|
|
Ventilation in sports facility
Frühauf, Patrik ; Šikula, Ondřej (referee) ; Rubinová, Olga (advisor)
The bachelor thesis deals with ventilation in sports facility. The objective of this work is to design two or three air-conditioning units in the part of assigned building. The bachelor thesis is divided into three main parts: theoretical part, calculation part and project.The theme for theoretical part is air distribution. Attention is especially devoted to airflow in a room, piping system and distribution elements. The calculation part is practically focused on designing of air-condition units. The last part of bachelor thesis is formed as documentation for sports facility.
|
|
|
Steam turbine - condensation formation and discharge
Zouhar, Adam ; Filip, Patrik (referee) ; Fiedler, Jan (advisor)
Master thesis is dealing with the issue of condensate creation and removal from the Nesher Ramle steam turbine during start-up and steady state. At the beginning a preliminary calculation of heat balance and the turbine itself is done. It is followed by description and design of drainage system supplemented by calculation of the steam flow through the orifices. Steam flow calculation was done via S. D. Morris, Pavelek with Kalčík and Ambrož, all three methods were compared. The main goal is the theoretical calculation of the amount of condensate created during start-up which is influenced by its initial state from which it is started. Three default states are considered, cold, warm and hot. In the last chapter the comparison of theoretical calculation with the measured data on real turbine is done and it is supported by the evaluation of the data from the measurement of the steam turbine at steady state on maximum power and half power. From the steady state analysis, percentage of water flow to expander from the total amount of condensate formed in the turbine were obtained.
|
|
|
Calculation of the heat balance of latent heat utilization of flue gases by means of a condenser
Toman, Filip ; Baláš, Marek (referee) ; Pospíšil, Jiří (advisor)
Thesis is focused on calculation of the condenser of flue gas, which is created by burning of natural gas. In the first part is theoretical overview of equations describing film condensation and physical properties of the flue gas. The second part deals with practical thermal calculation of the specified condenser. In third part parametric study is done in which a tempature of cooling water at inlet and the coefficient of excess air are changed. The last part of the thesis is dedicated to geometric design of the flue gas condenser whose required power is 8 MW.
|
|
|
Ventilation of the wellness sports center
Valcha, Tomáš ; Uher, Pavel (referee) ; Blasinski, Petr (advisor)
This bachelor thesis deals with design of the ventilation in the wellness center. The main objective of this paper is to design three air-conditioning devices to meet all requirements specified in thesis assigment for the indoor microclimate in the subject object. The content is divided into three parts, namely: theory, where the project, measurement techniques and theory, and governing regulations are discussed followed by computations, with the focus on the design of the aforementioned ventilation devices and finally the documentation, containing all the documentation for the ventilation of the wellness center.
|
|
|
The savings in heating buildings
Rokůsek, Petr ; Hořínková, Lucie (referee) ; Počinková, Marcela (advisor)
This thesis theoretically in Part A deals with the solution in savings heating building and heating hot water. It examines the impact of austerity measures on the overall need for and consumption of heat energy and its economic impact and compared with each other in order to achieve maximum efficiency. Part B is their subsequent application to a given object - a residental building, various design alternatives and the resulting energy savings improvements. Experimental Part C deals with indirect measurement of the thermal conductivity of building materials.
|
|
|
Biomass Retrofit 250 MW Steam Turbine
Novák, Martin ; Josef, Švagr (referee) ; Josef, Švagr (referee) ; Fiedler, Jan (advisor)
There is a description of modernisation steam condensing turbine in this Master´s thesis. Electric output is decreased from 250 MW to 160 MW. This thesis is divided into two parts, there is a calculation of heat balance in first part and a calculation of blading in second part. Detail drawing and heat balance are the most important results of this Master´s thesis.
|
|
|
Draft boilers for co-firing blast furnace gas and coke oven gas
Machara, Radek ; Křemínský, Pavel (referee) ; Baláš, Marek (advisor)
The diploma thesis deals with design of gas steam boiler with given parameters of steam. Blast furnace and coke oven gas are used as fuel. At the beginning of this work, both co-fired fuels are presented to us, their chemical analysis and stoichiometry are performed. The main part of the diploma thesis deals with the dimensioning of individual heat exchange surfaces such as steam superheaters, evaporators, economizers and air heaters. All heat exchange surfaces meet recommended parameters such as recommended steam rates, flue gas, etc. At the end, the total heat balance of the boiler is performed. Part of the work is also drawing documentation showing the main dimensions of the boiler. It is also indicated the connection of individual heat exchange surfaces.
|
|
|
Material properties research for use in high-temperature solar thermal storage tank
Šot, František ; Vala, Jiří (referee) ; TROJAN,, Karel (referee) ; Steuer,, Radek (referee) ; Šťastník, Stanislav (advisor)
The use of thermal storage energy, using phase change materials appears to be an effective way to store thermal energy storage with the benefits of the high amount of energy while maintaining isothermal nature of the process. PCM methods are used in latent thermal storage systems for heat pumps, as well as in solar engineering or for temperature control in spacecraft. The past decade has extended these principles for cooling and heating in the building. There are a number of PCM systems, which operate over a wide temperature range, are used in various applications. This document includes a brief overview of the development and analysis of available thermal storage working mainly on the principle of PCM.
|
|
|
Increased power microturbines operating in indirect circulation
Polák, Luboš ; Fiedler, Jan (referee) ; Škorpík, Jiří (advisor)
Turbogenerator unit 100B TGU, produced in the First Brno Engineering Velká Bíteš a.s., works in Brayton indirect circulation. The aim of this work is the proposal to increase performance levels of technological unit in which the micro-turbine is applied. The work presents various ways to increase performance and efficiency of circulation. The possible options are compared with each of the technological and economic terms. Based on these criteria was selected variant feeding additional water into the circulation. For this design was the work of a mathematical model based on, which was established as the economic balance of the selected variants. The thesis also proposes a technological scheme, which is already incorporated the selected variant and an outline of the verification tests.
|
|
|
Fuid bed boiler for biomass
Bytešník, Jan ; Skála, Zdeněk (advisor)
This master thesis designes the calculation of fluid boiler with specific part - the circular fluid bed. The heat is given by combustion of wood biomass. The thesis is devided into several parts. All necessary elementary results are going to be reached within these parts: an analysis of solid fuel, stechiometry calculation, discussion on output limits and the environmental point of view, definition of elemental heat losses and general heat efficiency, calculation and design of a combustion part and its heat loads and calculation of enthalpies with different ash concentrations. All these phases get to a successful design of the fluid boiler heat balance and sizes of heat-flow surfaces. The composition of the boiler shows the added drawing.
|
guest ::
