|
|
Extraction Condensing Steam Turbine
Drápela, Jakub ; Kracík, Petr (referee) ; Fiedler, Jan (advisor)
This diploma thesis describes a design of condensing steam turbine out of entered data of vapor parameters. There is selected a reaction blading type according to a conception of the company PBS Energo PLC. The turbine has one controlled extraction and three uncontrolled ones. The work also includes a proposal of thermal scheme, bearing and gearbox assignment. Furthermore there is also made a draft design of longitudinal section turbine
|
|
|
Steam turbine
Pokorný, Tomáš ; Novotný, Zdeněk (referee) ; Fiedler, Jan (advisor)
Condensing steam turbine. Master's thesis of master's studies of 2th years. This master's thesis is technical research. The contents of this technical research are an analysis of a mechanical equipment of that are used for condensing steam turbine, thermodynamic calculations of passage channel for specified inlet and outlet conditions of steam, design and construction, drawing of the turbine axial cross section, operating scheme of turbine and economic analysis of operation.
|
|
|
Feed Pump Condesing Steam Turbine
Uherek, Jan ; Kubiš, Zdeněk (referee) ; Fiedler, Jan (advisor)
This diploma thesis focuses on designing impulse stage steam turbine to be used as the feed pump drive. I consecutively carried out thermodynamic calculation, seals and bearings layouts, with the aim to determine the steam mass flow through the turbine. Furthermore, I conducted turbine blade toughness check-ups, determined the rotor critical rotational speed, check-up rotor critical place (bearing pin) for torsion, and created a clutch screws design. The final part of this thesis pursues the other operating states of the turbine. This thesis is amended by a mechanical drawing of the turbine transection.
|
|
|
Condensing Steam Turbine C55
Borýsek, Václav ; Fiedler, Jan (referee) ; Kracík, Petr (advisor)
This diploma thesis deals with the design of a steam condensing turbine for intake steam of pressure 125 bar, temperature 540 °C and maximal intake of steam into the turbine 130 t/h. A thermal scheme is designed, including low-pressure and high-pressure regeneration, an air condenser, a feed tank and a boiler. Afterwards a thermodynamic design of a condensing turbine is made with an A-wheel type regulating stage and a stage part with reaction blades. The design of the blades is strength-tested. Then is made the design of the compensating piston and the sealing system. In the end the characteristics of the turbine for non-design steam flows is plotted. The designed turbine has a power of 34644 kW, has a thermodynamic efficiency of 85.1% and a reheat factor of 1.046.
|
|
|
CFD simulation flow of steam in the unregulated extraction of steam turbine
Filip, Patrik ; Pospíšil, Jiří (referee) ; Fiedler, Jan (advisor)
Diploma thesis named CFD simulation of the steam flow in the unregulated extraction of the steam turbine is about an analysis of the balance piston impact on the area of the steam turbine, where the extraction is located. First part describes basic knowledge of the steam turbine in general. At the end of this chapter, there is a description of the solved steam turbine. Next chapter is about introduction to the CFD. Practical part deals with a construction of 3D models, meshing and setting of the boundary conditions in the program ANSYS CFX. The main part of this thesis summarizes the results of the CFD simulation and stipulates the temperature range on the extraction pipe. In conclusion, there is a recommendation how to determine design temperature of the extraction pipe influenced by the balance piston.
|
|
|
Steam Turbine for the Waste to Energy
Szelecky, Zsolt ; Fichtl, Richard (referee) ; Kracík, Petr (advisor)
The content of this thesis is the design of a condensing steam turbine with an output of 80 MWe to a waste incinerator with impulse blading. In this work are elaborated proposals and calculations of balancing schemes, which are used in the next part of the work as a foundation for calculation of the blades part of the turbine. The blades part is designed for two operations - for full condensing operation and for full demand operation. The turbine should contain one process offtake and three unregulated offtakes. Besides that, the thesis solves basic strength control. The thesis is finished with a technical drawing of the longitudinal cut of the turbine.
|
|
|
Small Condensing Steam Turbine
Vítek, Tomáš ; Kracík, Petr (referee) ; Fiedler, Jan (advisor)
The goal of this Master’s thesis is to create the design of a low power condensing steam turbine. The turbine has a Curtis control stage and a reaction blading. The work also contains the calculation of gland labyrinth seals and the balancing piston, specification of a forces and losses at bearings. Finally, the gearbox and generator are selected and the efficiency at generator’s clamps is specified. The Master’s thesis includes the design drawing of a longitudinal turbine view.
|
|
|
Steam Turbine in the Combi Cycle
Filoušová, Natálie ; Kracík, Petr (referee) ; Fiedler, Jan (advisor)
Diploma thesis named Steam turbine in the combi cycle deals with design of low pressure part of three-body turbine and it’s lateral outlet throat to the air condenser. Before the design itself, the thermal schema of entire turbine is calculated. Than follows the detail draft, the strength calculations are included as well. Turbine has any technological consumption of steam or any regenerativ consumption. Turbine will be suplly to Panama. The thesis includes following drawings: cut of flowing part, design of outlet throat and fixing of inner body in outer body of low pressure part. The diploma thesis is created for Doosan Škoda Power company.
|
|
|
Condesing Steam Turbine 25 MW
Mašek, Martin ; Norbert, Weber (referee) ; Norbert, Weber (referee) ; Fiedler, Jan (advisor)
Master’s thesis deals with design and calculation of one body condensing steam turbine of 25 MW with samples for paper-making industry. The thesis is focused on calculation of the turbine’s heat balance with two technological samples and regeneration which consists of two low pressure heaters and a deaerator with a power reservoir. The steam turbine is designed with a water cooling condenser with down output. The flow part is calculated with lengths of blades. There are basic strength and proportion calculations. In the end of the thesis the turbine’s heat balance is recalculated to 80% and 105% scheme according to an assignment. Another part of this thesis is a drawing of a longitudinal cut of the turbine including a connector with a gearbox.
|
|
|
Steam turbine for a small nuclear power plant
Biskup, Michal ; Fiedler, Jan (referee) ; Kracík, Petr (advisor)
This master´s thesis deals with the design of a steam turbine for a small nuclear power plant with a power of 50 MWe. In the first part of the work is proposed thermal and mass balance. The turbine has seven unregulated steam extractions, which are divided: two are for high-pressure feedwater heater, four are for low-pressure condensate heater and one is for degassing. The next chapter deals with the calculation of the regulation stage which is designed like an A-wheel and here is also strength control. Then, a pre-design and a detailed design of the stage part with the reaction blading. The stage part is consisted of eight cones with a total number of 27 stages. In the following chapters, is calculated the compensating piston, seals system and bearings. In the end, is made the consumption diagram. Part of the work is a conceptual drawing of a steam turbine section. The resulting steam turbine has a power output 50,197 MW and an internal thermodynamic efficiency of 73,9 %.
|
guest ::
