a flue gas duct is designed. This isfollowed by a thermal calculation of the boiler for all heat exchange surfaces. The last 3parts deal with the design of the drum, piping and the loss of boiler draft calculation.
|
|
| |
|
|
Thermal calculation of direct fired heater
Sénáši, Martin ; Kilkovský, Bohuslav (referee) ; Jegla, Zdeněk (advisor)
The main aim of the thesis is to evaluete properties of a simplified thermal calculation of the direct fired heater published in the journal Applied Energy at 2010 and its application to specific industrial cases. At first, general issues of process heaters are talk over. Second, calculation model in cited article is briefly introduced. After that, custom computational model at program Maple is created in accordance with published article. Subsequently, the model is applied to the existing process furnaces in the form of a check calculation. An integral part of the work is also a detailed discussion of the results obtained.
|
|
|
Biomass and waste gasification and cogeneration by the help of microturbine
Kašpar, Matěj ; Najser,, Jan (referee) ; Baláš, Marek (advisor)
This diploma thesis investigate the question of combined production of heat and power by the gasification of biomass. The introduction describes basic dilemma energy conversion from biomass. Further, special attention at the gasification technology and it´s usage at combined heat and power production is paid. The main section includes schematic proposal cycle with use of microturbine 80 [kWe] as well as basic calculation, which serves as a base for folowing project optimization. For discussed optimization is made concept of configuration, thermal and aerodynamics calculation for both heat exchangers B1 and B2. Last but not least these heat exangers were compared by different aspects such as influence of deposits on power transfer and pressure loss. At the end of the work calculated numeric values are discussed and the project of heat exchanger with it´s advantages for practise are summarised.
|
|
|
The use of waste heat cogeneration units for steam and heating
Jež, Dalibor ; Skála, Zdeněk (referee) ; Baláš, Marek (advisor)
This master’s thesis deals with design of technological system for heating and process steam generation. The source of energy is a cogeneration unit. The thesis is divided into several parts. The first part is design of technological system and description. The second part is realized stoichiometric calculation and the thermal balance of steam boiler. The main part of thesis is design of the waste heat steam boiler. The thermal calculation, aerodynamic calculation, hydraulic calculation and strength calculation were made. The thesis also includes the drawing of designed waste heat steam boiler.
|
|
|
Grate Biomass Boiler
Dražka, Ondřej ; Křemínský, Pavel (referee) ; Lisý, Martin (advisor)
The aim of the thesis is a design of a grate steam boiler with capacity of 35 t/h and output steam parameters with temperature 430 °C and pressure 4,1 MPa. The first part of the thesis deals with stoichiometric calculations and boiler efficiency. The theses mainly focuses on the heat transfer calculation and the geometric design of individual heat transfer surfaces. The specifics of fuel are taken into consideration. The drawing of the basic boiler scheme is a part of the thesis.
|
|
|
Mathematical modeling of district heating net
Pařízková, Iva ; Kracík, Petr (referee) ; Pospíšil, Jiří (advisor)
This thesis is focused on creating an iterative model for thermal and hydraulic calculation of heating net in Visual Basic of Application. Flowing medium considered is hot water. Although data for heating network in Brno are recorded in this model, its use for any other heating network is possible. This model allows also calculation of minimal temperature of the source and calculation of heat loss of every consumer. This is very useful when considering, if supplying some of the consumers with the heat from a local source would not be more effective. The second part of this text is aimed to evaluation of different ways how to reduce the heat loss in heat network for source Červený mlýn. Both current situation and possibilities for the future are considered.
|
|
|
Changing the fuel base of the coal boiler
Kallas, Miloš ; Burša, Robert (referee) ; Baláš, Marek (advisor)
This thesis deals with the change of the fuel base of a coal boiler due to the reduction of CO2 emissions and its thermal recalculation. In the first part, there is implemented calculation of the combusting chamber. This is followed by the recalculation of the heat transfer surfaces. The emphasis is placed on the preservation of the exsiting steam parametrs.
|
|
|
Grate RDF Boiler
Lachman, Jakub ; Šilhavý, Karel (referee) ; Lisý, Martin (advisor)
The master’s thesis deals with the design of a boiler for RDF combustion, based on the required power output and superheated steam parameters. The first part of the thesis focuses on combustion calculations. Boiler efficiency is also calculated in this chapter, using the heat balance efficiency method. The main part of the thesis consists of dimensional design and heat transfer calculations. The precision of the calculations is checked at the end of the thesis along with the chlorine corrosion, which is considered because of the higher amount of chlorine in the fuel. The thesis comes with a basic schematic of the designed boiler.
|
|
| |
guest ::
